Preparation; Unpacking The Tv - JVC LT-32C600 Instruction Manual

32" led smart hd tv

Hide thumbs

Table Of Contents

Table of Contents

Chapter

Preparation

Thank you

Your new TV has many features and incorporates the latest technology to enhance your viewing

experience. We recommend that you spend some time reading this instruction manual so that you fully

understand these features. You will also find some hints and tips to help you resolve any issues.

Read all the safety instructions carefully before use and keep this instruction manual for future reference.

Unpacking the TV

Remove all packaging from the TV. Retain the packaging. If you dispose of it please do so according to local regulations.

The following items are included:

TV Stand (feet) x 2

Instruction Manual

32" LED Smart HD TV

LT-32C600

Instruction Manual

•

If items are missing, or damaged please contact Partmaster (UK only).

Tel: 0344 800 3456 for assistance. Parts are available for 7 years after purchase.

JVC 32' LED Smart HD TV LT-32C600 Manual.indd 7

for purchasing your new JVC TV.

Stand screws x2

Setup in

Quick Start Guide

15mins

32" LED Smart HD TV

LT-32C600

JVC 32' LED Smart HD TV LT-32C600 Quick Start.indd 1-3

Quick Start Guide

Thank you

for purchasing your new JVC TV.

Your new TV incorporates the latest technology to enhance your viewing

The latest eco-friendly power-saving technology will switch off the TV if

experience. We would suggest that you allow about 15 mins for initial setup.

it is left on and idle for 4 hours. Please refer to "Auto Standby" under the

Connecting the Aerial and Turning on the TV

"Time Settings" section of the instruction manual for more detail.

Please follow this guide for a successful first time installation.

What's in the Box?

1. Connect one end of the RF coaxial cable to the aerial socket on the wall and the other end of the cable to the ANT socket on the back of your TV.

2. Plug the TV into a mains socket and switch on at the mains.

Remove all packaging from the unit. Retain the packaging. If you dispose of it please do so according to any local regulations.

3. In standby mode, press the

button on the remote control to turn the TV on. The LED indicator will flash for a few seconds then the TV will switch on.

Remote Control/

Stand Screws x 2

Please inspect your TV for damage after unpacking. If

AAA Batteries x2

TV Stand x 2

Instruction Manual

you do notice any damage please consult your dealer.

Quick Start Guide

Operating Your Remote Control

1. Slide open the battery compartment on the back of the remote control.

LAN

SPDIF

VGA

Optic.OUT

AV IN

2. Insert two AAA size batteries. Make sure to match the (+) and ( - ) ends of

the batteries with the (+) and ( - ) ends indicated in the battery compartment.

LAN

3. Slide the battery compartment cover back into place. Make sure it clicks into place.

For extra safety use the screw supplied to screw the battery compartment closed.

VGA

SPDIF

Installing the Base Stand

Optic.OUT

Fitting the Stand to the TV

1. Ensure the TV is switched off and not connected to the mains power supply.

2. Lay the TV down on a flat surface ideally on the edge of a table so the base of the TV slightly overhangs the edge of the table, with the back side facing up.

AV IN

Please make sure a soft cushioned material (such as a dry bath towel or thick piece of foam) is placed beneath the screen.

3. Fit each leg to your TV using the screws supplied.

For wall mounting instructions please refer to your Instruction Book.

RF coaxial cable

Cushioned

Protective

Table

(not included)

material

bag

Router

(not included)

LAN

SPDIF

VGA

Optic.OUT

AV IN

Optional

If you want to connect to the internet via a wired connection

then connect your ethernet cable to the LAN socket.

• Do not connect the TV to the mains supply until you have completed all the connections.

• Always disconnect the TV from the mains socket when not in use for a long period of time.

The LCD display is very fragile, and must be protected at all times when installing and removing the base stand. Be sure that no hard or sharp object, or

• The

button on the remote control is only used for switching the TV into standby, it does not disconnect the TV from the mains power.

anything that could scratch or damage the LCD display, comes into contact with it. DO NOT exert pressure on the front of the TV at any time because the

screen could crack.

To completely disconnect the mains power, please remove the mains plug from the mains socket.

LANG.

BACK

EXIT

Remote Control /

AAA Batteries x 2

18/12/2020 09:00

23/12/2020 14:41

Table of Contents