Advertisement
Quick Links
ASSEMBLY AND INSTALLATION
T0568 / T0602
W
WARNING: Turn off the main power at circuit breaker before installing fixture.
AVERTISSEMENT: Coupez la source d'alimentation principale au panneau
central de disjoncteurs avant d'installer le luminaire.
NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. READ AND SAVE THESE INSTRUCTIONS.
Important to Know
1. Read all instructions carefully before installation and operation.
2. If you are not familiar with state and local electrical codes, it is
recommended that you consult with a qualified electrician.
3. Before installation, shut off power at the main fuse or circuit
breaker box. Be aware that simply turning off the wall switch is
not sufficient to prevent an electrical shock.
4. This fixture requires a 120V AC, 60 Hz power source.
5. Do not attempt to take the lantern apart; there are no
serviceable parts inside.
6. To avoid sensor damage by lightning or electrical surge, make
sure the grounding wire is securely connected.
7. For general safety and to avoid any possible damage to the
sensor, be sure the power is switched "off" before replacing the
bulb.
8. Compatible with most LED dimmable bulb.
Maximum Wattage: 60W
Dimmable Bulb
Work Temperature: -4°F~104°F
Outlet Box
House Grounding Wire
Green Grounding Screw
Mounting Plate Unit (A)
Mounting Screw (B)
Fixture Grounding Wire
Wire Connector (C)
Fixture Wire
Set Screw (D)
Rubber Pad (E)
INSTRUCTIONS
Incandescent
Bulb or 20W LED
Max.60W Type A Bulb
(not included)
Features
1. Energy saving fixture.
2. Use dim-to-full brightness where dim-illumination
is preferred, such as your front entrance. Use
off-to-full brightness where off/on illumination is
preferred, such as your backyard.
3. When in manual override mode, use wall switch
to keep the light ON till dawn.
Hardware Package (included)
Mounting Plate Unit (A)
Set Screw (D)
Backplate
Page 1 / 5
Mounting Screw (B) Wire Connector (C)
Rubber Pad (E)
Fixture
Socket
Glass Panel
210317
Advertisement
Related Manuals for Vaxcel T0568
Summary of Contents for Vaxcel T0568
- Page 1 ASSEMBLY AND INSTALLATION INSTRUCTIONS T0568 / T0602 WARNING: Turn off the main power at circuit breaker before installing fixture. AVERTISSEMENT: Coupez la source d’alimentation principale au panneau central de disjoncteurs avant d’installer le luminaire. NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
-
Page 2: Installation Steps
Installation Steps Turn off the power at fuse or circuit box 1. Unscrew the two set screws (D), remove the two rubber pads (E) and the mounting plate unit (A) from the backplate. 2. Attach the mounting plate unit (A) to the outlet box by using two mounting screws (B). Note: Make sure that two set holes are lined up horizontally to make the fixture level. -
Page 3: Function And Operation
Function and Operation MODES OF OPERATION Choose a mode by sliding the switch on the back of the sensor. When power is first applied, the light will turn on immediately. Wait for 100 seconds to allow the sensor to warm up. 1. -
Page 4: Troubleshooting
NOTE: 1. The sensitivity of the motion sensor will increase as the Where you install your lantern is important: environmental temperature gets cooler. For best performance, Be sure the light is mounted straight on the wall; gently clean the lens with a soft cloth every 1 or 2 months to otherwise, the detection distance may be limited. - Page 5 The following parts are available for re-order if damaged or missing. Spare Parts List: Mounting Hardware 6214MM (1SET) for T0568 6355MM (1SET) for T0602 Glass Panel Mounting Plate Unit (A) Mounting Screw (B) Wire Connector (C) Set screw (D) Rubber Pad (E) 10153CS A: 13-1/4"...