Biffi ICON 2000 / ICON 2000 AD
Addendum A to InstructIon And operAtIng mAnuAl
c Ex d e IIB+H2 T4 Gb / c Ex tb IIIC T135°C Db IP66/68
c Ex d e ia IIB+H2 T4 Gb / c Ex tb IIIC T135°C Db IP66/68
index
1
Safety instructions ��������������������������������� 1
1�1
General ����������������������������������������������������� 1
1�2
Identification of main parts ��������������������� 1
2
Check for right application �������������������� 2
2�1
Marking ���������������������������������������������������� 2
3
Applicable general standards and
regulations ���������������������������������������������� 2
4
Terms and conditions ����������������������������� 2
5
Manufacturer's liability ������������������������� 2
6
Storage and pre-installation ����������������� 3
6�1
Storage procedure ����������������������������������� 3
6�2
Checks to be performed before
installation ������������������������������������������������ 3
7
installation ���������������������������������������������� 3
7�1
Working condition ������������������������������������ 3
7�1�1 Models and temperature������������������������� 3
7�1�2 Base unit with extensions [A]
or [B] or [C] ����������������������������������������������� 3
7�2
Identification of entry ������������������������������� 3
7�2�1 Base actuator ������������������������������������������� 3
7�2�2 Base actuator with extension [A]
on the control compartment ������������������� 3
7�2�3 Base actuator with extensions
[B] or [C] on the terminal board
compartment ������������������������������������������� 4
7�3
Wiring ������������������������������������������������������� 4
7�4
Cable connection ������������������������������������� 4
7�5
Installation in ambient with
explosive dusts ����������������������������������������� 4
8
Maintenance �������������������������������������������� 5
8�1
Periodic inspections �������������������������������� 5
8�2
Dismantling and reassembling �������������� 5
8�3
Repairs ����������������������������������������������������� 5
www.pentair.com/valves
1� SAfETy INSTRuCTIONS
1.1 generAl
This Addendum A is an integration to
ICON 2000 main IOM VCIOM-01232 to
prescribe the safety instructions applicable to
all the electric actuators Series ICON 2000 /
ICON 2000 AD either as a base unit either when
they are equipped with an optional extension [A]
for additional entry mounted on the control
compartment or when they are equipped
with an optional extension [B] with additional
entries or with an optional extension [C] with
optional electronic card both mounted on the
terminal board compartment, as identified
by the pictures here below, when they are
installed in Hazardous Areas as defined by the
IEC/EN 60079-10-1 IEC/EN 60079-10-2�
under the same conditions, the optional
extensions [A], [B] or [C], can be mounted on
a base unit ICON 2000 / ICON 2000 AD already
installed on field�
WArning
It is assumed that the installation, setting,
commissioning, maintenance and repair works
are carried out by qualified personnel and
checked by responsible specialists.
Both the base unit ICON 2000 /
ICON 2000 AD and optional extension are
designed in accordance with the applicable
international rules and specifications but in
any case the following regulation must be
observed:
- The general installation and safety
regulations�
- The proper use of personal protective devices
(glasses, clothing, gloves)�
- The proper use of tools, lifting and transport
equipment�
© 2012 Pentair plc� All rights reserved�
1.2 idenTifiCATion of MAin pArTS
Base unit
Base unit with extension [A]
Base unit with extensions [B] or [C]
VCioM-03019-en 15/03