Parts Lists - Eaton Heavy Duty 2 Series Manual

Parts List
Models 3322/3922/4622
ITEM P/N QTY . DESCRIPTION
1 See Table 2.0 1
2 See Table 3.0 1
3 See Table 4.0, 4.1 1
4 103090-325 8
5 See Table 18.0 1
6,7,8,9 See Table 5.0-6.1 1
12 See Table 7.0-7.1 1
13 See Table 9.0 1
14 1032411Bearing Plate (Models 33/39)
14 1041981 Bearing Plate (Model 46)
15,16,17,18,19,20,21,22,23,24
See Table 10.0,10.1
28 108300* 2
26 See Table 11.0, 11.1 1
27 8761-144* 2
28 108300* 2
29 See Table 11.1
30 See Table 11.1
31 95862-088 8
32 8761-139* 2
33 16254-8 1
34 96097-050 1
35 16254-28 1
40 103232-000 1
41 See Table 15.0 A/R
42/43 108295-000 1
44 107575 2
45 108331 2
46 108823 2
47 108152 1
48 See Table 14.0** 1
49 8785-012* 1
53 108214 2
54 16048-480 2
55 107582 2
56 98202 3
57 110457-000* 4
59 8761-017* 2
60 108562-000* 2
61 25083-01 1
62 107887 1
63 25706-006 2
64 25090-010 1
65 25090-004 3
66 25083-004 12
67 25083-002 3
68 96559 1
70 111402-000 1
71, 72 See Table 5.0
76 4994730-xxx (1) 2
See Table 12.0
78 110700-xxx (1) 1
See Table 13.0,13.1
REFERENCE
Main Housing
Drive Shaft Sub-assembly
End Cover
Hex Bolt HD 3/8-16 Gr. 8
End Cover Gasket
Control Valve
Rotating Kit Sub-assembly
Propel Valve/V-Groove
/Quiet Plate
Charge Pump Subassembly
Ring Seal
Servo Piston Sub-assembly
O-Ring
Ring Seal
Servo Piston Cover
Servo Piston Cover
Hex Bolt HD 5/16-18 Gr 5
O-Ring
Thread seal
Nut, Hex .50-20
Washer
Bearing Cup
End Cover Bearing Shim Kit
Bearing Cup/Bearing Cone
Subassembly
Swash Bearing Sub-assembly
Race Pin
Clocking Link
Slide Block
Low Pressure Relief Valve Plug
O-Ring
Hold Down Spring
Hold Down Washer
Hollow Dowel
Dowel
Static Face Seal
O-Ring (between end cover
and housing)
Back-up Ring (between end
cover and housing)
O-Ring Plug
O-Ring Plug Soc HD
O-Ring Plug
O-Ring Plug
O-Ring Plug
O-Ring Plug
(not all positions shown)
O-Ring Plug (used with
Pressure Override option)
Shipping Strap (not shown)
Control Link Sub-assembly
Manual Control
Relief Valve, Pressure Override
(optional)
Relief Valve and/or
Check Valve (B Port)
EATON Heavy-Duty Series 2 Hydrostatic Pumps Parts and Repair E-PUPI-TS004-E October 2004
ITEM P/N
PAGES
9
79 110700-XXXXXX
See Table 13.0, 13.1
9
10-11
80,81,82 See Table 1.0
83 95653-012
25
84 95653-006
12-16
17-18
85 **
19 108307
86 16160-125
87 8761-016*
95, 96, 97, 105
20-22
116 **
23 117 **
118 **
119 95653-012
23 163 4994730-XXX
See Table 12.0
23
176 499161-001
*available in gasket kit 990710-000
**available in kit
(1)See Table 14.1 for correct part number identification
and pressure settings.
Used only with remote or
26
pressure side filtration.
25
12
23
23
QTY . DESCRIPTION
(1) 1 Relief Valve and/or Check Valve (A Port)
1 Control Valve Orifice
2 Soc Pipe Plug .125-27 NPTF
(inside charge pump inlet port)
2 Soc Pipe Plug .062-27 NPTF
(inside charge pump inlet port)
1 Magnetic Speed Sensor (optional)
1 Plug (optional)
1 Retaining Ring (optional)
1 O-Ring
See Charge Pump Sub-assembly
1 Drive Shaft Seal
1 Ring, Retaining
1 Spacer
1 Soc Pipe Plug .125-27 NPTF (optional)
1 Pressure Override Relief Valve (optional)
2 Cap Nut
REFERENCE
PAGES
24
8
20-22
24
7