Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for FOR-A HVS-100PSM
Summary of Contents for FOR-A HVS-100PSM
- Page 1 INSTALLATION GUIDE HVS-100PSM Redundant Power Supply for MU Edition...
- Page 2 Upon Receipt Unpacking HVS-100PSM cards and their accessories are fully inspected and adjusted prior to shipment. Operation can be performed immediately upon completing all required connections and operational settings. Check your received items against the packing lists below. Check to ensure no damage has occurred during shipment.
-
Page 3: Table Of Contents
Table of Contents 1. Prior to Starting ......................... 5 2. Installing the HVS-100PSM ....................... 5 2-1. Removing the Power Supply Tray ..................5 2-2. Installing the HVS-100PSM....................5 2-3. Connecting Cables ......................6 2-3-1. Installing Cable A ......................7 2-3-2. Installing Cable B ......................8 2-3-3. -
Page 5: Prior To Starting
1. Prior to Starting The HVS-100PSM is a power supply unit specially designed for the HVS-100 switcher. Each switcher comes with two power supply slots with a single power supply unit installed. This optional HVS-100PSM power supply unit allows you to operate an HVS-100 continuously, even if one power supply unit fails. -
Page 6: Connecting Cables
(4) Secure the power supply unit to the tray using the four supplied W-sems screws. Screws 2-3. Connecting Cables Connect the HVS-100PSM to the switcher using the supplied cables: Cables A, B and C. The completed wiring installation is as shown below. Follow the following instructions to complete the cable installation. -
Page 7: Installing Cable A
(2) Use the four supplied binding screws (large) to secure both sides of the connectors to the plate. Label facing UP Cable A Standard power supply HVS-100PSM 8-pin 5-pin plug plug (3) Connect the 8-pin plug (white) of Cable A to Socket a on the power supply tray as shown below. -
Page 8: Installing Cable B
Socket c Standard power supply Cable B Socket c' HVS-100PSM 2-3-3. Fixing Cables (1) Open the existing blue cable clip (shown below) and bundle the cables together, so they do not fall off the tray edge. (2) Secure Cable A as shown below with the supplied cable tie. -
Page 9: Installing Cable C
Secure cables. Secure the GND cable with screw. Standard power supply Normal washer GND cable HVS-100PSM Toothed washer Socket d 2-4. Re-inserting the Power Supply Tray (1) Re-insert the power supply tray in reverse order. IMPORTANT Insert the power supply tray carefully so as not to pinch or damage cables. -
Page 10: Checking Operation
FOR-A supplier. 3-2. Checking the Status Menu Follow the procedure below to verify that the HVS-100PSM is properly installed. (1) The MENU button on the control panel should blink when powered ON. (2) Press MENU, then press SETUP. - Page 11 Warning This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
- Page 12 Tel: +1 352-371-1505 Fax: +1 714-894-5399 FOR-A Latin America and the Caribbean Miami Office Tel: +1 657-600-5759 FOR-A Latin America and the Caribbean Sao Paulo Office Tel: +55 (0)11-99913-3751 FOR-A Europe S.r.l. Via Volturno, 37, 20861 Brugherio MB, Italy Tel: +39 039-916-4811...
Need help?
Do you have a question about the HVS-100PSM and is the answer not in the manual?
Questions and answers