Table of Contents
Advertisement
USER MAINTENANCE INSTRUCTIONS
HUMIDITY
WARNING: Avoid high humidity levels in your home.
Mold, mildew, fungi and bacteria which may be harmful
to health thrive in areas with continued high humidity
levels; therefore, every precaution should be taken to
make sure your plumbing fixtures, including bathtubs,
hydrotherapy baths, or showers do not become a source
of high humidity due to improper installations or leaks.
To avoid having your plumbing fixtures become a source
of unwanted humidity, please make sure the following
steps are taken prior to installation.
1. Make sure the area where the bathtub or shower is
installed is well vented and allows enough ventilation
and air circulation to dry the bathroom environment
within a short time after taking a bath or shower.
2. If your bath or shower unit is tiled-in, use units with an
integral tile flange or make sure a tile flange kit or a
similar mechanical barrier is installed to prevent shower
spray, splash, or overflow to leak behind the bathtub.
3. Make sure the plumber properly tests your
hydrotherapy bath before it is roughed in to make sure
there are no leaks and it is installed with proper access
to bath equipment.
4. Make sure that all the plumbing and fixtures in the
bathroom are in good working order and have no leaks.
5. Do not use carpeting or other materials or furniture,
which can hold moisture in your bathroom.
6. Use disinfectant to clean any bathroom surfaces which
are regularly exposed to moisture.
7. Clean and disinfect humidifier and dehumidifiers as
recommended by the manufacturer. Replace the air
filter on the HVAC unit once a month.
8. Clean moldy surfaces as soon as any mold appears
by using a detergent/soapy solution and appropriate
household cleaner. Always use gloves during cleaning.
Dispose of any sponges or rags used to clean mold.
CLEANING
With minimum care, your acrylic-surfaced bath will retain
its high-luster finish for many years. For regular cleaning
use Jason Bath Cleaner or a mild NONABRASIVE liquid
detergent solution (i.e. glass cleaner) and a soft, wet
cloth or sponge. Do not run the hydrotherapy system with
foaming cleaners or soaps. Rinse the bath thoroughly
after cleaning.
Jason International, Inc. • 501.771.4477
SURFACE MAINTENANCE
Areas with minor scratches or dull surfaces can be
restored by applying commercially available plastic
polish (i.e. Novus Plastic Polish No. 2, available at your
Jason dealer), followed by an application of acrylic paste
wax. Buff the surface with a clean soft cloth. Do not use
sandpaper, steel wool, or abrasive rubbing compounds.
If scratches are too deep to rub out, or if the damage
penetrates the acrylic surface, consult your dealer for
recommendations on surface repair.
AIR HEATER AND AIR TEMPERATURE
The air heater incorporated into the air blower is designed
to preheat the incoming air to body temperature, not to heat
the bath water. The air heater automatically comes on when
the air blower is activated. Even though all air baths provide
preheated air, occasionally some people with sensitive skin
might experience a cold air sensation. This sensation is
caused by the swiftly moving heated air bubbles blowing
on the wet skin. This phenomenon can be related to the
use of a fan for cooling on a hot day. While the ambient
temperature does not change, the moving air makes you
feel cooler. Avoiding this cold air sensation is among the
reasons Jason avoids placing air jets directly beneath the
body. If you experience a cool air sensation, which is most
noticeable during the first few minutes of an air bath, simply
move your body slightly away from the closest jets.
FLUSHING / SANITIZING
Upon start-up and not to exceed 90 days, your bath and
plumbing system should be flushed. To do so, close the
drain and fill the bath with warm water to at least two (2)
inches [5.1 cm] above the highest jet. Pour in Jason Bath
System Cleaner and follow the directions on the bottle. DO
NOT use bleach or other chlorinated cleansers directly on
the metal trim.
REPAIR
Refer all plumbing or electrical repair to a qualified service
technician. DO NOT ATTEMPT TO RESOLVE THE
PROBLEM. This can result in danger of electrical shock
or damage to the unit and will VOID THE WARRANTY.
Remember, when contacting your dealer or service
representative, always have your serial number, proof of
purchase, and model number. This will ensure a quick
response on warranty items. The serial number can be
found on the front page of this manual or on the small card
adhered to the back of the bath just above the equipment.
ALL WARRANTY REPAIRS MUST BE AUTHORIZED
BY THE MANUFACTURER BEFORE WORK IS
STARTED
Page 15 of 18
Customer Service : 800.255.5766
Copyright © 2014 Jason International.
Advertisement
Table of Contents
