Chevrolet 2011 Cruze Owner's Manual

Chevrolet 2011 Cruze Owner's Manual

Hide thumbs Also See for 2011 Cruze:
Table of Contents

Advertisement

. . . . . . . . . . . . . . . . . . . . . . . . 1-1
Instrument Panel . . . . . . . . . . . . . . 1-2
Initial Drive Information . . . . . . . . 1-4
Vehicle Features . . . . . . . . . . . . . 1-15
Performance and
Maintenance . . . . . . . . . . . . . . . . 1-19
Keys and Locks . . . . . . . . . . . . . . . 2-2
Doors . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
Vehicle Security. . . . . . . . . . . . . . 2-10
Exterior Mirrors . . . . . . . . . . . . . . . 2-11
Interior Mirrors . . . . . . . . . . . . . . . . 2-13
Windows . . . . . . . . . . . . . . . . . . . . . 2-14
Roof . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17
Head Restraints . . . . . . . . . . . . . . . 3-2
Front Seats . . . . . . . . . . . . . . . . . . . . 3-3
Rear Seats . . . . . . . . . . . . . . . . . . . . 3-8
Safety Belts . . . . . . . . . . . . . . . . . . 3-10
Airbag System . . . . . . . . . . . . . . . . 3-26
Child Restraints . . . . . . . . . . . . . . 3-40
. . . 2-1
. . . . . . . . . . . . . . . . . . . . . . . 4-1
Storage Compartments . . . . . . . . 4-1
Controls . . . . . . . . . . . . . . . . . . . . . . . 5-2
Warning Lights, Gauges, and
Indicators . . . . . . . . . . . . . . . . . . . . 5-7
Information Displays . . . . . . . . . . 5-23
Vehicle Messages . . . . . . . . . . . . 5-26
Vehicle Personalization . . . . . . . 5-33
. . . . . . . . . 3-1
Exterior Lighting . . . . . . . . . . . . . . . 6-1
Interior Lighting . . . . . . . . . . . . . . . . 6-5
Lighting Features . . . . . . . . . . . . . . 6-6
Introduction . . . . . . . . . . . . . . . . . . . . 7-1
Radio . . . . . . . . . . . . . . . . . . . . . . . . . 7-11
Audio Players . . . . . . . . . . . . . . . . 7-17
Phone . . . . . . . . . . . . . . . . . . . . . . . . 7-22
. . . . 5-1
Climate Control Systems . . . . . . 8-1
Air Vents . . . . . . . . . . . . . . . . . . . . . . . 8-6
Maintenance . . . . . . . . . . . . . . . . . . . 8-7
. . . . . . . . . . . . . . . . . . . . . . . 6-1
. . . . . . . . . 7-1
. . . . . . . . . . . . . 8-1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 2011 Cruze and is the answer not in the manual?

Questions and answers

Summary of Contents for Chevrolet 2011 Cruze

  • Page 1 ......1-1 Instrument Panel ....1-2 Initial Drive Information .
  • Page 2: Table Of Contents

    ..9-1 Driving Information ... . . 9-2 Starting and Operating ..9-16 Engine Exhaust ....9-23 Automatic Transmission .
  • Page 3 The names, logos, emblems, slogans, vehicle model names, and vehicle body designs appearing in this manual including, but not limited to, GM, the GM logo, CHEVROLET, the CHEVROLET Emblem, and CRUZE are trademarks and/or service marks of General Motors LLC, its subsidiaries, affiliates, or licensors.
  • Page 4: Controls

    To quickly locate information about the vehicle, use the Index in the back of the manual. It is an alphabetical list of what is in the manual and the page number where it can be found. Warning messages found on vehicle labels and in this manual describe hazards and what to do to avoid or reduce them.
  • Page 5 Here are some additional symbols that may be found on the vehicle and what they mean. For more information on the symbol, refer to the Index. Airbag Readiness Light Air Conditioning Antilock Brake System (ABS) Audio Steering Wheel Controls ® or OnStar Brake System Warning Light Charging System...
  • Page 7: Doors

    Instrument Panel Overview ..1-2 Initial Drive Information ..1-4 Remote Keyless Entry (RKE) System ..... . 1-4 Remote Vehicle Start .
  • Page 9 (If Equipped). Turn and Lane Change Lever. Driver Information Center (DIC) Buttons. See Equipped). Infotainment Display Screen. Light Sensor. See M. Passenger Airbag. See N. Hood Release. See O. Data Link Connector (DLC) (Out of View). See S. Driver Airbag. See Ignition Switch.
  • Page 10 (If Equipped). Equipped). (If Equipped). AB. Passenger Knee Airbag. See This section provides a brief overview about some of the important features that may or may not be on your specific vehicle. For more detailed information, refer to each of the features which can be found later in this owner manual.
  • Page 11: Climate Control Systems

    Press and hold briefly to open the trunk. Press and hold briefly to locate the vehicle. Press and hold for at least two seconds to sound the panic alarm. Press again to cancel the panic alarm. For vehicles with this feature, the engine can be started from outside of the vehicle.
  • Page 12: Windows

    To lock or unlock the vehicle from outside, use the Remote Keyless Entry (RKE) transmitter or the key. From inside the vehicle, use the power door lock switch. The power door lock switch is on the instrument panel. Press to unlock the doors. Press to lock the doors.
  • Page 13 If available, move the lever up or down to manually raise or lower the seat. If available, move the lever up or down to raise or lower the front of the seat cushion. To recline the seatback: 1. Lift the lever. 2.
  • Page 14: Front Seats

    To return the seatback to an upright position: 1. Lift the lever fully without applying pressure to the seatback, and the seatback returns to the upright position. 2. Push and pull on the seatback to make sure it is locked. To adjust a power driver seat, if equipped: Move the seat forward or...
  • Page 15: Roof

    Press the control once for the highest setting. With each press of the control, the heated seat will change to the next lower setting, and then the off setting. Three lights indicate the highest setting and one light the lowest. for more information.
  • Page 16 The passenger airbag status indicator will be visible on the instrument panel when the vehicle is started. See Controls for the outside power mirrors are on the driver door. 1. Turn the selector switch to L (left) or R (right) to choose the driver or passenger mirror.
  • Page 17 To adjust the steering wheel: 1. Pull the lever (A) down. 2. Move the steering wheel up or down. 3. Pull or push the steering wheel closer or away from you. 4. Push the lever (A) up to lock the steering wheel in place.
  • Page 18 This feature controls the brightness of the instrument panel controls and infotainment display screen. The thumbwheel is located to the left of the steering column on the instrument panel. Turn the thumbwheel up or down and hold, to brighten or dim the instrument panel controls and infotainment display screen.
  • Page 19 With the ignition in ACC/ ACCESSORY or ON/RUN, move the windshield wiper lever to select the wiper speed. Fast wipes. Slow wipes. Turn the band up for more frequent wipes or down for less frequent wipes. Turns the windshield wipers off. Single wipe, briefly move the wiper lever down.
  • Page 20 A. Temperature Control B. Bi-level Air Mode C. Floor Air Mode D. Vent Air Mode E. Fan Control Driver and Passenger Heated Seats (If Equipped) G. Rear Window Defogger H. Recirculation Defog Air Conditioning K. Defrost A. Temperature Control B. Rear Window Defogger C.
  • Page 21 2. Press the shift lever forward (+) to upshift or rearward ( ) to downshift. An M and the current gear will be displayed in the Driver Information Center (DIC). If the vehicle has a manual transmission, it will have an up-shift light that indicates when to shift to the next higher gear for the best fuel economy.
  • Page 22 5. To save the time and return to the Time Settings menu, press the BACK button at any time or press the MENU knob after adjusting the minutes. 1. Press the CONFIG button and select Time Settings. 2. Highlight 12/24 Hour Format. 3.
  • Page 23 For vehicles with audio steering wheel controls, some audio controls can be adjusted at the steering wheel. Press to interact with the available Bluetooth, OnStar, or navigation system. Press to silence the vehicle speakers only. Press again to turn the sound on. For vehicles with OnStar or Bluetooth systems, press to reject an incoming call, or to end a current call.
  • Page 24 Press to disengage cruise control without erasing the set speed from memory. If the vehicle has a navigation system, there is a separate navigation system manual that includes information on the radio, audio players, and navigation system. The navigation system provides detailed maps of most major freeways and roads.
  • Page 25 The traction control system limits wheel spin. The system is on when the vehicle is started. To turn off traction control, press and release located on the console. illuminates and the appropriate DIC message displays. See Press and release again to turn traction control back on.
  • Page 26: Maintenance

    During cooler conditions, the low tire pressure warning light may appear when the vehicle is first started and then turn off. This may be an early indicator that the tire pressures are getting low and the tires need to be inflated to the proper pressure.
  • Page 27 Follow recommended scheduled maintenance. U.S.: TTY Users: Canada: As the owner of a new Chevrolet, you are automatically enrolled in the Roadside Assistance program. for more information. If you have an active OnStar subscription, press the button...
  • Page 28 For vehicles with an active OnStar subscription, OnStar uses several innovative technologies and live Advisors to provide a wide range of safety, security, navigation, diagnostics, and calling services. In a crash, built in sensors automatically alert an OnStar Advisor who is immediately connected to the vehicle to see if you need help.
  • Page 29 OnStar service is subject to the OnStar Terms and Conditions included in the OnStar Glove Box Kit. OnStar service requires wireless communication networks and the Global Positioning System (GPS) satellite network. Not all OnStar services are available everywhere or on all vehicles at all times. OnStar service cannot work unless the vehicle is in a place where OnStar has an agreement with a...
  • Page 155: Vehicle Identification

    Infotainment System Introduction Infotainment ....7-1 Theft-Deterrent Feature ..7-1 Overview (Base Level) ..7-2 Overview (Uplevel) .
  • Page 156: Infotainment System

    Infotainment System Overview (Base Level) Turns the system on or off and adjusts the volume. B. Buttons 1 to 6 Radio: Saves and selects favorite stations. Radio: Seeks the previous station. CD: Selects the previous track or rewinds within a track.
  • Page 157 Radio: Opens the auto store stations list. BAND Changes the band while listening to the radio. Selects the radio when listening to a different audio source. K. CD/AUX Selects the CD player or an external audio source. CD Slot Insert a CD. M.
  • Page 158 Infotainment System Overview (Uplevel) Turns the system on or off and adjusts the volume. B. Buttons 1 to 6 Radio: Saves and selects favorite stations. Radio: Seeks the previous station. CD: Selects the previous track or rewinds within a track. CD: Moves up one folder level while playing an MP3.
  • Page 159 INFO Radio: Shows available information about the current station. CD: Shows available information about the current track. TONE Opens the tone menu. K. AS Radio: Opens the auto store stations list. BAND Changes the band while listening to the radio. Selects the radio when listening to a different audio source.
  • Page 160 Infotainment System Operation Controls The infotainment system is operated by using the pushbuttons, multifunction knobs, menus shown on the display, and steering wheel controls, if equipped. Turning the System On or Off (Volume/Power): Press to turn the system on and off. Automatic Switch Off If the infotainment system has been turned on after the ignition is...
  • Page 161 Turn to: Select a menu, or a menu option. Select a value. BACK: Press to: Exit a menu. Return from a submenu screen to the previous menu screen. Delete the last character in a sequence. Selecting a Menu Option 1. Turn the MENU knob to scroll through available menu options.
  • Page 162 Infotainment System Entering a Character Sequence 1. Press the MENU knob to enter the displayed menu. 2. Turn the MENU knob to adjust the highlighted character. 3. Press the MENU knob to select the character. Press the BACK button to delete the last character in the sequence or press and hold to delete the entire character sequence.
  • Page 163 Activating a Setting 1. Turn the MENU knob to highlight the setting. 2. Press the MENU knob to activate the setting. Setting a Value 1. Turn the MENU knob to change the current value of the setting. 2. Press the MENU knob to confirm the setting.
  • Page 164 7-10 Infotainment System Adjusting the Treble, Midrange, and Bass 1. Press the TONE button. 2. Select Treble, Midrange, or Bass. 3. Select the value. Press the BACK button to go back to the Tone Settings menu. Adjusting the Fader and Balance 1.
  • Page 165: Radio

    Radio AM-FM Radio Control Buttons The buttons used to control the radio are: BAND: Press to turn the radio on and choose between AM, FM, and XM , if equipped. MENU: Turn to navigate the available menus and to search for stations.
  • Page 166 7-12 Infotainment System Favorites List 1. Turn the MENU knob. 2. Select Favorites List. 3. Select the station. Station Lists 1. Turn the MENU knob. 2. Select AM or FM Station List. All receivable stations in the current reception area are displayed. If a station list has not been created, an automatic station search is done.
  • Page 167 Autostore Stations AS (Autostore): Autostore searches and stores six FM and six AM stations with the strongest signal. To use autostore: 1. Press RADIO/BAND to select FM or AM. 2. Press AS for at least two seconds until a beep sounds.
  • Page 168 7-14 Infotainment System XM Categories XM channels are organized in categories. Removing or Adding Categories Channels in a category that have been removed can still be accessed by using the buttons, or the MENU knob. To add or remove categories: 1.
  • Page 169 Retrieving Channels Press the FAV button to open a favorite page or to change to another favorite page. Briefly press one of the 1 to 6 buttons to retrieve the channel. XM Messages XL (Explicit Language Channels): These channels, or any others, can be blocked by request, by calling 1-800-929-2100 in the U.S., and 1-877-438-9677 in...
  • Page 170: Radio Reception

    7-16 Infotainment System Check Antenna: If this message does not clear within a short period of time, the receiver could have a fault. Consult with your dealer. XM Not Available: If this message does not clear within a short period of time, the receiver could have a fault.
  • Page 171: Audio Players

    Satellite Radio Antenna The XM Satellite Radio antenna is located on the roof of the vehicle. Keep the antenna clear of obstructions for clear radio reception. If the vehicle has a sunroof, the performance of the XM system may be affected if the sunroof is open. Multi-Band Antenna The multi-band antenna is on the roof of the vehicle.
  • Page 172 7-18 Infotainment System Control Buttons The buttons used to control the CD player are: CD/AUX: Press to use the CD player. : Press to select tracks or to fast forward or rewind within a track. INFO: Press to display additional information about the current track that may be available.
  • Page 173 Using the CD Menu: 1. Turn the MENU knob. 2. Select Playlists/Folders. 3. Select the playlist or folder. 4. Select the track. Searching for MP3 Tracks The search feature may take some time to display the information after reading the disc due to the amount of information stored on the disc.
  • Page 174 7-20 Infotainment System Adjusting the Volume Turn the knob to adjust the volume of the infotainment system after the volume level has been set on the portable audio device. USB Port For vehicles with a USB port, the following devices may be connected and controlled by the infotainment system.
  • Page 175 Connecting and Controlling a PlaysForSure Device (PFD) or Zune Connecting a PFD or Zune Connect the PFD or Zune to the USB port. Searching for a Track Tracks can be searched for by: Playlists Artists Albums Song Titles Podcasts Genres To search for tracks: 1.
  • Page 176: Phone

    7-22 Infotainment System Tracks can be searched for by: Playlists* Artists Albums Song Titles Genres Folder View *This only displays if a playlist is found on the device. To search for tracks: 1. Turn the MENU knob. 2. Select Search. 3.
  • Page 177 Pair cell phone(s) to the vehicle. The system may not work with all cell phones. See Pairing a Phone in this section for more information. If the cell phone has voice dialing capability, learn to use that feature to access the address book or contact list.
  • Page 178 7-24 Infotainment System Audio System When using the Bluetooth system, sound comes through the vehicle's front audio system speakers and overrides the audio system. Turn knob during a call to change the volume level. The adjusted volume level remains in memory for later calls.
  • Page 179 4. Select Pair Device (Phone). A four digit Personal Identification Number (PIN) appears on the display. If the Add new GPS device option is selected, the system will start a search for Bluetooth Handsfree profile devices just like if Add new Phone was selected.
  • Page 180 7-26 Infotainment System Making a Call Using Phone Book For cell phones that support the phone book feature, the Bluetooth system can use the contacts stored on your cell phone to make calls. See your cell phone's owner's guide or contact your wireless provider to find out if this feature is supported by your phone.
  • Page 181 Call Waiting Call waiting must be supported on the Bluetooth phone and enabled by the wireless service carrier to work. Accepting a Call Turn the MENU knob to Answer and press the MENU knob. Declining a Call Turn the MENU knob to Decline and press the MENU knob.
  • Page 182 7-28 Infotainment System Bluetooth (Voice Recognition) Using Voice Recognition To use voice recognition, press the button located on the steering wheel. The system responds differently depending on what kind of infotainment system the vehicle has installed. For vehicles without a navigation system, the system responds Ready, followed by a tone.
  • Page 183 4. Start the pairing process on the cell phone that you want to pair. For help with this process, see your cell phone manufacturer's user guide. 5. Locate the device named Your Vehicle in the list on the cell phone. Follow the instructions on the cell phone to enter the PIN provided in Step 3.
  • Page 184 7-30 Infotainment System Storing and Deleting Phone Numbers The system can store up to 30 phone numbers as name tags in the Hands Free Directory that is shared between the Bluetooth and OnStar systems. The following commands are used to delete and store phone numbers. Store: This command will store a phone number or a group of numbers as a name tag.
  • Page 185 To delete all name tags: 1. Press . For vehicles with a navigation system, say Hands Free, after the tone. 2. Say Delete all name tags. Listing Stored Numbers The list command will list all the stored numbers and name tags. Using the List Command 1.
  • Page 186 7-32 Infotainment System Using the Re dial Command 1. Press . For vehicles with a navigation system, say Hands Free, after the tone. 2. After the tone, say Re dial. Once connected, the person called will be heard through the audio speakers.
  • Page 187 To Transfer Audio from the Bluetooth System to a Cell Phone During a call with the audio in the vehicle: 1. Press 2. Say Transfer Call. To Transfer Audio to the Bluetooth System from a Cell Phone During a call with the audio on the cell phone, press .
  • Page 188 7-34 Infotainment System NOTES...
  • Page 247: General Information

    General Information ..10-2 California Proposition 65 Warning ....10-3 California Perchlorate Materials Requirements ..10-3 Accessories and Modifications .
  • Page 248 Tires ......10-40 Winter Tires ....10-40 Low-Profile Tires .
  • Page 249: Engine Exhaust

    Most motor vehicles, including this one, contain and/or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Engine exhaust, many parts and systems, many fluids, and some component wear by-products contain and/or emit these chemicals.
  • Page 250: Airbag System

    You can be injured and the vehicle could be damaged if you try to do service work on a vehicle without knowing enough about it. Be sure you have sufficient knowledge, experience, the proper replacement parts, and tools before attempting any vehicle maintenance task.
  • Page 251 2. Go to the front of the vehicle and push the secondary hood release handle toward the driver side of the vehicle. 3. Lift the hood and release the hood prop from its retainer, located above the radiator. Securely place the hood prop into the slot on the underside of the hood.
  • Page 253 B. Engine Oil Dipstick. See Checking Engine Oil under C. Electric Engine Cooling Fan (Out of View). See D. Engine Oil Fill Cap. See When to Add Engine Oil under E. Remote Negative (-) Terminal. Brake/Clutch Fluid Reservoir. See Brake Fluid under (Under Cover).
  • Page 255 B. Engine Oil Dipstick. See Checking Engine Oil under C. Engine Cooling Fan (Out of View). See D. Engine Oil Fill Cap. See When to Add Engine Oil under E. Remote Negative (-) Terminal. Brake/Clutch Fluid Reservoir. See Brake Fluid under (Under Cover).
  • Page 256 Checking the oil level too soon after engine shutoff will not provide an accurate oil level reading. 2. Pull out the dipstick and clean it with a paper towel or cloth, then push it back in all the way. Remove it again, keeping the tip down, and check the level.
  • Page 257 Use of Substitute Engine Oils if dexos is unavailable: In the event that dexos approved engine oil is not available at an oil change or for maintaining proper oil level, you may use substitute engine oil displaying the API Starburst symbol and of SAE 5W-30 viscosity grade.
  • Page 258 An oil of this viscosity grade will provide easier cold starting for the engine at extremely low temperatures. When selecting an oil of the appropriate viscosity grade, be sure to always select an oil that meets the required specification, dexos. See Specification earlier in this section for more information.
  • Page 259 If the system is ever reset accidentally, the oil must be changed at 5 000 km (3,000 mi) since the last oil change. Remember to reset the oil life system whenever the oil is changed. Reset the system whenever the engine oil is changed so that the system can calculate the next engine oil change.
  • Page 260: Scheduled Maintenance

    For vehicles with a manual transmission, it is not necessary to regularly check brake/clutch fluid unless there is a leak suspected. Adding fluid will not correct a leak. A fluid loss in this system could indicate a problem. Have the system inspected and repaired.
  • Page 261 To inspect or replace the engine air cleaner/filter: 1. Remove the 6 screws that secure the cover on. 2. Lift off the cover. 3. Inspect or replace the engine air cleaner/filter. 4. Align the filter correctly. 5. Install the cover by lowering it over the filter and secure with the 6 screws.
  • Page 262 The cooling system allows the engine to maintain the correct working temperature. A. Engine Cooling Fan (Out of View) B. Engine Coolant Surge Tank and Pressure Cap An electric engine cooling fan under the hood can start up even when the engine is not running and can cause injury.
  • Page 263 Adding only plain water or some other liquid to the cooling system can be dangerous. Plain water and other liquids, can boil before the proper coolant mixture will. The coolant warning system is set for the proper coolant mixture. With plain water or the wrong mixture, the engine could get too hot but you would not get the overheat warning.
  • Page 264 The coolant surge tank is located in the engine compartment on the driver side of the vehicle. See for more information on location. If no problem is found, check to see if coolant is visible in the coolant surge tank. If coolant is visible but the coolant level is not at the indicated level mark, add a 50/50 mixture of clean, drinkable...
  • Page 265 You can be burned if you spill coolant on hot engine parts. Coolant contains ethylene glycol and it will burn if the engine parts are hot enough. Do not spill coolant on a hot engine. 1. Remove the coolant surge tank pressure cap when the cooling system, including the coolant surge tank pressure cap and...
  • Page 266 The vehicle has several indicators to warn of engine overheating. There is an engine coolant temperature gauge on the vehicle instrument panel cluster. See If the decision is made not to lift the hood when this warning appears, get service help right away. See If the decision is made to lift the hood, make sure the vehicle is parked on a level surface.
  • Page 267 If the temperature overheat gauge is no longer in the overheat zone or an overheat warning no longer displays, the vehicle can be driven. Continue to drive the vehicle slowly for about 10 minutes. Keep a safe vehicle distance from the vehicle in front.
  • Page 268 Open the cap with the washer symbol on it. Add washer fluid until the tank is full. See for reservoir location. This vehicle has front disc brakes and could have rear drum brakes or rear disc brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed.
  • Page 269 If the vehicle has rear drum brakes, they do not have wear indicators, but if a rear brake rubbing noise is heard, have the rear brake linings inspected immediately. Rear brake drums should be removed and inspected each time the tires are removed for rotation or changing.
  • Page 270 A fluid leak in the brake/clutch hydraulic system can also cause a low fluid level. Have the brake/ clutch hydraulic system fixed, since a leak means that sooner or later the brakes will not work well. Do not top off the brake/clutch fluid. Adding fluid does not correct a leak.
  • Page 271 Refer to the replacement number on the original battery label when a new battery is needed. Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling. Batteries have acid that can burn you and gas that can explode.
  • Page 272: Automatic Transmission

    3. For automatic transmission vehicles, try to start the engine in each gear. The vehicle should start only in P (Park) or N (Neutral). If the vehicle starts in any other position, contact your dealer for service. For manual transmission vehicles, put the shift lever in Neutral, push the clutch pedal down halfway, and try to start...
  • Page 273 When you are doing this check, the vehicle could begin to move. You or others could be injured and property could be damaged. Make sure there is room in front of the vehicle in case it begins to roll. Be ready to apply the regular brake at once should the vehicle begin to move.
  • Page 274 3. With the latch open, pull the wiper blade down toward the windshield far enough to release it from the J-hooked end of the wiper arm. 4. Remove the wiper blade. Allowing the wiper blade arm to touch the windshield when no wiper blade is installed could damage the windshield.
  • Page 275 1. Open the hood. See 2. Remove the connector retaining tab (A). 3. Disconnect the wiring harness connector from the bulb (C) by pressing the connector release (B) and pulling straight back. 4. Remove the bulb (C) from the headlamp assembly by turning counterclockwise and pulling straight back.
  • Page 276 3. Remove the bulb (A) from the bulb socket. 4. Install the new bulb in the bulb socket. 5. Install the bulb socket into the headlamp assembly by turning clockwise. 1. Open the trunk. 2. Remove the trunk deck trim cover (A).
  • Page 277 4. Remove the bulb from the socket (A). 5. Install the new bulb in the bulb socket. 6. Install the bulb socket by turning clockwise. 7. Install the trunk deck trim cover. A. Back-up Lamp B. Stop Lamp/Taillamp C. Turn Signal Lamp D.
  • Page 278 3. Remove the two screws, which secure the taillamp assembly. 4. Remove the taillamp assembly by pulling it straight back until the two posts disengage from the grommets. A. Sidemarker Lamp B. Turn Signal Lamp C. Stop Lamp/Taillamp D. Back-up Lamp 5.
  • Page 279 8. Install the taillamp assembly and tighten the two screws. 9. Close the two screw covers. To replace the license plate lamp bulb: 1. Remove the two screws from the license plate lamp assembly. 2. Turn and pull the license plate lamp assembly down.
  • Page 280 The vehicle has fuses and circuit breakers to protect against an electrical system overload. When the current electrical load is too heavy, the circuit breaker opens and closes, protecting the circuit until the current load returns to normal or the problem is fixed. This greatly reduces the chance of circuit overload and fire caused by electrical problems.
  • Page 281 To remove the fuse block cover, squeeze the clips and swing it up. The vehicle may not be equipped with all of the fuses, relays, and features shown. Transmission Control Module Engine Control Module Not Used...
  • Page 282: Fuel

    Canister Vent Solenoid Ignition Not Used Fuel Injection Fuel Injection/ Ignition System Engine Control Module Lambda Sensor Canister Vent Solenoid Not Used Rear Wiper Ignition/Air Quality Sensor/Aero Shutter Ignition/Airbag Fuel Control Module Not Used Fuel Pump Not Used Not Used Antilock Brake System Body Control...
  • Page 283 Rear Window Sensor Air Quality Sensor Rear Fog Lamp Rear Washer Fuel System Control Module Not Used Battery Voltage Sensor Rain Sensor Not Used Front Wipers Starter Solenoid Rear Power Windows Not Used Front Power Windows Electronic Vacuum Pump Antilock Brake System Pump Electronic Key System...
  • Page 284: Instrument Panel

    Cooling Fan K2 Cooling Fan K1 Ignition 87 Main Ignition 15 Not Used Not Used The instrument panel fuse block is in the driver side of instrument panel. To access the fuses: 1. Open the fuse block cover by pulling out at the top. 2.
  • Page 285: Information Displays

    Infotainment System/Hands free Phone Not Used Body Control Module Infotainment System Information Display/ Parking Assist Cigarette Lighter Power Outlet Body Control Module Body Control Module Body Control Module Interior Fan Not Used Power Seat Diagnostic Connector Airbag Central Locking System/Tailgate Air Conditioning System Not Used...
  • Page 286 Every new GM vehicle has high-quality tires made by a leading tire manufacturer. See the warranty manual for information regarding the tire warranty and where to get service. For additional information refer to the tire manufacturer. Poorly maintained and improperly used tires are dangerous.
  • Page 287 Winter tires, in general, are designed for increased traction on snow and ice covered roads. With winter tires, there may be decreased dry road traction, increased road noise, and shorter tread life. After changing to winter tires, be alert for changes in vehicle handling and braking.
  • Page 288 Useful information about a tire is molded into its sidewall. The examples show a typical passenger vehicle tire and a compact spare tire sidewall. The tire size is a combination of letters and numbers used to define a particular tire's width, height, aspect ratio, construction type, and service description.
  • Page 289 The type of cord and number of plies in the sidewall and under the tread. The compact spare tire or temporary use tire has a tread life of approximately 5 000 km (3,000 mi) and should not be driven at speeds over 105 km/h (65 mph).
  • Page 290 The following is an example of a typical passenger vehicle tire size. The United States version of a metric tire sizing system. The letter P as the first character in the tire size means a passenger vehicle tire engineered to standards set by the U.S.
  • Page 291 A rubber coated layer of cords that is located between the plies and the tread. Cords may be made from steel or other reinforcing materials. The tire bead contains steel wires wrapped by steel cords that hold the tire onto the rim.
  • Page 292 load rating for a tire at the maximum permissible inflation pressure for that tire. The sum of curb weight, accessory weight, vehicle capacity weight, and production options weight. number of occupants a vehicle is designed to seat multiplied by 68 kg (150 lbs). See Designated seating positions.
  • Page 293 A tire information system that provides consumers with ratings for a tire's traction, temperature, and treadwear. Ratings are determined by tire manufacturers using government testing procedures. The ratings are molded into the sidewall of the tire. See The number of designated seating positions multiplied by 68 kg (150 lbs) plus the rated cargo load.
  • Page 294 For additional information regarding how much weight the vehicle can carry, and an example of the Tire and Loading Information label, see . How the vehicle is loaded affects vehicle handling and ride comfort. Never load the vehicle with more weight than it was designed to carry.
  • Page 295 tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.) As an added safety feature, your vehicle has been equipped with a tire pressure monitoring system (TPMS) that illuminates a low tire pressure telltale when one or more of your tires is significantly under inflated.
  • Page 296 This vehicle may have a Tire Pressure Monitor System (TPMS). The TPMS is designed to warn the driver when a low tire pressure condition exists. TPMS sensors are mounted onto each tire and wheel assembly, excluding the spare tire and wheel assembly. The TPMS sensors monitor the air pressure in the tires and transmit the tire pressure readings to a receiver...
  • Page 297 Factory-installed Tire Inflator Kits use a GM-approved liquid tire sealant. Using non-approved tire sealants could damage the TPMS sensors. See information regarding the inflator kit materials and instructions. The TPMS will not function properly if one or more of the TPMS sensors are missing or inoperable.
  • Page 298 Each TPMS sensor has a unique identification code. The identification code needs to be matched to a new tire/wheel position after rotating the tires or replacing one or more of the TPMS sensors. The TPMS sensor matching process should also be performed after replacing a spare tire with a road tire containing the TPMS sensor.
  • Page 299 12. Turn the ignition to LOCK/OFF. 13. Set all four tires to the recommended air pressure level as indicated on the Tire and Loading Information label. We recommend that the tires, including the spare tire, if the vehicle has one, be inspected for signs of wear or damage at least once a month.
  • Page 300 Adjust the front and rear tires to the recommended inflation pressure on the Tire and Loading Information label after the tires have been rotated See Reset the Tire Pressure Monitor System. See Make certain that all wheel nuts are properly tightened. See Wheel Nut Torque under Rust or dirt on a wheel, or on the parts to which it is fastened, can...
  • Page 301 The rubber in tires ages over time. This also applies for the spare tire, if the vehicle has one, even if it is never used. Multiple conditions including temperatures, loading conditions, and inflation pressure maintenance affect how fast aging takes place. Tires will typically need to be replaced due to wear before they may need to be replaced due to age.
  • Page 302 Braking and handling performance may be adversely affected if all the tires are not replaced at the same time. See for information on proper tire rotation. Tires could explode during improper service. Attempting to mount or dismount a tire could cause injury or death.
  • Page 303: Wheels And Tires

    If wheels or tires are installed that are a different size than the original equipment wheels and tires, vehicle performance, including its braking, ride and handling characteristics, stability, and resistance to rollover may be affected. If the vehicle has electronic systems such as antilock brakes, rollover airbags, traction control, and electronic stability control, the performance of these...
  • Page 304 All Passenger Car Tires Must Conform to Federal Safety Requirements In Addition To These Grades. The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course.
  • Page 305 The tires and wheels were aligned and balanced at the factory to provide the longest tire life and best overall performance. Adjustments to wheel alignment and tire balancing will not be necessary on a regular basis. However, check the alignment if there is unusual tire wear or if the vehicle is pulling to one side or the other.
  • Page 306 Do not use tire chains. There is not enough clearance. Tire chains used on a vehicle without the proper amount of clearance can cause damage to the brakes, suspension, or other vehicle parts. The area damaged by the tire chains could cause loss of control and a crash.
  • Page 307 Lifting a vehicle and getting under it to do maintenance or repairs is dangerous without the appropriate safety equipment and training. If a jack is provided with the vehicle, it is designed only for changing a flat tire. If it is used for anything else, you or others could be badly injured or killed if the vehicle slips off the jack.
  • Page 308 When the vehicle has a flat tire (B), use the following example as a guide to assist in the placement of the wheel blocks (A). A. Wheel Block B. Flat Tire The following information explains how to repair or change a tire. Idling a vehicle in an enclosed area with poor ventilation is dangerous.
  • Page 309 If this vehicle has a tire sealant and compressor kit, there may not be a spare tire, tire changing equipment, and on some vehicles there may not be a place to store a tire. The tire sealant and compressor can be used to temporarily seal punctures up to 6 mm (¼...
  • Page 310 When using the tire sealant and compressor kit during cold temperatures, warm the kit in a heated environment for five minutes. This will help to inflate the tire faster. If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place.
  • Page 311 8. Press the on/off (D) button to turn the tire sealant and compressor kit on. The compressor will inject sealant and air into the tire. The pressure gauge (E) will initially show a high pressure while the compressor pushes the sealant into the tire.
  • Page 312 15. If the flat tire was able to inflate to the recommended inflation pressure, remove the maximum speed label from the sealant canister (B) and place it in a highly visible location. Do not exceed the speed on this label until the damaged tire is repaired or replaced.
  • Page 313 To use the air compressor to inflate a tire with air only and not sealant: If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place. Turn on the hazard warning flashers. See for other important safety warnings.
  • Page 314 11. Inflate the tire to the recommended inflation pressure using the pressure gauge (E). The recommended inflation pressure can be found on the Tire and Loading Information label. See The pressure gauge (E) may read higher than the actual tire pressure while the compressor is on.
  • Page 315 4. Turn the sealant canister (B) so the inflator filling hose is aligned with the slot in the compressor. 5. Lift the sealant canister (B) from the compressor and replace with a new sealant canister. See your dealer for more information. To install a new sealant canister: 1.
  • Page 316 3. Pull the inflator kit rearward. Squeeze the two tabs of the quick release buckle to remove the tire sealant and compressor kit. To store the inflator kit, reverse the steps. To access the spare tire and tools: 1. Open the trunk. See 2.
  • Page 317 This vehicle will have either a coin/pierce jack (D) and a jack handle extension (C) or a hex head jack (B) and a jack lift assist tool (A). Place the tools next to the tire being changed. 5. Place the spare tire next to the tire being changed.
  • Page 318 2. Turn the wheel wrench counterclockwise once on each wheel nut to loosen it. Do not remove them yet. 3. Place the jack near the flat tire. 4. Place the wheel blocks on both sides of the tire at the opposite corner of the tire being changed.
  • Page 319 8. Position the jack lift head at the jack location nearest the flat tire. The location is indicated by a notch in the flange. The jack must not be used in any other position. Getting under a vehicle when it is jacked up is dangerous.
  • Page 320 Make sure the jack lift head notch is placed in the flange notch. Raise the vehicle far enough off the ground so there is enough room for the road tire to clear the ground. 10. Remove all of the wheel nuts. 11.
  • Page 321 Never use oil or grease on bolts or nuts because the nuts might come loose. The vehicle's wheel could fall off, causing a crash. 14. Reinstall the wheel nuts. Tighten each nut by hand until the wheel is held against the hub.
  • Page 322: Storage Compartments

    19. If this vehicle is the RS model, snap the jack cover back into place. 20. Remove the wheel blocks and return them to their proper storage location. When reinstalling the wheel cover or center cap on the full-size tire, tighten all five plastic caps hand snug with the aid of the wheel wrench and tighten them with...
  • Page 323 7. Turn the retainer nut clockwise until tight. 8. Replace the load floor. The load floor may not lay flat. The compact spare is for temporary use only. Replace the compact spare tire with a full-size tire as soon as you can. Reverse the instructions for removing the spare tire and tools to store the compact spare tire.
  • Page 324 For more information about the vehicle battery, see If the battery has run down, try to use another vehicle and some jumper cables to start your vehicle. Be sure to use the following steps to do it safely. Batteries can hurt you. They can be dangerous because: They contain acid that can burn you.
  • Page 325 with an automatic transmission, or with a manual transmission. 4. Turn the ignition to LOCK/OFF. Turn off all lights and accessories in both vehicles, except the hazard warning flashers if needed. An electric fan can start up even when the engine is not running and can injure you.
  • Page 326 7. Connect one end of the black negative ( ) cable to the negative ( ) terminal of the good battery (C). 8. Connect the other end of the black negative ( ) cable to the negative ( ) grounding point (D). 9.
  • Page 327: Towing

    Consult your dealer or a professional towing service if the disabled vehicle must be towed. To tow the vehicle behind another vehicle for recreational purposes, such as behind a motorhome, see Recreational Vehicle Towing in this section. Recreational vehicle towing refers to towing the vehicle behind another vehicle such as behind a motor...
  • Page 328 To dinghy tow the vehicle from the front with all four wheels on the ground: 1. Position the vehicle to tow and then secure it to the towing vehicle. 2. Shift the automatic transmission to P (Park) or a manual transmission into first gear and turn the ignition to LOCK/OFF.
  • Page 329 Tow the vehicle with the two rear wheels on the ground and the front wheels on a dolly: To tow the vehicle with two wheels on the ground and a dolly: 1. Put the front wheels on a dolly. 2. Shift the automatic transmission into P (Park) or a manual transmission into first gear.
  • Page 330 Always use waxes and polishes that are non-abrasive and made for a basecoat/clearcoat paint finish. Foreign materials such as calcium chloride and other salts, ice melting agents, road oil and tar, tree sap, bird droppings, chemicals from industrial chimneys, etc., can damage the vehicle's finish if they remain on painted surfaces.
  • Page 331 Rinse the vehicle well, before washing and after, to remove all cleaning agents completely. If they are allowed to dry on the surface, they could stain. Dry the finish with a soft, clean chamois or an all-cotton towel to avoid surface scratches and water spotting.
  • Page 332 The surface of these wheels is similar to the painted surface of the vehicle. Do not use strong soaps, chemicals, abrasive polishes, abrasive cleaners, cleaners with acid, or abrasive cleaning brushes on them because the surface could be damaged. Do not use chrome polish on aluminum wheels.
  • Page 333 Use a stiff brush with tire cleaner to clean the tires. If the vehicle is damaged and requires sheet metal repair or replacement, make sure the body repair shop applies anti-corrosion material to parts repaired or replaced to restore corrosion protection.
  • Page 334 Some weather and atmospheric conditions can create a chemical fallout. Airborne pollutants can fall upon and attack painted surfaces on the vehicle. This damage can take two forms: blotchy, ring-shaped discolorations, and small, irregular dark spots etched into the paint surface.
  • Page 335 Do not heavily saturate the upholstery while cleaning. Cleaners that contain solvents can damage the interior. Use a vacuum cleaner with a soft brush attachment to remove dust and loose dirt. A canister vacuum with rotating brushes in the nozzle may only be used on floor carpet and carpeted floor mats.
  • Page 336 to preserve and protect leather may permanently change the appearance and feel of the leather and are not recommended. Do not use silicone or wax-based products, or those containing organic solvents to clean the interior because they can alter the appearance by increasing the gloss in a non-uniform manner.
  • Page 337 If a floor mat is the wrong size or is not properly installed, it can interfere with the accelerator pedal and/or brake pedal. Interference with the pedals can cause unintended acceleration and/or increased stopping distance which can cause a crash and injury.

This manual is also suitable for:

Cruze - annexe 880 2011

Table of Contents