Page 1
® HDMI Splitters with EDID and Scaling 4K HDMI® Splitters with EDID and Scaling Part Numbers: EVSP12SC 1x2 EVSP14SC 1x4 www.vanco1.com • 800.626.6445...
Page 2
DEAR CUSTOMER Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference. This product is 100% inspected and tested in the United States to verify HDMI performance parameters.
FEATURES INTRODUCTION The Evolution by Vanco EVSP12SC and EVSP14SC HDMI splitters with 4K, 4:4:4, and HDR pass-through, splits one source signal to multiple displays. Both splitters are also able to downscale to 1080p, allowing 4K resolution to be maintained on other outputs. Also features EDID management, with different modes to ensure compatibility with source and display combinations.
Page 4
4K HDMI® 1x4 Spiltter with EDID and Scaling Part # EVSP14SC • Transmits audio and video from a single source to 4 displays up to 4K (2160p) Ultra High Definition resolution without any loss of quality or resolution • Supports 4K and 1080p resolutions simultaneously; downscales to 1080p for lower resolution displays while maintaining 4K on other outputs •...
SPECIFICATIONS HDMI Compliance ............HDMI 2.0a HDCP Compliance ............HDCP 2.2/1.4 Video Bandwidth ............600MHz/18Gbps Video Support ............HDR 4K@60Hz (4:2:0 10 bits)/ 4k@60Hz (4:4:4 8 bits) Audio Support ............DTS-HD Master Audio, Dolby TrueHD Dolby Digital, DTS, LPCM ESD Protection ............Human Body model: ±15kV (air-gap discharge) ±8 kV (contact discharge) Firmware Update ............
Page 6
PANEL DESCRIPTIONS EVSP12SC 1. Power LED: Illuminates when the splitter is connected to power 2. Micro-USB Port: Connect the included 5V DC power supply to power the unit 3. EDID MODE: Default EDID mode has been tested for compatibility with most source and display combinations, however to manually adjust EDID, see below for DIP Switch adjustments Dip Switch Position Description...
Page 7
PANEL DESCRIPTIONS EVSP14SC 1. Power LED: Illuminates when the splitter is connected to power 2. Micro-USB Port: Connect the included 5V DC power supply to power the unit 3. EDID MODE: Default EDID mode has been tested for compatibility with most source and display combinations, however to manually adjust EDID, see below for DIP Switch adjustments Dip Switch Position Description...
CONNECT AND OPERATE EVSP12SC HDTV HDTV HDMI HDMI HDMI Out 1 HDMI Out 2 HDMI Source In EVSP14SC HDTV HDTV HDTV HDMI HDMI HDMI Out 2 HDMI Out 3 HDMI Out 4 HDMI Out 1 HDMI HDMI Source In HDTV www.vanco1.com...
“Downloads tab” of this product on www.vanco1.com. Save the firmware file (.bin) & software in the same folder from the product page on the Vanco website Connect the Micro-USB cable to connect the splitter to a Windows based PC Open firmware update software and then device will start to update firmware automatically After update process is completed, the software will display a “Success”...
If repairs are needed during the warranty period the purchaser will be required to provide a sales receipt/sales invoice or other acceptable proof of purchase to the seller of this equipment. The seller will then contact Vanco regarding warranty repair or replacement.
TECHNICAL SUPPORT In case of problems, please contact Vanco Technical Support by dialing 1-800-626-6445. You can also email technical support issues to techsupport@vanco1.com. When calling, please have the Model Number, Serial Number (affixed to the bottom of the unit) and Invoice available for reference during the call.
Need help?
Do you have a question about the Evolution EVSP12SC and is the answer not in the manual?
Questions and answers