IHP PT Series Manual

PT SERIES PERIMETER TRIM KITS
[FOR USE WITH MODELS BRT2032, BRT2532/36, BRT4036/42, BRT4336/42, BRT4536/42, VRT3032/36/42, VCT3032/36/42, VRT4032/36, VCT4032/36, ALPHA32/36,
MISSION36/42, VEGA32/36/42, CUMBERLAND32/36/42, WESTERLY32]
KIT CONTENTS
1 ea. 3-Piece Trim Set
1 ea. Hardware Kit
1 ea. Instruction Sheet
Cat. No. Model
F1039 PT32 32" Perimeter Trim - Black
F1040 PT32B 32" Perimeter Trim - Brushed Brass
F1041 PT32P 32" Perimeter Trim - Platinum
F1042 PT36 36" Perimeter Trim - Black
F1043 PT36B 36" Perimeter Trim - Brushed Brass
F1044 PT36P 36" Perimeter Trim - Platinum
F1045 PT42 42" Perimeter Trim Kit, Black
F1046 PT42B 42" Perimeter Trim Kit, Brushed Brass
F1047 PT42P 42" Perimeter Trim Kit, Platinum
f i r e - p a r t s . c o m
REQUIRED TOOLS AND SUPPLIES
Flat Blade Screwdriver
GENERAL INFORMATION
3-piece perimeter trim kits are available in black, brushed brass
and platinum fi nishes.
READ ALL THE STEPS BEFORE STARTING THE INSTALLATION
THE FIREPLACE MUST BE OFF AND COLD BEFORE BEGINNING.
ALL WARNINGS, PRECAUTIONS AND INSTRUCTIONS IN THE
INSTALLATION AND OPERATION MANUAL PROVIDED WITH THE
APPLIANCE APPLY TO THESE INSTRUCTIONS.
If you encounter any problems, need clarifi cation of these instructions
or are not qualifi ed to properly install this kit, contact you local
distributor or dealer.
If any of these parts are missing or damaged, contact your dealer or
IHP.us.com for referral information.
INSTALLATION INSTRUCTIONS
NOTE: Firebox model may vary from that shown in Figure 2.
1. Remove packaging from three pieces of trim.
2. Locate the two adjusting plates with set screws and two shims
in the hardware packet.
3. Align shim under adjusting plate as shown in Figure 1.
4. Slide one end of adjusting plate/shim in slot on mitered edge of
top trim (see Figure 1).
5. Slide other end of adjusting plate/shim in slot on mitered edge
of side trim (see Figure 1).
IHP reserves the right to make changes at any time, without notice, in design, materials, specifi cations, prices and also to discontinue colors, styles and products. Consult your local distributor for
fi replace code information.
Printed in U.S.A. © 2014 Innovative Hearth Products
P/N 127149-01 Rev. B 03/2017
Description
IHP.us.com
P/N 127149-01
Rev. B, 03/2017
6. While fi rmly holding edges of trim together, tighten both screws
on the adjusting plate using a slotted screwdriver.
7. Repeat steps 2 through 6 for other side.
8. Place the assembled trim onto fi rebox cabinet. Align hanging
notches on trim with trim hanging shoulder screws (see Figure
2). Tap trim fi rmly into place with palm of hand or rubber mallet
by engaging hanging notches around shoulder screws. Start at
one end of the trim and work around fi rebox until all notches are
fully engaged.
Adjusting
Plate
Side Trim
Slot
Mitered Edge
Figure 1 - Assembling Trim
Assembled Trim
Figure 2 - Attaching Trim to Firebox
IHP
1508 Elm Hill Pike, Suite 108 • Nashville, TN 37210
HEARTH PRODUCTS
KITS AND ACCESSORIES
PT SERIES PERIMETER TRIM KITS
Set Screws
Top Trim
Shim
Mitered
Edge
Trim Hanging Shoulder
Screw Locations
Hanging Notches
on Trim
Slot
1