(intel i815ep chipset, s-370) atx form factor
main board (71 pages)
Summary of Contents for Acorp 7KTA1
Page 1
7KTA 1 User's Manual Version 1.0 The information presented in this publication has been carefully prepared to ensure reliability ; however, no responsibility is assumed for inaccuracies. Specifications are subject to change without notice. IBM, PC/AT, and PC/XT are tradem a rks of Interna- tional Business Machines Corporation.
Introduction System O v erview This m a nual was written to help you start using this product as quickly and s m o othly as possbile. Inside, you will find the answers to solve m o st proble m s . In order for this reference m a terial to be of greatest use, refer to the “expanded table of contents”...
1.Motherboard Description 1.1 Features 1.1.1 Hard w a re -Single AMD Socket 462 Athlon/Duron. -200MHz/266MHz Syste m Interface speed. Speed -Supports 33MHz PCI Bus speed. -Supports 4X AGP Bus. DRAM Memory -Supports 8/16/32/64..MB DIMM m o dule socket. -Supports Synchronous DRAM(3.3V) -Supports a m a xim u m m e m o ry size of 1.536GB with SDRAM.
Page 6
Flash Memory -Support flash m e m o ry. -support ESCD Function. IDE Built-in O n Board -Supports four IDE hard disk drives. -Supports PIO Mode 4, Master Mode,high perform a nce hard disk drives. -Support Ultra DMA 33/66/100 Bus Master Mode. -Supports IDE interface with CD-ROM.
1.1.2 Soft w a re BIO S -AWARD legal BIOS. -Supports APM 1.2. -Supports USB Function. -Supports ACPI O p eration System -Offers the highest perform a nce for MS-DOS,Windows, Windows NT, Windows 2000, Novell, OS/2, Windows95/98, Windows98SE, UNIX, SCO UNIX etc. 1.1.3 Attachments -HDD UDMA66/100 Cable.
1.2 Motherboard Installation 1.2.1 Layout of Motherboard FAN3 USB1 CO M 1 Printer Speak out Line in G A ME1 MIC in AMR SL O T AG P SLO T FAN2 PCI1 PCI2 PCI3 PCI4 BIO S PCI5 FAN1 ISA SL O T Chaosdr 1 Mnshdranarc Cdrbrhoshnn / 5 Chaosdr 1 Mnshdranarc Cdrbrhoshnn / 5 Chaosdr 1 Mnshdranarc Cdrbrhoshnn / 5...
1.3 Motherboard Connectors FAN3 USB1 CO M 1 Printer Speak out Line in G A ME1 MIC in AMR SLO T AG P SLO T FAN2 PCI1 PCI2 PCI3 PCI4 BIO S PCI5 FAN1 ISA SLO T 1.Babk Oandk I/O Cnnndbsnrr 1.Babk Oandk I/O Cnnndbsnrr 1.CC Atchn-In Cnnndbsnr 1.CC Atchn-In Cnnndbsnr...
1.3.1 Front Panel Connector(J1) J1 PANEL Connector PW_LED PW_BN HD_LED G _ LED EXTSMI SPKR Speaker Connector (SPK R ) An offboard speaker can be installed onto the m o therboard as a m a nufacturing option. An offboard speaker can be connected to the m o therboard at the front pannel connector.
ATX Power Switch (PW_BN) The system power is controlled by a m o m e ntary switch connected to this lead. Pushing the button once will switch the syste m ON. The syste m power LED lights when the syste m ' s power is on . Power LED Lead (PW_LED) The system power LED lights when the system power is on.
1.3.4 ATX 20-pin Po w e r Connector (PW1) This connector supports the power button on-board. Using the ATX power supply, functions such as Modem Ring Wake- Up and Soft Power Off are supported on this m o therboard . This power connector supports instant power-on functionality, which m e ans that the syste m will boot up instantly when the power connector is inserted on the board.
1.4 Back Panel Connectors Parallel (Printer) Port MIDI/(G A ME) Port (15-pin Female) (25-pin Female) PS/2 Mouse SPEAKER C O M 1 PS/2 Keyboard (6-pin Female) Serial Port(9-pin Male) LINE IN 1.4.1 PS/2 Mouse /Keyboard CO N N. The m o therboard provides a standard PS/2 m o use / Keyboard m i ni DIN connector for attaching a PS/2 m o use.
Page 14
Front Two USB Connectors: USB2 FAN3 USB1 CO M 1 Printer Speak out Line in G A ME1 MIC in AMR SLO T AG P SLO T FAN2 PCI1 PCI2 PCI3 PCI4 BIO S PCI5 FAN1 ISA SLO T USB 2 G N D G N D G N D...
1.5 Serial and Parallel Interface Ports This syste m co m e s equipped with two serial ports and one parallel port. Both types of interface ports will be explained in this chapter. The Serial Interfaces: CO M 1/CO M 2 The serial interface port is som e tim e s refered to as an RS- 232 port or an asynchronous co m m u nication port.
Page 16
FAN3 USB1 CO M 1 Printer Speak out Line in G A ME1 MIC in AMR SLO T AG P SLO T FAN2 PCI1 PCI2 CO M 2 PCI3 PCI4 BIO S PCI5 FAN1 ISA SLO T Parallel Interface Port Unlike serial ports, parallel interface ports have been standardized and should not present any difficulty interfacing peripherals to your system .
1.6 CPU Installation 1.6.1 CPU Installation Procedure: Socket 462 1. Pull the lever sideways away fro m the socket then raise the lever to a 90-degree angle. 2. Locate Pin 1 in the socket and look for the white dot or cut edge in the CPU.
1.6.2 CPU Clock Selection: SW1/JP4 FAN3 USB1 CO M 1 Printer Speak out Line in G A ME1 MIC in AMR SLO T AG P SLO T FAN2 PCI1 PCI2 PCI3 PCI4 (MH Z ) (MH Z ) BIO S PCI5 33.33 FAN1...
1.6.3 CPU Ratio Selection: SW2 FAN3 USB1 CO M 1 Printer Cknbk Speak out Line in G A ME1 Mtkshokhdr MIC in AMR SLO T AG P SLO T O o d n O o d n O o d n O o d n O o d n FAN2...
1.7 Jumper Setting A ju m p er has two or m o re pins that can be covered by a plastic ju m p er cap, allowing you to select different syste m options. FAN3 Connector FAN3 USB1 CO M 1 Printer Speak out Line in...
1.7.1 CPU/System Fan Connectors: Fan2 O h n O h n A r r h g n m d n s A r r h g n m d n s O h n O h n O h n A r r h g n m d n s A r r h g n m d n s A r r h g n m d n s...
1.7.5 CMO S Function Select: JP2 O h n O h n A r r h g n m d n s A r r h g n m d n s O h n O h n O h n A r r h g n m d n s A r r h g n m d n s A r r h g n m d n s...
1.9 Audio Subsystem FAN3 USB1 CO M 1 Printer Speak out Line in G A ME1 MIC in AMR SLO T AG P SLO T CDIN1 FAN2 PCI1 PCI2 PCI3 PCI4 BIO S PCI5 FAN1 ISA SLO T 1.9.1 CD Audio-In Connectors: CDIN1 Assignment Pin CDIN1 CD-R...
2. BIO S Setup Introduction This m a nual discussed the Award Setup program built into the ROM BIOS. The Setup progra m allows user to m o dify the basic syste m configuration. This special infor m a tion is then stored in battery-backed RAM so that it retains the setup infor m a tion when the power is turned off.
Page 26
APM Support This AWARD BIOS supports Version 1.1& 1 .2 of the Advanced Power Managem e nt(APM) specification.Power m a nagem e nt features are im p lem e nted via the System Managem e nt Interrupt(SMI). Sleep and Suspend power m a nagem e nt m o des are supported.
Page 27
K e ystroke Function Up arrow Move to previous item Down arrow Move to next item Left arrow Move to the ite m on the left( m e nu bar) Right arrow Move to the ite m on the right( m e nu bar) Main Menu: Quit without saving changes Subm e nus: Exit Current page to the next higher level m e nu...
2.1 Main Menu Once you enter AWARD BIOS CMOS Set up Utility, the Main Menu will appear on the screen. The Main Menu allows you to select fro m several setup function. Use the arrow keys to select am o ng the item s and press<Enter> to accept and enter the sub-m e nu.
Page 29
Advanced BI O S Features This setup page includes all the ite m s of the BIOS special enchanced features. Advanced Chipset Features This setup page includes all the ite m s of the Chipset special enchanced features. Integrated Peripherals This selection page includes all the item s of the IDE hard drive and Program m e d Input/Output features.
Page 30
Load O p timized Defaults These settings are m o re likely to configure a workable com p uter when som e thing is wrong. If you cannot boot the com p uter successfully, select the BIOS Setup options and try to diagnose the problem after the com p uter boots.
2.2 Standard CMO S Features This item in the Standard CMOS Setup Menu is divided into 10 categories. Each category includes no, one or m o re than one setup item s . Use the arrow keys to highlight the item and then use the <PgUp>...
Page 32
Main Menu Selections This table shows the selections that you can m a ke on the Main Menu. Item O p tions Description Date Month DD YYYY Set the syste m , date. Note that the ‘Day’ auto m a tically changes when you set the data.
Page 33
Item O p tions Description Halt On All Errors Select the situation in which you No Errors want the BIOS to stop the POST All, but Keyboard process and notify. All, but Diskette All, but Disk/Key Base Me m o ry N/A Displays the am o unt of conventional m e m o ry detected during boot up.
2.3 Advanced BI O S Features ◎ ◎ ◎ ◎ ◎ Figure 3. Advanced BI O S Features CMOS Setup Utility-Copyright(C) 1984-2001 Award Software Advanced BIOS Features Anti-Virus Protection Disabled Item Help CPU Internal Cache Enabled External Cache Enabled Menu Level CPU L2 Cache ECC Checking Enabled Q u ick Power O n Self Test...
Page 35
CPU Internal Cache These two categories speed up m e m o ry access. However, it depends on CPU/chipset design. Enabled(default) Enabled cache. Disabled Disabled cache. External Cache This fields allow you to Enable or Disable the CPU’S “Level 2” secondary cache. Caching allows better perfor m a nce.
Page 36
Swap Floppy Drive If the syste m has two floppy drives, you can swap the logical drive nam e assignm e nts. The Choices: Enabled, Disabled(default). Boot Up Floppy Seek Seek disk drives during boot up. Disabled speeds boot-up. The Choices: Enabled(default), Disabled. Boot Up NumLock Status Select power on state for Num l ock.
Page 37
Security O p tion This category allows you to lim i t access to the system and Setup, or just to Setup. System The syste m will not boot and access to Setup will be denied if the correct password is not entered in pro m p t.
2.4 Advanced Chipset Features This section allows you to configure the syste m based on the specific features of the installed chipset. This chipset m a nages bus speeds and access to system m e m o ry resources, such as DRAM and external cache. It also coordinates co m m u nications of the PCI bus.
Page 39
DRAM Timary by SPD The Choices: Enabled(default), Disabled DRAM Clock This ite m deter m i nes DRAM Clock following the CPU host clock . The Choices: 100(default), 133. SDRAM Cycle Length When synchronous DRAM is installed, the num b er of clock cycle of CAS latency depends on the DRAM ti m i ng.
Page 40
Video RAM Cacheable When enabled, the access to the syste m VGA RAM address is cached. The Choices: Diasbled(default), Enabled. A G P Aperture Size Select the size of the Accelerated Graphic Port(AGP) aperture. The aperture is a portion of the PCI m e m o ry address range dedicated for graphics m e m o ry address space.
Page 41
USB K e yboard Support Select Enabled if your system contains a Universal Serial Bus(USB) controller and you have a USB keyboard. The Choices: Disabled(default), Enabled. O n chip Sound The default setting of this item utilizes an onboard sound chip for audio output.
Page 42
PCI #2 Access #1 Retry The Choices: Enabled(default), Disabled. A G P Master 1WS Write When Enabled, write data to the AGP (Accelerated Graphic Port) that will be executed with one wait states. The Choices: Disabled(default), Enabled. A G P Master 1WS Read When Enabled, read data to the AGP (Accelerated Graphic Port) that will be executed with one wait states.
2.5 Integrated Peripherals ◎ ◎ ◎ ◎ ◎ Figure 5. Integrated Peripherals CMOS Setup Utility-Copyright(C) 1984-2001 Award Software Integrated Peripherals O n -Chip IDE Channel 0 Enabled Item Help O n -Chip IDE Channel 1 Enabled IDE Prefetch Mode Enabled Menu Level Primary Master PIO Auto...
Page 44
O n -Chip IDE Channel 0 Enabled(default) Enabled onboard 1st channel IDE port. Disabled Disabled onboard 1st channel IDE port. O n -Chip IDE Channel 1 Enabled(default) Enabled onboard 2nd channel IDE port. Disabled Disabled onboard 2nd channel IDE port. IDE Prefetch Mode The Choices: Enabled (default), Disabled.
Page 45
Primary Master UDMA Auto(default) BIOS will autom a tically detect the IDE HDD Accessing m o de. Disabled Disabled. Primary Slave UDMA Auto(default) BIOS will autom a tically detect the IDE HDD Accessing m o de. Disabled Disabled. Secondary Master UDMA Auto(default) BIOS will autom a tically detect the IDE HDD Accessing m o de.
Page 46
UART 2 Mode This item allows you to select which Infra Red(IR) function of the onboard I/O chip you wish to use. The Choices: Standard (default), SCR, ASKIR. IR Function Duplex This ite m allows you to select which Infra Red(IR) function of the onboard I/O chip you wish to use.
2.6 Power Management Setup The Power Managem e nt Setup allows you to configure your system to m o st effectively save energy while operating in a m a nner consistent with your own style of co m p uter use. ◎...
Page 48
Power Management This option allows you to set each m o de individually. When not disabled, each of the ranges are from 1 m i n. to 1 hr. except for HDD Power Down which ranges from 1 m i n. to 15 m i n.
Page 49
Video O f f O p tion This field deter m i nes when to activate the vedio off feature for m o nitor power m a nagem e nt. Video O f f Method This determ i nes the m a nner in which the m o nitor is blanked.
Page 50
Wake Up Events If you highlight the “Press Enter” next to the “Wake Up Events” label and then press the enter key, it will take you to a sub m e nu with the following options: VG A When set to On, any event occurring at a VGA port will awaken a syste m which has been powered down.
Page 51
Primary INTR When set to On(default), any event occurring at Prim a ry INTR will awaken a system which has been powered down. The following is a list of IRQ, Interrupt ReQuests, which can be exe m p ted m u ch as the COM ports and LPT ports above can.
2.7 PnP/PCI Configurations This section describes configuring the PCI bus syste m . PCI or Personal Com p uter Interconnect, is a system which allows I/O devices to operate at speeds nearing the speed of the CPU itself when co m m u nicating with its own special co m p onents.
Page 53
Reset Configuration Data The syste m BIOS supports the PnP feature so the syste m needs to record which resource is assigned and proceeds resources from conflict. Every peripheral device has a node, which is called ESCD. This node records which resources are assigned to it.
Page 54
The above settings will be shown on the screen only if “Manual” is chosen for the resources controlled by function. Legacy is the ter m , which signifies that a resource is assigned to the ISA Bus and provides for non-PnP ISA add-on cards.
Page 55
PCI / VG A Palette Snoop Choose Disabled or Enabled. Som e graphic controllers which are not VGA com p atible take the output from a VGA controller and m a p it to their display as a way to provide boot inform a tion and VGA com p atibility.
2.8 PC H e alth Status ◎ ◎ ◎ ◎ ◎ Figure 8. PC H e alth Status CMOS Setup Utility-Copyright(C) 1984-2001 Award Software PC Health Status Current CPU Temp. Item Help Current System Temp. Current CPU Fan Speed Menu Level Current Sys Fan Speed Vcore VDDQ...
2.9 Frequency / Voltage Control ◎ ◎ ◎ ◎ ◎ Figure 9. Frequency / Voltage Control CMOS Setup Utility-Copyright(C) 1984-2001 Award Software Frequency / Voltage Control Auto Detect DIMM / PCI CLK Disabled Item Help Spread Spectrum Modulated Disabled Clock By Slight Adjust Menu Level ←→↑↓: Move Enter:Select...
2.10 Load Fail-Safe Defaults When you press <Enter> on this item , you get a confir m a tion dialog box with a m e ssage si m i lar to: ◎ ◎ ◎ ◎ ◎ Figure 10. Load Fail-Safe Defaults CMOS Setup Utility-Copyright(C) 1984-2001 Award Software STANDARD CMO S FEATURES FREQ U ENCY/CLO C K CO N TRO L...
2.11 Load O p timized Defaults When you press <Enter> on this item , you get a confir m a tion dialog box with a m e ssage si m i lar to: ◎ ◎ ◎ ◎ ◎ Figure 11. Load O p timized Defaults CMOS Setup Utility-Copyright(C) 1984-2001 Award Software STANDARD CMO S FEATURES FREQ U ENCY/CLO C K CO N TRO L...
2.12 Set Supervisor / User Password ◎ ◎ ◎ ◎ ◎ Figure 12. Set Supervisor / User Password CMOS Setup Utility-Copyright(C) 1984-2001 Award Software STANDARD CMO S FEATURES FREQ U ENCY/CLO C K CO N TRO L ADVANCED BIO S FEATURES LO A D FAIL-SAFE DEFAULTS ADVANCED CHIPSET FEATURES LO A D O P TIMIZED DEFAULTS...
Page 61
Password Disabled If you select “Syste m ” at the Security Option of BIOS Features Setup Menu, you will be prom p ted for the password every ti m e when the syste m is rebooted, or any tim e when you try to enter Setup. If you select “Setup” at the Security Option of BIOS Features Setup Menu, you will be prom p ted only when you try to enter Setup.
2.13 Save & Exit Setup ◎ ◎ ◎ ◎ ◎ Figure 13. Save & Exit Setup CMOS Setup Utility-Copyright(C) 1984-2001 Award Software STANDARD CMO S FEATURES FREQ U ENCY/CLO C K CO N TRO L ADVANCED BIO S FEATURES LO A D FAIL-SAFE DEFAULTS ADVANCED CHIPSET FEATURES LO A D O P TIMIZED DEFAULTS INTEG R ATED PERIPHERALS...
2.14 Exit Without Saving ◎ ◎ ◎ ◎ ◎ Figure 14. Exit Without Saving CMOS Setup Utility-Copyright(C) 1984-2001 Award Software STANDARD CMO S FEATURES FREQ U ENCY/CLO C K CO N TRO L ADVANCED BIO S FEATURES LO A D FAIL-SAFE DEFAULTS ADVANCED CHIPSET FEATURES L O A D O P TIMIZED DEFAULTS INTEG R ATED PERIPHERALS...
Page 64
Date : Warranty Card/Technical Fault Report M/B Model No.: Vender Serial No. Date of Purchase: Hardw a re Configuration Used : RAM (Brand,MB ) Video Card Hard Drive O t her Card Diagnostic Soft w a re Used : Fault Description : 61 / Chapter 2 BIOS Setup 61 / Chapter 2 BIOS Setup 61 / Chapter 2 BIOS Setup...
Page 65
The 7KTA1 Mainboard layout FAN3 USB1 CO M 1 Printer Speak out Line in G A ME1 MIC in AMR SLO T AG P SLO T FAN2 PCI1 PCI2 PCI3 PCI4 BIO S PCI5 FAN1 ISA SLO T J1 PANEL Connector...