Download Print this page

Advertisement

Operating and installation instructions
Gas hobs
KM 2010 / 2011 / 2012 / 2013
KM 2030 / 2032 / 2033
KM 2050 / 2051
en - GB
To avoid the risk of accidents
or damage to the appliance it is
essential to read these
instructions before it is installed
and used for the first time.
M.-Nr. 07 181 150

Advertisement

   Also See for Miele KM 2010

   Summary of Contents for Miele KM 2010

  • Page 1

    Operating and installation instructions Gas hobs KM 2010 / 2011 / 2012 / 2013 KM 2030 / 2032 / 2033 KM 2050 / 2051 en - GB To avoid the risk of accidents or damage to the appliance it is...

  • Page 2

    Per questo se si vuole usare l’apparecchio in un paese diverso rivolgersi al servizio di assistenza tecnica Miele del paese in cui si intende usarlo.

  • Page 3

    Gas-heated appliances Safety precautions to take if you smell gas ß Turn off the gas emergency control valve immediately. This is usually located near the gas meter. ß Eliminate all sources of ignition in a safe manner. Do not smoke, light cigarette lighters or matches. ß...

  • Page 4: Table Of Contents

    Contents Guide to the appliance ..........5 Models .

  • Page 5: Guide To The Appliance

    Guide to the appliance Models KM 2010 / KM 2011 Large burner Controls: e Front right Small burner cd Medium burners f Rear right g Rear left h Front left...

  • Page 6

    Guide to the appliance KM 2012 / KM 2013 Wok burner Controls: e Front right Small burner cd Medium burners f Rear right g Rear left h Front left...

  • Page 7

    Guide to the appliance KM 2030 Wok burner Controls: e Front right Small burner cd Medium burners f Rear right g Rear left h Front left...

  • Page 8

    Guide to the appliance KM 2032 / KM 2033 Large burner Controls: f Front right Small burner cd Medium burners g Rear right h Middle Wok burner i Rear left j Front left...

  • Page 9

    Guide to the appliance KM 2050 / KM 2051 Wok burner Controls: f Front right Small burner g Rear right Large burner de Medium burners h Middle i Rear left j Front left...

  • Page 10: Burners

    Guide to the appliance Burners Wok burner Small, medium and large burners a Burner ring b Burner cap c Burner head d Burner base e Ignition safety device f Ignitor...

  • Page 11: Warning And Safety Instructions

    Keep these instructions in a safe the manufacturer and could be place and ensure that new users are dangerous. Miele cannot be held liable familiar with the content. Pass them for damage resulting from incorrect or on to any future owner.

  • Page 12

    Warning and Safety instructions Safety with children Packaging, e.g. cling film, polystyrene and plastic wrappings, This appliance is only intended for must be kept out of the reach of babies use by adults who have read these and young children. Danger of instructions.

  • Page 13

    Miele cannot be held liable for the supply by a suitably qualified and consequences of an inadequate competent electrician in strict earthing system (e.g.

  • Page 14

    H 05 V V-F (pvc insulated), available from the Miele Spare Parts Department.

  • Page 15

    Warning and Safety instructions Correct use Always use heat-resistant pot holders or gloves when working with a The appliance gets hot when in use hot appliance. Ensure that they do not and remains hot for quite a while after it come into contact with the flames.

  • Page 16

    If the hob is used for very long hob. Miele cannot be held liable for this periods of time additional ventilation of type of damage. the room may be necessary, e.g. by...

  • Page 17

    Warning and Safety instructions Spray canisters, aerosols and other inflammable substances must not be Miele cannot be held liable for stored in a drawer under the hob. Cutlery inserts must be heat-resistant. damage caused by non-compliance with these Warning and Safety Always ensure that food is instructions.

  • Page 18: Caring For The Environment

    Caring for the environment Disposal of the packing Disposal of your old appliance material Electrical and electronic appliances often contain materials which, if The transport and protective packing handled or disposed of incorrectly, has been selected from materials which could be potentially hazardous to are environmentally friendly for human health and to the environment.

  • Page 19: Before Using For The First Time

    Before using for the first time Please stick the extra data plate for the appliance supplied with this documentation in the space provided in the "After sales service" section of this booklet. Cleaning for the first time ^ Remove any protective foil and adhesive labels. ^ Clean all removable parts of the burners with a solution of warm water and a little washing-up liquid applied with a soft sponge.

  • Page 20: Operation

    Operation The control is used to ignite the burner and to regulate the strength of the flame. ßThe gas supply is turned off & Strong flame / Weak flame The burners can only be switched on by pressing in the appropriate control and turning it anti-clockwise, and switched off by turning the control clockwise.

  • Page 21: Regulating The Flame

    Operation In the event of a power cut If there is an interruption to the electricity supply the gas can be ignited with a match. ^ Press in the relevant control and turn it anti-clockwise to the large flame symbol. ^ Hold the control pressed in and light the burner with a match.

  • Page 22: Suitable Pans

    Suitable pans Burner Min. pan base diameter in cm Small burner Medium burner Large burner Wok burner Max. diameter at top of pan in cm Small burner Medium burner Large burner Wok burner – Refer to the chart above and ensure that the pan diameter falls within the minimum and maximum diameters given for the burner you are using.

  • Page 23

    Suitable pans – Remember when purchasing new pans that manufacturers usually refer to the diameter at the top of the pan in their documentation. – Use a pan lid whenever possible to minimise heat loss. When placing pans on the pan support(s) make sure you position them so that they cannot tip up.

  • Page 24: Safety Cut-out

    Safety cut-out This appliance is fitted with a thermoelectric ignition safety device which cuts off the supply of gas to a burner if the flame goes out, for example if food has boiled over, or if there was a sudden draught. ^ To use the burner again, turn the control clockwise to the "ß"...

  • Page 25: Cleaning And Care

    Cleaning and care For Miele branded and cleaning and conditioning products see “Optional accessories”. Do not use a steam cleaning appliance to clean this appliance. The steam could reach electrical components and cause a short circuit. – The appliance should be cleaned after each use. Allow the appliance to cool down to a safe temperature before cleaning.

  • Page 26

    Remove any soiling which applied with a soft sponge. comes into contact with the If necessary, you could use Miele ceramic and printed flame symbols straight stainless steel hob cleaner (see "Optional away. Soiling, particularly accessories") and the scouring pad on the...

  • Page 27

    Cleaning and care To assemble the small, medium and large burners ^ Place the burner head c onto the burner base d so that the ignition safety device e, the ignitor f and the retaining pins g fit into their respective holes in the burner head. ^ Position the burner cap b onto the burner head c so that the retaining pins fit into their respective recesses.

  • Page 28

    Cleaning and care To assemble the wok burner ^ Place burner head c onto burner base d so that the the ignition safety device e and the ignitor f extend through their respective holes in the burner head. ^ Replace the burner ring a. ^ Replace the burner cap b.

  • Page 29: Problem Solving Guide

    – the flame slits are dry and unblocked. – the mains fuse has tripped. If it has, contact a qualified electrician or the Miele Service Department. The gas can be lit with a match. (See “Use during a power cut”).

  • Page 30

    ... the ignitor on the burner does not spark. – check whether the mains fuse has tripped. If it has, contact a qualified electrician or the Miele Service Department. – Check whether food deposits have lodged themselves between the ignitor and the burner cap.

  • Page 31: Optional Accessories

    Optional accessories Miele offer a comprehensive range of useful accessories as well as cleaning and conditioning products for your appliance. These products can be ordered online at: or from Miele (see back cover for contact details) Cleaning products Ceramic and stainless steel hob cleaner...

  • Page 32: Safety Instructions For Installation

    Safety instructions for installation The electrical cable (and a flexible Fit the wall units and extractor hood gas connection pipe in countries where before fitting the hob to avoid applicable) must be installed in such a damaging the surface. way so that they do not come into contact with any moving kitchen parts The room in which the gas hob is (e.g.

  • Page 33

    Safety instructions for installation Safety distance above the hob When two or more appliances are installed together below a cooker hood, e.g. a gas hob and an induction hob combiset, which have different safety distances given in the installation instructions, you should select the greater distance of the two.

  • Page 34

    Safety instructions for installation Ideally the hob should be installed with plenty of space on either side. There may be a wall at the rear and a tall unit or wall at one side. On the other side, however, no unit or divider should stand higher than the hob (see illustrations).

  • Page 35: Appliance And Building-in Dimensions

    Appliance and building-in dimensions KM 2010 / KM 2011 / KM 2012 / KM 2013 5 2 0 6 5 0 ß R 4 8 0 - 4 9 2 1 7 1 9 6 a Front b Casing depth c Gas connection R 1/2"...

  • Page 36

    Appliance and building-in dimensions KM 2030 5 2 0 7 5 0 ß R 0 5 0 4 8 0 - 4 9 2 1 7 1 9 6 a Front b Casing depth c Gas connection R 1/2" ISO 7-1 (DIN EN 10226) d Mains connection box with mains connection cable, L = 2000 mm...

  • Page 37

    Appliance and building-in dimensions KM 2032 / KM 2033 5 2 0 7 5 0 ß R 0 5 0 4 8 0 - 4 9 2 1 7 1 9 6 a Front b Casing depth c Gas connection R 1/2" ISO 7-1 (DIN EN 10226) d Mains connection box with mains connection cable, L = 2000 mm...

  • Page 38

    Appliance and building-in dimensions KM 2050 / KM 2051 5 2 0 9 0 0 ß R 0 5 0 4 8 0 - 4 9 2 1 7 1 9 6 a Front b Casing depth c Gas connection R 1/2" ISO 7-1 (DIN EN 10226) d Mains connection box with mains connection cable, L = 2000 mm...

  • Page 39: Installation

    Installation Preparing the worktop Installing the hob ^ Make the worktop cut-out following ^ Feed the connection cable down the dimensions applicable. through the cut-out. Remember to maintain a minimum ^ Place the hob in the cut-out without safety distance from the back wall, securing it.

  • Page 40: Tiled Worktop

    Installation General installation tip Tiled worktop Grout lines a and the hatched area underneath the hob frame must be Do not use any sealant unless smooth and even. If they are not the expressly instructed to do so. The hob will not sit flush with the worktop sealing strip under the edge of the top and the sealing strip underneath the part of the appliance provides a...

  • Page 41: Electrical Connection

    Electrical connection Connection should be made via a All electrical work should be carried suitable isolator or a double pole fused out by a suitably qualified and spur connection unit which complies competent person, in strict with national and local safety accordance with current local and regulations and the on/off switch should national safety regulations (BS 7671...

  • Page 42

    If the connection cable is damaged, it must be replaced by a suitably qualified electrician with a special connection cable of type H 05 V V-F (pvc insulated), available from the Miele Service Department. The manufacturer cannot be held liable for damage which is the direct or indirect result of incorrect installation or connection.

  • Page 43: Gas Connection

    Please contact your dealer or the Miele Spare Parts Department for the Check with your local gas supplier appropriate conversion jets if about the type of gas and its necessary.

  • Page 44

    Gas connection Connection The gas connection must be installed so that connection can be made either from inside or outside the kitchen unit, and the isolating valve must be easily accessible and visible (by opening one of the kitchen doors, if necessary). After installing the appliance the gas burners have to be set for local conditions.

  • Page 45: Burner Ratings

    Burner ratings Nominal ratings for all gas types with the burner full on Burner Gas type KM 2010 / KM 2011 KM 2012 / KM 2013 / KM 2030 Small Natural gas burner Liquid gas Medium Natural gas 1.75 1.75...

  • Page 46

    Burner ratings Nominal rating at low setting Burner Gas type KM 2010 / KM 2011 KM 2012 / KM 2013 / KM 2030 Small Natural gas 0.25 0.25 burner Liquid gas 0.25 0.25 Medium Natural gas 0.35 0.35 burner Liquid gas 0.35...

  • Page 47: Conversion To Another Type Of Gas

    Conversion to another type of gas Connection to the gas supply, or conversion from one type of gas to another, should only be undertaken by an approved and registered gas installer in strict accordance with local and national safety and building regulations (e.g.

  • Page 48: Changing The Jets

    Conversion to another type of gas Changing the jets Small, medium and large burners Disconnect the gas hob from the electricity supply by switching off at the socket or by disconnecting the mains fuse. To change the main jets Small, medium and large burners The burner cap b and burner head c are locked in position.

  • Page 49: To Change The Small Jets

    Conversion to another type of gas To change the small jets (for all burners) The top of the appliance has to be removed before the small jets can be changed. ^ Loosen the fixing screws on the burners. ^ Pull the control knobs off. ^ Lift the top of the appliance off.

  • Page 50: After Changing The Jets

    Conversion to another type of gas After changing the jets ^ Reassemble the burner parts in the reverse order, ^ Check all gas fittings for leaks by operating the burner without the top section of the hob in place (use a match to ignite the flame).

  • Page 51: After Sales Service, Data Plate

    Please note that telephone calls may be monitored and recorded to improve our service. When contacting Miele, please quote the model and serial number of your appliance. These are given on the data plate. N.B. A call-out charge will be applied for service visits where the problem could have been resolved as described in these instructions.

  • Page 52

    Alteration rights reserved / 2111 M.-Nr. 07 181 150 / 06...

Comments to this Manuals

Symbols: 0
Latest comments: