Advertisement
SERVICE MANUAL
SPECIFICATION
Power source
Overall dimension(Net dimension)
Net weight
Power consumption
Motor output
Marked capacity of washing/spinning
Washing method
Water capacity
Pulsator speed
Spinner tub speed
Automatic Washer
AC 230V, 60Hz
570mmX600mmX985mm
39kg
420W/1500W
180W
11.5kg
Automatic reverse turn
75 Liters
60-190 rpm
700 rpm
WVIID1158BKG
1
Advertisement
Table of Contents
Related Manuals for Whirlpool WVIID1158BKG
Summary of Contents for Whirlpool WVIID1158BKG
- Page 1 SERVICE MANUAL Automatic Washer WVIID1158BKG SPECIFICATION Power source AC 230V, 60Hz Overall dimension(Net dimension) 570mmX600mmX985mm Net weight 39kg Power consumption 420W/1500W Motor output 180W Marked capacity of washing/spinning 11.5kg Washing method Automatic reverse turn Water capacity 75 Liters Pulsator speed...
-
Page 2: Abnormal Condition
Specification: Subject to change without notice. ABNORMAL CONDITION When the washer is abnormal, the washer stops as the every actions turns off, beep tone sounds ON-0.1 second and OFF-0.1 second for 6 seconds and number window LED display abnormal code. The washer judges the following six conditions as abnormal condition. 1) Abnormal condition of water supply In supplying with water, the water level does not reach extra low level within 10 minutes or does not reach your chosen water level within 20 minutes. - Page 3 7) Abnormal failure of main control and frequency conversion communication The digital tube displays the fault code "Ed2", accompanied by a whistle sound. • First check whether the reactor is in good contact • Replace the computer main control board 8) The display board cannot receive the main control signal.
- Page 4 Water temperature sensor failure EC2 The digital tube displays the fault code "EC2" • First check whether the connection between the main control board and the water temperature sensor is good • Replace the heating tube or the computer main control board to test whether the function is normal 16) Heating pipe failure E6C or E7C The digital tube displays the fault code "E6C"...
-
Page 5: Circuit Diagram
CIRCUIT DIAGRAM COLOR SYMBOL GRAY BLUE GREEN BLACK LIGHT BLUE BROWN ORANGE PINK WHITE YELLOW VIOLET THOUBLESHOOTING TROUBLE INSPECTION INSPECTION CAUSES REMEDY a. Power Source Is fuse blown? Any indications Deterioration of fuse. Replace. and beep do not Motor is defective. Replace. -
Page 6: Water Supply
TROUBLE INSPECTION INSPECTION CAUSES REMEDY b. Water Supply Water does not Does humming Something on the filter of flow when the noise come on the water valve or hose Clean the filter. power switch is from water joint assembly. start valve？... - Page 7 TROUBLE INSPECTION INSPECTION CAUSES REMEDY c. Wash/Rinse ’ Bearing ass y is defective. Replace. Washing cycle does Does the spin tub Poor connect of not start even if rotated normally Replace. connectors water keeps the when the Thermostat on motor is selected water level.
-
Page 8: Spin Drying
TROUBLE INSPECTION INSPECTION INSPECTION CAUSES REMEDY ’ Repair or replace. Drain takes time too Drain hose ass y is deformed. long. Hose is connected in the Repair. wrong way. Note: In draining, the water lever sensor can Note: In draining, the water level sensor can Hose is too long or position of Repair. - Page 9 TROUBLE INSPECTION INSPECTION INSPECTION CAUSES REMEDY Operation of safety device Start of spin-drying. Safety device work. Normal spin. Electric circuit works to stop Electric circuit spin when safety device counts operation detects continuously three of safety device. times of abnormal swing of spin drum.
- Page 10 TROUBLE INSPECTION INSPECTION CAUSES REMEDY Buzzing/rattling Does some noise Belt is slipping. Adjust. during washing sound during Pulley is loose. Tighten. or rinsing. spin drying? Some part touch motor Repair or replace Something underneath Remove. pulsator. ’ Pulsator is rubbing. Adjust bearing ass ’...
-
Page 11: Part List
PART LIST ’ 中文名称 Key No. Part No. Description 洗涤上盖组件 301B14A008444 Washer Lid Complete 螺钉盖 301B151300012 Screw Cap 螺钉 ST1TN40160UK- Screw 转轴座 左 A-4.1 301B15A001228 Left turn shaft seat 转轴座 右 A-4.2 301B15A001237 Right rotating shaft seat 膨松剂口盖 301B311600004 面架喷漆罩光完成 301B14A006861 Top Plate 螺钉盖... - Page 12 外桶盖 301B21A006858 Outer Tub Cover 螺钉 ST1TN40140SE- Screw 加热管支架 301G222900001 Heating pipe bracket 螺钉 ST1TN40120UK- Screw 外桶体 301B21A006879 Outer Tub Drum 溢水软管 301B32A006948 Overflow Hose 海绵套环 3012143414140 Cushion 软管卡簧 3012334002140 Hose Band 底栓 3012212202140 Drain Pipe 加热管 C-10 301B80A001596 Heating pipe 加热管线束...
- Page 13 滤波器安装板 D-15 301B41A005489 Filter mounting plate 六角螺母 D-16 SN2H1N80SE--- 螺钉 D-17 SFSPG40100SA- Screw 主控板 D-18 70C07292 Main control board Main control board box 主控板盒盖 D-19 301B80A008834 cover 螺钉 D-20 ST1TN40140SE- Screw Drive main control wiring 驱动主控线束 D-21 301B80A006308 harness 吊杆球座 D-22 3012234201140- Boom tee...
-
Page 14: Exploded View
ExplodedView...