Advertisement
SERVICE MANUAL
SPECIFICATION
Power source
Overall dimension(Net dimension)
Net weight
Power consumption
Motor output
Marked capacity of washing/spinning
Washing method
Water capacity
Pulsator speed
Spinner tub speed
Specification: Subject to change without notice.
Automatic Washer
AC 230V, 60Hz
540mmX568mmX955mm
34kg
400W/1500W
140W
10.5kg/9.5kg/8.5kg
Automatic reverse turn
65 Liters
60-190 rpm
700 rpm
WVIID1058BKG
WVWD1050BKG
WVWD950BKG
WVWD850BKG
1
Advertisement
Table of Contents
Related Manuals for Whirlpool WVIID1058BKG
Summary of Contents for Whirlpool WVIID1058BKG
- Page 1 SERVICE MANUAL Automatic Washer WVIID1058BKG WVWD1050BKG WVWD950BKG WVWD850BKG SPECIFICATION Power source AC 230V, 60Hz Overall dimension(Net dimension) 540mmX568mmX955mm Net weight 34kg Power consumption 400W/1500W Motor output 140W Marked capacity of washing/spinning 10.5kg/9.5kg/8.5kg Washing method Automatic reverse turn Water capacity 65 Liters...
-
Page 2: Abnormal Condition
ABNORMAL CONDITION When the washer is abnormal, the washer stops as the every actions turns off, beep tone sounds ON-0.1 second and OFF-0.1 second for 6 seconds and number window LED display abnormal code. The washer judges the following six conditions as abnormal condition. 1) Abnormal condition of water supply In supplying with water, the water level does not reach extra low level within 10 minutes or does not reach your chosen water level within 20 minutes. - Page 3 The digital tube displays the fault code "Ed2", accompanied by a whistle sound. • First check whether the reactor is in good contact • Replace the computer main control board 8) The display board cannot receive the main control signal. The digital tube displays the fault code "...
- Page 4 Water temperature sensor failure EC2 The digital tube displays the fault code "EC2" • First check whether the connection between the main control board and the water temperature sensor is good • Replace the heating tube or the computer main control board to test whether the function is normal 16) Heating pipe failure E6C or E7C The digital tube displays the fault code "E6C"...
-
Page 5: Circuit Diagram
CIRCUIT DIAGRAM WVIID1058BKG COLOR SYMBOL GRAY BLUE GREEN BLACK LIGHT BLUE BROWN ORANGE PINK WVWD1050&950&850BKG WHITE YELLOW VIOLET THOUBLESHOOTING TROUBLE INSPECTION INSPECTION CAUSES REMEDY a. Power Source Any indications Is fuse blown? Deterioration of fuse. Replace. and beep do not Motor is defective. -
Page 6: Water Supply
TROUBLE INSPECTION INSPECTION CAUSES REMEDY b. Water Supply Water does not Does humming Something on the filter of flow when the noise come on the water valve or hose Clean the filter. power switch is from water joint assembly. start valve？... - Page 7 TROUBLE INSPECTION INSPECTION CAUSES REMEDY c. Wash/Rinse ’ Bearing ass y is defective. Replace. Washing cycle does Does the spin tub Poor connect of not start even if rotated normally Replace. connectors water keeps the when the Thermostat on motor is selected water level.
-
Page 8: Spin Drying
TROUBLE INSPECTION INSPECTION INSPECTION CAUSES REMEDY ’ Repair or replace. Drain takes time too Drain hose ass y is deformed. long. Hose is connected in the Repair. wrong way. Note: In draining, the water lever sensor can Note: In draining, the water level sensor can Hose is too long or position of Repair. - Page 9 TROUBLE INSPECTION INSPECTION INSPECTION CAUSES REMEDY Operation of safety device Start of spin-drying. Safety device work. Normal spin. Electric circuit works to stop Electric circuit spin when safety device counts operation detects continuously three of safety device. times of abnormal swing of spin drum.
- Page 10 TROUBLE INSPECTION INSPECTION CAUSES REMEDY Buzzing/rattling Does some noise Belt is slipping. Adjust. during washing sound during Pulley is loose. Tighten. or rinsing. spin drying? Some part touch motor Repair or replace Something underneath Remove. pulsator. ’ Pulsator is rubbing. Adjust bearing ass ’...
-
Page 11: Part List
PART LIST ’ 中文名称 Key No. Part No. Description 洗涤上盖组件(WVIID1058BKG) 301B14A008503 Washer Lid Complete 洗涤上盖组件(WVWD1050&950&850BKG) 301B14A008514 Washer Lid Complete 螺钉盖 301B151300012 Screw Cap 螺钉 ST1TN40160UK- Screw 转轴座 左 A-4.1 301B15A001228 Left turn shaft seat 转轴座 右 A-4.2 301B15A001237 Right rotating shaft seat 膨松剂口盖... - Page 12 Screw 地线组件 3010856501140 Ground wire components 电源线组件 301B80A006976 Cord Assembly 电源线组件 301B80A005574 Cord Assembly 电源线束缚 3012152501140 Cord Stay 压接套管(WVIID1058BKG) D-10 3012871103140 Compressed Connector 压接套管(WVWD1050&950&850BKG) 压接套管(仅 WVIID1058BKG) D-11 3012871102140 Compressed Connector 线扣 D-12 3012152519140 Line deduction 导线束缚 D-13 3012152502140 Wire Stay...
- Page 13 集成滤波器(WVIID1058BKG) 70C72A0001655 Filter D-14 集成滤波器(WVWD1050&950&850BKG) E014181S00007 Filter 滤波器安装板 D-15 301B41A005489 Filter mounting plate 六角螺母 D-16 SN2H1N80SE--- 螺钉 D-17 SFSPG40100SA- Screw 主控板(WVIID1058BKG) D-18 70C07291 Main control board 主控板(WVWD1050&950&850BKG) 70C07289 Main control board 主控板盒盖(WVIID1058BKG) D-19 301B80A008834 Main control board box cover 主控板盒盖(WVWD1050&950&850BKG)
-
Page 14: Exploded View
ExplodedView...
Need help?
Do you have a question about the WVIID1058BKG and is the answer not in the manual?
Questions and answers
My washer has a problem.. when i try to use the spin. It doest open the drain. And then the pulsaror will turn without the tub turning.. only pulsator is spinning. The tub doesn't move.
The issue could be due to a defective brake lever assembly or a problem with the drain pump. If the pulsator spins but the tub does not move, the brake lever assembly may need to be replaced. Additionally, if the drain does not open during the spin cycle, check for foreign matter in the drain hose, a deformed valve bellow, disconnected pump lead wire, or a defective control circuit board. Repair or replace the faulty components as needed.
This answer is automatically generated