OPTEX FA D Series Instruction Manual

Photoelectric Sensor
D SERIES
Laser type
・DT- 4000□□(E)
・DR- 500□□(E)
・BGS-DL10□□(E)
・BGS-DL30□□(E)
・BGS-DL70□□(E)
INSTRUCTION MANUAL
Confirm if the item meets your needs.
●
Before the use, you should first thoroughly read
●
this manual and operate correctly as mentioned.
You should keep this manual at hand for proper use.
●
Input/Output circuit design
NPN
Protection circuit
PNP
Protection circuit
Parts name
Sensitivity setting volume
Light on/Dark on
*The tightening torque should be 0.5N・m or less.
Dimensions
unit: mm

Specifications

Model
Cable type
M8 connector type
Setting range
Supply voltage
Current consumption
Response time
Repeat accuracy *2
Light source
Receiver ： Output indicator（Orange)
Indicator
Emitter ： Laser emitter indication(Green)
Control output

Operation mode

Sensitivity adjustment
Ambient tem/ humid
Protect category/material
Weight
（Brown,①）
10~30V DC
（Black,④）
Control output
（Blue,③）
0V
（Brown,①）
10~30V DC
（Black,④）
Control output
（Blue,③）
0V
Laser emitter indication
Output indicator
＊For connector type only
Turn the connector as Black Arrow indicates,
otherwise you will damage the connector.
The damage will be unrepairable.
Through beam Retro reflection
type type
DT-4000 (N,P)-(E) DR-500 (N,P)-(E)
DT-4000C (N,P)-(E) DR-500C (N,P)-(E)
40 m 5m *1
40mA max. 30mA max.
0.5ms max.
0.5mm/20m 0.3mm/5m
Source pilot lamp（Green）
1-turn volume
IEC Standard IP67
cable type: about 66g
*2 in the vertical direction of optical axis (theoretical value)
＊1 with reflector P250F

Warnings

Laser beam
Pin configuration
○ This item utilizes visible light laser beam and is subject to safety standard
○ Must not stare into laser beam directly or reflection by mirror.
○ Must not disassemble.
Automatic stop function of laser emission is not equipped.
2 4
○ This product have already been registered at CDRH
1 3
10~30V DC
①
②
0V
③
Control output
④

Cautions

○ Warm-up period (apprx.100 msec.) must be secured.
○ Should avoid parallel wiring with high-voltage wire and/ or power line.
○ Avoid dust, oil and water adhesion to sensor forehead to escape
In case of adhesion, wipe with dustless cloth or lens cleaner.
○ In case of switching regulator, frame ground (FG) must be grounded.
Half-turn
connector
○ Use of controls or adjustments or performance of procedures other
○
Accurate type
BGS-DL10(N,P)-(E) BGS-DL30(N,P)-(E)
BGS-DL10C (N,P)-(E) BGS-DL30C (N,P)-(E) BGS-DL70C (N,P)-(E)
40～100mm
DC10 ～ 30V including 10% ripple (P-P)
0.2mm/100mm
Red Laser diode ６５０nm CLASS 2 (Ⅱ）
Max. 2mW
Output indicator（Orange LED) , Laser emitter indication (Green LED)
NPN/PNP open collector DC30V 100mA max.
Light ON / Dark ON Switchable
-10～40℃ / 35～95%
housing : heat-resistant ABS(antibacterial） lens : PC
/ connector type: about 20g
class 2(Ⅱ) of JIS C6802 as well as IEC and FDA regulations.
(Center for Devices and Radiological Health).
Never install in same conduit.
light's insulation and refraction.
than those specified herein may result in hazardous radiation exposure.
Don't bend the cable when the temperature of the cable or atmosphere
is below freezing.
！Must not use this item as safety equipment for the
purpose of human body protection.
！ Must not use this item as safety equipment for the
purpose of human body protection.
Specifications and equipment are subject to change
●
without any obligations on the part of manufacture.
For more information, questions and comments
●
regarding products, please contact us below.
→
http://www.optex-fa.com/rohs_cn/
Manufactured and sold by :
Manufactured and sold by :
OPTEX FA CO.,LTD.
Head office : 600-8815 Kyoto,Shimogyo,Awata Chudoji 93, Japan
Head office : 91 Chudoji-Awata-cho Shimogyo-ku Kyoto 600-8815 Japan
TEL +81-(0)75-325-2920 FAX +81-(0)75-325-2921
TEL +81-(0)75-325-2920
Website : http//www.optex-fa.com
BGS type
Longer type
BGS-DL70(N,P)-(E)
100～300mm 100～700mm
35mA max.
0.7ms max.
0.2mm/300mm 0.3mm/400mm
Max. 3mW
4-turn volume
FAX +81-(0)75-325-2921
0805370
0534868