FrSky Horus X12S-ISRM Manual

FrSky Horus X12S-ISRM Manual
Introduction
Thank you for purchasing the FrSky Horus X12S-ISRM digital telemetry radio system. In order to make the best use
of your system and to fly safely, please read this manual carefully. If you have any difficulties while using your
system, please consult the manual, your hobby dealer, or FrSky technical support.
Due to unforeseen changes in production, the information contained in this manual is subject to change without notice.
Meanings of Special Markings
Pay special attention to safety where indicated by the following marks:
DANGER- Procedures which may lead to dangerous conditions and cause death/serious injury if not carried
out properly.
WARNING- Procedures which may lead to a dangerous condition or cause death or serious injury to the user if
not carried out properly or procedures where the probability of superficial injury or physical damage is high.
CAUTION- Procedures where the possibility of serious injury to the user is small, but there is a danger of injury,
or physical damage, if not carried out properly.
= Mandatory = Prohibited
Warning: Always keep electrical components away from small children.
Charge/Alarm LED Diaplay Screen
SA, SB, SE, SF
Stick
(J3)
(J4)
PgUp, PgDn,
Joystick L1 L2
Speaker
Power Swich
Linear(L1, L2)
External Antenna Port for X12S-ISRM
Internal Antenna for X12S-ISRM
Slider
Trainer port
FrSky Electronic Co., Ltd. www.frsky-rc.com
Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: sales4tech@gmail.com
FrSky Horus X12S-ISRM Manual
Step 2: Configure the model channel and create the model name.
Model Setup Procedure-Internal Module
Step 1:
Choose the INT MODULE. Then turn ON INTERNAL RF, select the OUTSIDE or INSIDE ANTENNA ( Dual internal
antennas and external antenna work simultaneously while selecting the OUTSIDE ANTENNA.)
Set the Mode for TANDEM X20 internal RF corresponding to your receiver (ACCESS, ACCST D16).
FrSky Electronic Co., Ltd. www.frsky-rc.com
Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: sales4tech@gmail.com
Overview
(Switch Default Settings)
Earphone Port ● SA: 3 positions, Short Lever
SC, SD, SG, SH
● SB: 3 positions, Long Lever
● SC: 3 positions, Long Lever
● SD: 3 positions, Short Lever
● SE: 3 positions, Short Lever
S1, M-POS, S2
● SF: 2 positions, Long Lever
● SG: 3 positions, Short Lever
Stick
● SH: 2 positions, Momentary;
(J2)
Long Lever
(J1)
You can choose the Switch and define
Encoder
its positions in the Input and Output
SYS, MOL, TELE, RTN
Map screen.
Charge Jack
Digital Trim
Infinity 24 Antenna
Recommended 2.4GHz optional
high-gain antenna for achieving
higher performance and further
range.
Slider
+X
+Z
External RF
Module Slot
+Y
SMA Connector
USB Port
TF Card Slot
Contact us: frsky@frsky-rc.com
Touch the screen or use the navigation keys to enter the
RF system menu.
Contact us: frsky@frsky-rc.com
Version
1.1
Cautions on handling antenna of External Module
Do not touch the antenna during operation. Doing so could interfere with transmission, causing a crash.
Do not carry the transmitter by the antenna. The antenna wire could break and prevent transmission.
Do not pull the antenna forcefully. The antenna wire could break and prevent transmission.
Specifications
● Model Name: Horus X12S-ISRM
● Number of Channels: 16 channels (Up to 32 channels)
● Operating Voltage: DC9.6V
● Operating Temperature: -10~60℃
● Industrial screen: high resolution TFT (480*272), readable outdoor
● Compatibility: FRSKY A Series, D16 Series Receivers
● 16M Flash
* SD card is not supplied with X12S-ISRM Horus, please purchase separately.
Features
● Audio Speech Outputs (values, alarms, settings, etc.)
● Full telemetry and real-time data logging
● Antenna detection and SWR warning
● Integrated GPS module and 6-axis sensor (3-axis gyro and 3-axis accelerator)
● All CNC 6 ball bearings gimbals with accuracy hall sensor and extensible by stick ends
● Safe power switch with integrated strap base
● Two types trainer ports
● Inbuilt wireless trainer system
● 6 position encoder for easier flight modes switch
● FrSky FrTX operation system
● MP3 Player
● Industrial High Resolution TFT Screen Readable Outdoor
● Internal and External Antenna selectable
Notes and Warnings for Battery & Charger
The eight-cell NiMH battery is for use only in your Horus X12S-ISRM.
Be sure to use the built-in battery charger to charge the battery.
Be careful not to drop the battery.
Don't pull the battery wires as this could produce, short-circuits and cause the battery to explode.
Do not remove the battery from the Horus X12S-ISRM transmitter while the voltage warning is blinking as
this could cause internal settings and memories to be destroyed.
Be sure to turn off the Horus X12S-ISRM before charging the battery.
The Power Indicator LED will be on during charging, and be off after the charging is finished.
ETHOS Operating System
Create the model
Step 1: First go to System Settings, then click Model Select to select the model type.
FrSky Electronic Co., Ltd.
Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: sales4tech@gmail.com
Version
1.1
Step 2: Set the Channel Range
The TANDEM RF module supports 24 channels. the channel range is configurable, and it needs to be double
checked before use.
Step 3: Set the Receiver Number
Step 4 : Registration
In ACCESS model, select the STATE [Register] into Registration status on radio side. Then Press the F/S button
and power on your receiver, and select the "RX Name XX" and [REGISTER] to complete the Registration process
then power down the receiver.
Step 5: Automatic binding (Smart Match )
Move the cursor to Rx1[BIND],and select it, power your receiver, select the RX, and complete the process, the
system will confirm "Bind succeed". (Pressing the "F/S" button is not required in ACCESS to Bind. Please the
receivers manual for details).
FrSky Electronic Co., Ltd.
Add: F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: sales4tech@gmail.com
FrSky Horus X12S-ISRM Manual
www.frsky-rc.com Contact us: frsky@frsky-rc.com
FrSky Horus X12S-ISRM Manual
The system will assign you the receiver a number
automatically, when you create a new model, and this
can be easily changed. The range of the Model ID is
00-63, with the default number being 01. Once the
receiver is set to the desired number and is bound to the
TANDEM X20, the bind procedure will not need to be
repeated unless the receiver number is changed. At this
point, set the receiving number to your preferred
number and repeat the binding operation.
www.frsky-rc.com Contact us: frsky@frsky-rc.com
Version
1.1
Version
1.1