FrSky Horus X10 Manual
Introduction
Thank you for purchasing the FrSky Horus X10 digital telemetry radio system. In order to make the best use of your
system and to fly safely, please read this manual carefully. If you have any difficulties while using your system, please
consult the manual, your hobby dealer, or FrSky technical support.
Due to unforeseen changes in production, the information contained in this manual is subject to change without notice.
Meanings of Special Markings
Pay special attention to safety where indicated by the following marks:
DANGER- Procedures which may lead to dangerous conditions and cause death/serious injury if not carried
out properly.
WARNING- Procedures which may lead to a dangerous condition or cause death or serious injury to the user
if not carried out properly or procedures where the probability of superficial injury or physical damage is high.
CAUTION- Procedures where the possibility of serious injury to the user is small, but there is a danger of injury,
or physical damage, if not carried out properly.
= Mandatory
= Prohibited
Warning: Always keep electrical components away from small children.
SA, SB, SE, SF
SC, SD, SG, SH
LS
Stick
(J3)
(J4)
MDL,SYS,
RTN,TELE,
PgUp/PgDn,
Charge Jack
Diaplay Screen
Speaker
Power Swich
USB Port
Smart Port
FrSky Electronic Co., Ltd
www.frsky-rc.com
Add:F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: sales4tech@gmail.com
Step 1: Set the Mode for Horus X10 Internal RF
Refer to the table below and set the HORUS X10
to the mode corresponding to your receiver (D8,
D16 or LR12 ).
Mode of Horus X10
Compatible Receivers
V8-II series in D mode (V8FR-II,
V8R7-II, V8R4-II, VD5M, etc.)
D8
D series (D8R-II plus, D8R-XP,
D6FR, D4R-II, etc.)
D16
X series (X8R, etc.)
LR12
L series (L9R, etc.)
Note: older V8 receivers are not supported by the internal module but can be used with an external
DJT module in V8 mode.
Step 2: Set the Channel Range
The internal RF module of Horus X10 supports 47 channels. The channel range is configurable, and needs
double check before use.
Step 3: Set the Receiver Number
When you create a new model, the system will assign you a receiver number automatically, but this can be
easily changed. The range of the receiver number is 01-47, with the default number being 01. Once the receiver
is set to the desired number and is bound to the Horus X10, the bind procedure will not need to be repeated
unless the receiver number is changed, In this case, either set the receiver number to the previous one,
repeat the bind procedure.
Step 4: Bind
Bind refers to Horus X10 binding mode. Move the cursor to "STATE", press Encoder button, scroll the Encoder to
select "BIND" mode and then press Encoder button again, that the RF module has entered the bind mode. Then put
your receiver into binding mode and finish the bind procedure(refer to the receiver's manual for details).Press
"STATE" turn to "NORMAL" then exit.
Step 5: Set Failsafe mode
There are 3 failsafe modes When enabled :
No Pulse, Hold, Custom.
FrSky Electronic Co., Ltd
www.frsky-rc.com
Add:F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: sales4tech@gmail.com
Overview
(Switch Default Settings)
SA: 3 positions, Short Lever
SB: 3 positions, Long Lever
RS
S1, S2,
SC: 3 positions, Long Lever
Stick
SD: 3 positions, Short Lever
(J2)
SE: 3 positions, Short Lever
(J1)
SF: 2 positions, Long Lever
ENT
SG: 3 positions, Short lever
SH: 2 positions, Momentary;
Headset port
Long Lever
You can choose the Switch and define
its positions in the Input and Output
Map screen.
Trainer port
Contact us : frsky@frsky-rc.com
Number of Output Channels
47 channels
47 channels
47 channels
Contact us : frsky@frsky-rc.com
Cautions on handling antenna of External Module
Do not touch the antenna during operation. Doing so could interfere with transmission, causing a crash.
Do not carry the transmitter by the antenna. The antenna wire could break and prevent transmission.
Do not pull the antenna forcefully. The antenna wire could break and prevent transmission.
Specifications
Model Name: Horus X10
Number of Channels: 47 channels
Operating Voltage: DC 7.2V supplied by battery or DC 15V from adapter
Operating Temperature: -10~60℃
Industrial screen: high resolution TFT (480*272), readable outdoor
Compatibility: FrSky X series, D series, L series and V8-II series receivers (plus other receivers if an external module
is used)
16MB Flash
*SD card is not supplied with X10 Horus, please purchase separately.
Features
● Audio Speech Outputs (values, alarms, settings, etc.)
● Full telemetry and real-time data logging
● Antenna detection and SWR warning
● 6 ball bearings gimbals with accuracy hall
sensor and extensible by stick ends
● Inbuilt wireless trainer system
Notes and Warnings for Battery & Charger
The 2S Li-Ion battery is for use only in your Horus X10.
Be sure to use the offered battery charger to charge the battery.
Be careful not to drop the battery.
Don't pull the battery wires as this could produce, short-circuits and cause the battery to explode.
Do not remove the battery from the Horus X10 transmitter while the voltage warning is blinking as this could
cause internal settings and memories to be destroyed.
Be sure to turn off the Horus X10 before charging the battery.
The Power Indicator LED in the charger will be on during charging, and be off after the charging is finished.
Model Setup for Horus X10 Internal RF Module
The internal RF module of FrSky Horus X10 is newly developed by FrSky under the name of IXJT.
Enter the RF SYSTEM menu (for details, download it from FrSky website).
FrSky Electronic Co., Ltd
www.frsky-rc.com
Add:F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: sales4tech@gmail.com
● No Pulse: on loss of signal the receiver produces no pulses on any channel. To use this type, select it in the menu
and wait 9 seconds for the failsafe to take effect.
● Hold: the receiver continues to output the last positions before signal was lost. To use this type, select it in the menu
and wait 9 seconds for the failsafe to take effect.
● Custom: pre-set to required positions on lost signal. Move the cursor to the failsafe mode of channel and press Encoder,
then choose the Custom mode. Move the cursor to the channel you want to set failsafe on, and press Encoder.
Then rotate the Encoder to the place you want for failsafe and short press Encoder to finish the setting. Wait 9 seconds
before the failsafe takes effect.
Notice:
●
When failsafe is disabled on X10 Horus side, the failsafe set on receiver side will be used.
●
SBUS port always outputs, No Pulse could not perform properly on it. Set "Hold" or "Custom" for SBUS port.
●
The above instructions do not apply to D-series and L-series receivers, which require the internal RF module of
Horus X10 to be in D8 mode or LR12 mode. For these receivers, failsafe must be set on the receiver side
(see receiver instructions).
Step 6: Range
Range refers to Horus X10 range check mode.
A pre-flight range check should be done before
each flying session. Move the cursor to "STATE",
scroll the Encoder to select "RANGE" mode and
press Encoder.In range check mode, the effective
distance will be decreased to 1/30. Press "STATE"
turn to "NORMAL" then exit.
Model Setup for Horus X10 External RF Module
The external RF module can be powered on or off by
software. The setup process is the same as that for
the internal RF .
If you use other brand RF module than FrSky, please
choose PPM mode.
FrSky Electronic Co., Ltd
www.frsky-rc.com
Add:F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: sales4tech@gmail.com
● 6 position encoder for easier flight modes switch
● FrSky FrTX operation system
● Industrial High Resolution TFT Screen Readable
Outdoor
● Internal and External Antenna selectable
Contact us : frsky@frsky-rc.com
Contact us : frsky@frsky-rc.com
Need help?
Do you have a question about the Horus X10 and is the answer not in the manual?
Questions and answers
I'm looking to get into the channel set up for the model, I need the ailerons on 2 channels, and the elevators on 2 channels, I've seen the screen but this tx is totally new to me and I can't find my way around the programing
To set up the channel configuration for ailerons and elevators on the FrSky X10 transmitter:
1. Aileron Channels:
- Go to the relevant mix menu (e.g., "AIL-AIL4") where you can configure up to 4 aileron/flap channels.
- Use the “UP-DOWN” option to program deflection directions separately.
- Assign flight modes or switches if needed for different settings using the “SWITCH” option.
2. Elevator Channel:
- Use the “ELE” or “ELE2” options to represent the elevator channel.
- In the “ELEVATOR UP/DOWN” menu, set the travel range and its mix with the rudder if required.
- In the AILEVATOR menu, activate the mix by selecting “ACT” and adjust mix strength between elevator and aileron (-100% to +100%).
3. Flight Modes and Switches:
- Assign mixes to specific flight modes (e.g., LAUNCH, CRUISE, LANDING) or switches using the “SWITCH” setting.
4. Activation:
- Ensure the mix is turned on by selecting “ACT” in the corresponding menu.
5. Check Setup:
- Use the “Monitor” menu (accessed by holding “RTN”) to verify surface movement and endpoint settings.
Make sure to check surface travel and functionality after configuration to ensure safe operation.
This answer is automatically generated