If the package has suffered rough handling, bumps or damage (visible or concealed), please note it on the bill of lading before accepting the delivery and contact Omcan within 24 hours, so we may initiate a claim with the carrier. A detailed report on the extent of the damage caused to the machine must be filled out within three days, from the delivery date shown in the shipping documents.
Si el paquete ha sufrido un manejo de poco cuidado, golpes o daños (visible o oculto) por favor anote en la factura antes de aceptar la entrega y contacte Omcan dentro de las 24 horas, de modo que podamos iniciar una reclamación con la compañia.
Page 5
Safety and Warranty FOR YOUR SAFETY 1. Do not store or use gasoline or other flammable substances in the vicinity of this or any other appliance. 2. An LP cylinder not connected for use shall not be stored in the vicinity of this or any other appliance. Warning: For outdoor use only.
Page 6
1 YEAR PARTS AND LABOUR bench WARRANTY Within the warranty period, contact Omcan Inc. at 1-800-465-0234 to schedule a drop off to either an Omcan authorized service depot in the area, or to an Omcan Service warehouse to repair the equipment.
Technical Specifications Model PH-CN-0045 PH-CN-0045-S Stainless Steel 202 Powder-Coated Material Stainless Steel 202 Post and Base Thickness 26 GA Propane Tank Size 20 lbs. / 9.1 kgs. Base (Dia. x H) 18.1” x 3.4” / 460 x 86mm Tank Housing (Dia. x H) 14.9”...
Installation • The installation must conform to local codes, or in absence of local codes, with the standard for the storage and handling of liquid petroleum gases. • A dented, rusted or damaged propane tank may be hazardous and should be checked by your tank supplier.
Page 9
Installation STEP 2 • Put the post on the top of 3 pcs. post brackets. • Use 6 large bolts and flange nuts (M6) to connect the post to the 3 pcs. post brackets. Tighten the bolts and nuts. STEP 3 •...
Page 10
Installation STEP 4 • Remove the 4 bolts from the burner. • Put the gas hose through the post. • Fix the burner unit to the post by the 4 bolts. STEP 5 • Check whether the connection of vertical post and burner are assembled according to the instructions, and all bolts and nuts are tightened.
Installation STEP 6 • Fasten the reflector with 3 pcs. large flat washers and 3 pcs. wing nuts. STEP 7 • Bring up the tank housing and rest it on the post plate. • Connect the end thread of inlet gas hose to the regulator. •...
Operation 3. Press down the variable control knob and hold for 60 seconds. While holding down the variable control knob, press the igniter button several times until the pilot flame lights. Release the variable control knob after the pilot flame lights. 4.
Pilot light assembly is bent. Place pilot properly. Not in the correct location. Position properly and retry. If the appliance has any faults or problems during assembly or use, please don’t try to modify it yourself. Contact Omcan for assistance.
Parts Breakdown Model PH-CN-0045 46799 Model PH-CN-0045-S 47016...
Page 15
Parts Breakdown Model PH-CN-0045 46799 Model PH-CN-0045-S 47016 Item No. Description Position Item No. Description Position Item No. Description Position AG797 Reflector Panel for 46799, 47016 AG803 Stainless Steel Bolt for 46799, 47016 AG809 Wheel Kit for 46799, 47016 AG798...
Warranty Registration Thank you for purchasing an Omcan product. To register your warranty for this product, complete the information below, tear off the card at the perforation and then send to the address specified below. You can also register online by visiting: Merci d’avoir acheté...
Page 20
Since 1951 Omcan has grown to become a leading distributor of equipment and supplies to the North American food service industry. Our success over these many years can be attributed to our commitment to strengthen and develop new and existing relationships with our valued customers and manufacturers.
Need help?
Do you have a question about the PH-CN-0045 and is the answer not in the manual?
Questions and answers