DeWalt D25614 Manual page 8

English
the tool drill or chip faster and active vibration control will
not engage.
D WALT Tool Tag Ready (Fig. A)
e
Optional Accessory
Your hammer comes with mounting holes
for installing a D WALT Tool Tag. You will need a T15 bit tip to
e
install the tag. The D WALT Tool Tag is designed for tracking and
e
locating professional power tools, equipment, and machines
using the D WALT Tool Connect™ app. For proper installation of
e
the D WALT Tool Tag refer to the D
e
Lock‑On Switch (Fig. A)
Chipping mode only
The lock-on switch 7 offers increased comfort in extended use
applications. To lock the tool on, depress the lock-on switch
while the tool is running. The tool will continue to run after the
switch is released. To unlock and turn off the tool, depress and
release the switch.
Electronic Speed and Impact Control (Fig. A)
The electronic speed and impact control allows the use of
smaller drill bits without the risk of bit breakage, hammerdrilling
into light and brittle materials without shattering and optimal
tool control for precise chiselling.
To set the electronic speed and impact control dial
dial to the desired level. The higher the number, the greater
the speed and impact energy. Dial settings make the tool
extremely flexible and adaptable for many different appli cations.
The required setting depends on the bit size and hardness of
material being drilled.
• When chiselling or drilling in soft, brittle materials or when
minimum break-out is required, set the dial to a low setting;
• When breaking or drilling in harder materials, set the dial to
a high setting.
Overload Clutch
In case of jamming of a drill bit, the drive to the drill spindle is
interrupted. Because of the resulting forces, always hold the
tool with both hands and take a firm stance. After the overload,
release and depress the trigger to re-engage drive.
Mechanical Clutch
These tools are fitted with a mechanical clutch. The indication
that the clutch has activated will be an audible ratcheting
together with increased vibration.
Anti‑Rotation System
In addition to the clutch, an anti-rotation system offers increased
user comfort through an on-board, anti-rotation technology
capable of detecting if the user loses control of the hammer.
When a jam is detected, the torque and speed are stopped
instantly. This feature prevents self rotation of the tool.
The anti-rotation system indicator
indicate status.
6
and fasteners
11
WALT Tool Tag manual.
e
8 , turn the
9 will illuminate to
Anti‑Rotation System and Service Indicator LED
(Fig. A)
Your rotary hammer has two LEDs, indicating the Anti-rotation
system and a service indicator. Refer to the table for more
information on LED functionality.
lED Function
Red
(flashing)
Red
(permanently on)
Yellow
(permanently on)
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
Side Handle (Fig. A, B)

WARNING: To reduce the risk of personal injury, ALWAYS
operate the tool with the side handle properly installed.
Failure to do so may result in the side handle slipping
during tool operation and subsequent loss of control. Hold
tool with both hands to maximize control.
The side handle 13 clamps to the front of the gear case and
may be rotated 360˚ to permit right- or left-hand use.
Mounting the Straight Side Handle (Fig. B)
1. Widen the ring opening of the side handle
it counterclockwise.
2. Slide the assembly onto the nose of the tool, through the
steel ring 14 and onto the collar
and sleeve.
3. Rotate the side handle assembly to the desired position. For
hammerdrilling horizontally with a heavy drill bit, place the
side handle assembly at an angle of approximately 20° to
the tool for optimum control.
4. Lock the side handle mounting assembly in place by
securely tightening the handle
that the assembly will not rotate.
Description
lock-on/service
The red anti-rotation system
indicator LED 9 flashes if the
lock-on switch 7 is used in
any mode except the chipping
mode or if there is a fault with
the tool or the brushes have
completely worn out.
Anti-rotation system
Anti-rotation system is engaged.
Brush service
The yellow brushwear indicator
LED 10 lights up when the
carbon brushes are nearly worn
out, indicating that the tool
needs servicing within the next
8 hours of use.
13 by rotating
2 , past the chisel holder
13 rotating it clockwise so