DeWalt D25601-XE Instruction Manual
  1. Manuals
  2. Brands
  3. DeWalt Manuals
  4. Rotary Hammer
  5. D25601-XE
  6. Instruction manual

DeWalt D25601-XE Instruction Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
INSTRUCTION MANUAL
D25601-XE
45 mm (1-3/4") SDS MAX
COMBINATION HAMMER
®

Advertisement

Table of Contents
loading

Related Manuals for DeWalt D25601-XE

Summary of Contents for DeWalt D25601-XE

  • Page 1 INSTRUCTION MANUAL D25601-XE 45 mm (1-3/4") SDS MAX COMBINATION HAMMER ®...

  • Page 3: Definitions: Safety Guidelines

    1) WORK AREA SAFETY Definitions: Safety Guidelines a) Keep work area clean and well lit. Cluttered or dark areas invite accidents. b) Do not operate power tools in explosive atmospheres, such as in the The definitions below describe the level of severity for each signal presence of flammable liquids, gases or dust.

  • Page 4: Electrical Safety

    d) Remove any adjusting key or wrench before turning the power tool on. A performed. Use of the power tool for operations different from those intended wrench or a key left attached to a rotating part of the power tool may result in could result in a hazardous situation.
  • Page 5 Additional Safety Instructions for Rotary Hammers NOTE: Do not overheat the bit (discoloration) while grinding a new edge. Badly worn chisels require reforging. Do not reharden and temper the chisel. • Wear ear protectors. Exposure to noise can cause hearing loss. •...

  • Page 6: Markings On Tool

    WARNING: ALWAYS wear proper personal hearing protection that conforms to FIG. 1 CHISEL BIT ADJUSTMENT MODE AS/NZS1270 during use. Under some conditions and duration of use, noise from this product may contribute to hearing loss. WARNING: We recommend the use of a residual current device with a residual current rating of 30mA or less.
  • Page 7 Motor Electronic Speed and Impact Control (Fig. 1, 3) Your D WALT tool is powered by a D WALT-built motor. Be sure your power supply agrees with the nameplate markings. Voltage decrease of more than 10% will cause The electronic speed and impact control (G) offers the following advantages: loss of power and overheating.
  • Page 8 FIG. 2A FIG. 2B 1. Unscrew the side handle (C) and remove it from the front position. Leave the side handle mounting assembly in front position. 2. Screw the side handle directly into one of the rear side handle positions (I) on either side of the tool.

  • Page 9: Operation

    – when breaking or drilling in harder materials, set the dial to a high setting. 1. Rotate the mode selector switch (F) until it points towards the position. 2. Rotate the chisel in the desired position. FIG. 3 FIG. 4A 3.

  • Page 10: Maintenance

    FIG. 6 7. Stop the tool and remove the centerdrill. Place the core bit back into the hole and Proper Hand Position (Fig. 6) continue drilling. WARNING: To reduce the risk of serious 8. When drilling through a structure thicker than the depth of the core bit, break personal injury, ALWAYS use proper hand away the round cylinder of concrete or core inside the bit at regular intervals.

  • Page 11: Maximum Capacity

    30 days for a MAXIMUM CAPACITY replacement unit or a full refund. D25601-XE FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing, call (AUS) 1800 654 155 or (NZ) 0800 339258 for a free replacement.
  • Page 12 WALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286 • 20 Fletcher Road, Mooroolbark, VIC 3138 Australia (JUN10) Part No. N081421 D25601-XE Copyright © 2010 D WALT The following are trademarks for one or more D WALT power tools: the yellow and black color scheme; the “D” shaped air intake grill; the array of pyramids on the handgrip;...

Table of Contents