Related Manuals for Ferno 24.MAXX
Summary of Contents for Ferno 24.MAXX
- Page 1 Users’ Manual Mortuary Cots 24•MAXX , 24•miniMAXX , 24H•miniMAXX ® ® ® Read this Manual May 2011 GLO and Retain for Pub. No. 234-3307-04 Future Reference...
-
Page 2: Ferno Technical Support
Serial Number _________________________ all OTher lOCaTiOns Location: Crosstube at loading end of cot. For assistance or information, please contact your Ferno distributor. If you do not have a Ferno distributor, please contact Ferno Customer Relations: Users’ ManUal Ferno-Washington, Inc. To request additional free users’ manuals,... -
Page 3: Table Of Contents
9.4 Parts List 24-miniMAXX,24H-miniMAXX ___ 30 Training Record ______________________________ 31 5.4 Mattress _______________________________ 14 5.5 Wheel Locks ___________________________ 14 Maintenance Record ___________________________ 31 5.6 Sidearms (Optional) _____________________ 14 5.7 Side-Lift Handles (Optional) ______________ 15 © Ferno-Washington, Inc 234-3307-04 May 2011... -
Page 4: -Safety Information
Ferno-Washington, Inc. strongly recommends that only Ferno-manufactured cots be used in Ferno-manufactured cot improper parts and service can cause injury. Use only Ferno parts and Ferno-approved service on the cot. fasteners, and that only Ferno-manufactured cot fasteners be used for securing Ferno-manufactured cots in vehicles. -
Page 5: Safety And Instruction Labels
1.6 symbol glossary The symbols defined in this section are used on the cot and/or in this users’ manual. Ferno uses symbols recognized by the International Standards Organization (ISO), the American National Standards Institute (ANSI), and the mortuary services industry. -
Page 6: Operator Skills And Training
After the loading-end legs unfold, test that they have locked by pushing them against the bumper — the legs should not fold. If they do, lift the cot high enough to allow both sets of legs to unfold completely and lock. © Ferno-Washington, Inc 234-3307-04 May 2011... -
Page 7: About The Cot
Inspect the cot if the load limit has The cot is for professional use by one or more trained been exceeded (See Inspecting the operators. The cot is designed for use with a Ferno Model ® Cot, page 26). -
Page 8: Components
(above, right). Mattress (Bottom Side Shown) Users’ ManUal To request additional free users’ manuals, contact Ferno Customer Relations, your Ferno distributor, or visit www.ferno.com. Restraints (Set of 2 Included) © Ferno-Washington, Inc 234-3307-04 May 2011... -
Page 9: Specifications
Measurements number. Metric conversions are calculated before rounding the Imperial measurements. For more information, contact Overall Frame Length Ferno Customer Relations (page 2) or your Ferno distributor. Bed Surface Length Ferno reserves the right to change specifications without notice. -
Page 10: Cot Positions
3. Attach the mattress, restraints, and any accessories before placing the cot in service. Follow installation instructions in the restraint and accessory manuals, and the restraint-placement information in this manual Figure 1 - Securing the Footrest (page 11 and page 12). © Ferno-Washington, Inc 234-3307-04 May 2011... -
Page 11: Using The Features
Sidearm Mounts Sidearm Mounts Here if Used Here if Used Restraint Slot Restraint Slot Restraint Slot Restraint Slot Sidearm Mounts Sidearm Mounts Here if Used Here if Used Figure 2 - Restraint and Accessory Slots © Ferno-Washington, Inc 234-3307-04 May 2011... -
Page 12: Restraints
(Figure 4). To attach, use, and maintain restraints, see the restraint users’ manuals included with the restraints. Additional free manuals are available from Ferno Customer Relations (page 2). The cot bed panel has four slots for use with the two restraints provided (see Figure 2 on page 11). -
Page 13: Control Handles
See the Loading Height reference points on page 9. Operator-end Leg Control Loading-end Leg Control Handle (Red) Handle (Black) Used to Load Cot Only Figure 6 - Operator-End Control Handles © Ferno-Washington, Inc 234-3307-04 May 2011... -
Page 14: Mattress
To raise, rotate the sidearm upward until the pin locks in place. important Sidearms are not designed for lifting. Grasp only the main frame or (accessory) side lift handles to lift the cot. Figure 9 - Pulling the Sidearm Release Pin © Ferno-Washington, Inc 234-3307-04 May 2011... -
Page 15: Side-Lift Handles (Optional)
At the loading-end and operator ends of the cot, ● interference with cot structures limits the handle to only one storage position (see below). Figure 10 - Using the Side Lift Handle Figure 11 - Unfolding the Handle © Ferno-Washington, Inc 234-3307-04 May 2011... -
Page 16: Using The Cot
Confirm that the cot operates properly. Follow the ● instructions in Inspecting the Cot, page 26. The vehicle must have a Ferno cot fastener installed. ● Read the Users’ Manual Cot May Be Operated 6.2 general guidelines for Use... -
Page 17: Changing Cot Levels With Two Operators
Figure 14 - Work Together and Use Coordinated Movements © Ferno-Washington, Inc 234-3307-04 May 2011... -
Page 18: Changing Cot Levels With One Operator
6. Release the control handle and verify that the loading- end leg has locked in the new position. 7. Repeat Steps 1-6 as needed until the cot is level and at Figure 16 - Raise the Operator End First the desired height. © Ferno-Washington, Inc 234-3307-04 May 2011... -
Page 19: Rolling The Cot
See Using Additional Help, page 24 for recommended placement of operators and helpers. ote: Although the swivel wheels are only at the operator end, steering may be easier from the loading end under certain circumstances. Follow your mortuary protocols. © Ferno-Washington, Inc 234-3307-04 May 2011... -
Page 20: Transferring The Body Onto The Cot
For a list of accessories, see page 28. ote: Ferno recommends that you position the body with the head at the operator end of the cot, if possible. This orientation will place the body in a ‘heads-up’ position if you need to tilt the cot in a confined area (see “Maneuvering... -
Page 21: Loading The Cot
Operator-End Leg legs fold. Keep your hands nearer the Control Handle center of the cot when loading it into a vehicle. Figure 23 - Loading the Operator-End Legs © Ferno-Washington, Inc 234-3307-04 May 2011... -
Page 22: Unloading The Cot
Model 24H-miniMAXX: After the cot has been the operator and helpers to lift the cot higher than unloaded, lower the loading end of the cot to a level normal in order to allow the legs to lock. rolling position. © Ferno-Washington, Inc 234-3307-04 May 2011... -
Page 23: Loading Or Unloading With Two Trained Operators
The right-side operator does not use a control handle. ● If more than two operators or helpers are present, see Using Additional Help, page 24 for recommended placement of operators and helpers. © Ferno-Washington, Inc 234-3307-04 May 2011... -
Page 24: Using Additional Help
Maintain Inspect the cot if the load limit has control of the cot, operate the controls, and direct been exceeded (See Inspecting the all helpers. Cot, page 26). © Ferno-Washington, Inc 234-3307-04 May 2011... -
Page 25: Maintenance
When using maintenance products, follow the manufacturers’ Minimum directions and read the manufacturers’ material safety data Maintenance intervals sheets. You can purchase a recommended disinfectant from your Ferno distributor or Ferno Customer Relations (page 2). • Disinfecting (this page) • Cleaning (this page) 7.2 Disinfecting and Cleaning... -
Page 26: Waxing The Cot
Are restraint buckles free of visible damage and do ● they operate properly? Do installed accessories operate properly without ● interfering with cot operation? Is the vehicle properly prepared for the cot with an ● approved Ferno cot fastener installed? © Ferno-Washington, Inc 234-3307-04 May 2011... -
Page 27: Lubricating The Cot
I-Beam White lithium grease Steel Rod (inside leg-return spring) WRL-191-S or EZ-1 synthetic lubricant Leg Joints WRL-191-S or EZ-1 synthetic lubricant Wheels (sealed bearings) Do not lubricate Upper Leg Pivot Points Do not lubricate © Ferno-Washington, Inc 234-3307-04 May 2011... -
Page 28: Accessories
9.1 U.s.a. and Canada 9.2 Worldwide In the United States and Canada, to order parts or for To order Ferno parts, and for professional cot repair, contact professional cot repair, contact EMSAR - the only agent your Ferno distributor. Your distributor is the only agent ®... -
Page 29: Parts List 24-Maxx
Caster assembly w/brake 190-2090 J-leg bumper, screw, washer 190-1144 6" wheel and hub w/bearings 190-2091 J-leg bumper, mount, and hardware 090-5798 Swivel wheel fork, no wheel, w/bearing and pin 1 090-3376 Scuff strips, operator-end leg w/hardware © Ferno-Washington, Inc 234-3307-04 May 2011... -
Page 30: Parts List 24-Minimaxx,24H-Minimaxx
Red release handle w/hardware 090-0983 Control bar spring 090-0560 Crutch tip w/inserts (pair, Serial Numbers before 11N183015) 190-2090 J-leg bumper, screw, washer 190-2091 J-leg bumper, mount, and hardware 190-1510 Label Set 9 10 11 © Ferno-Washington, Inc 234-3307-04 May 2011... -
Page 31: Training Record
24•MAXX®, 24•miniMAXX®, 24H•miniMAXX® Training reCOrD Date Name Training Method MainTenanCe reCOrD Date Maintenance Performed © Ferno-Washington, Inc 234-3307-04 May 2011...