HUBBELL LIGHTING DUAL LITE EVHC Series Installation Instructions

Automatic Tests
The unit will automatically initiate a self-test/self-diagnostic
cycle based on the following table:
Testing Period
Once a month
Installing the Unit: Final Assembly
Once every
6 months
1. Align housing slots over tabs on backplate.
2. Pivot housing and snap closed.
3. Aim the lamps. Do not press on the lenses.
Manual Tests
Using the unit test switch, users can initiate different
duration test cycles based on the following table:
Initiating Action
Press test switch once
Press test switch twice
Pressing the test switch any time after a 90 minute test
cycle has begun cancels the remainder of the 90 minute
test and returns the unit to normal operation.
SERVICE/MAINTENANCE
Service / Maintenance
Maintenance
SERVICE /MAINTENANCE
This emergency lighting unit should be tested and maintained in accordance with National Electrical Code and NFPA 101 Life Safety
Code requirements. It is recommended that emergency light fixtures be tested for 30 seconds once a month and for 90 minutes once a
year.
Taking A Unit Out Of Service
If a unit is to be deliberately taken out of service for an extended period, the battery lead connector should be disconnected from the
charger circuit board and insulated so that the battery will go into storage in a fully charged condition.
Replacing The Battery
1. De-energize the AC power.
2. Disengage the housing cover from the backplate.
3. Disconnect the battery leads from the charger circuit board.
3. Disconnect the battery harness from the charger pcb.
4. Remove the battery from the clips inside the cover.
4. Disconnect the battery strap and remove battery pack.
5. Replace with a new battery (see unit model label for correct part number) and reconnect leads.
5. Replace with a new battery (see unit model label or battery label for correct part number) and reconnect harness.
3. Disconnect the battery harness from the charger pcb.
6. Reassemble cover to backplate.
4. Disconnect the battery strap and remove battery pack.
3. Disconnect the battery harness from the charger pcb.
Replacing LED Lamps
4. Disconnect the battery strap and remove battery pack.
The LED lamps inside the unit are not replaceable or field serviceable. Please see dual-lite.com for further assistance.
Troubleshooting
Emergency circuit does not work
• Batteries are shipped uncharged and disconnected. Connect battery leads and charge 24 hours before testing.
• Batteries are shipped uncharged, please charge for 24 hours before testing.
• Make sure the charger board and test button/light pipe are properly seated and aligned.
• Make sure the switch pcb and the button/light pipe is correctly seated and aligned.
• Check wiring connections.
• Check wiring connections.
Batteries are shipped uncharged, please charge for 24 hours before testing.
Make sure the switch pcb and the button/light pipe is correctly seated and aligned.
Batteries are shipped uncharged, please charge for 24 hours before testing.
Make sure the switch pcb and the button/light pipe is correctly seated and aligned.
RECYCLING INFORMATION
All steel, aluminum, and thermoplastic parts are recyclable. RECYCLING INFORMATION
All steel, aluminum and thermoplastic parts
NOTICE: Emergency units contain rechargeable batteries which
must be recycled or disposed of properly.
NOTICE: Emergency units contain rechargeable batteries which
must be recycled or disposed of properly.
Hubbell Lighting, Inc. Life Safety Products • www.dual-lite.com
Hubbell Lighting, Inc. Life safety Products • www.dual-lite.com
Copyright © Hubbell Lighting, Inc., All Rights Reserved • Specifications subject to change without notice. • Printed in U.S.A.
Copyright© Hubbell Lighting, Inc., All rights reserved • Specifications subject to change without notice.
OPERATION
OPERATION
OPERATION
Duration of Test
1 minute
Alternating:
30 minutes or 60 minutes
Test Cycle
1 minute
90 minutes
SERVICE /MAINTENANCE
Dual-Lite.com for further assistance.
Dual-Lite
Dual-Lite
are recyclable.
93049114 1 10/13
93049114 1 10/13
93049114_F 5/15
Printed in U.S.A.
IMPORTANT SAFEGUARDS
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should
When using electrical equipment, basic safety precautions
always be followed including the following.
should always be followed, including the following:
READ AND FOLLOW ALL SAFETY
READ AND FOLLOW ALL SAFETY
1. Do not use outdoors.
2. Do not let power supply cords touch hot surfaces.
1. Do not use outdoors.
3. Do not mount near gas or electric heaters.
2. Do not let power supply cord touch conductive surfaces.
4. Equipment should be mounted in locations and at heights where it will not readily be subject
3. Do not mount equipment near gas or electric heaters.
to tampering by unauthorized personnel.
4. Equipment should be mounted in locations and at heights where it will not readily be subject
5. The use of accessory equipment not authorized by the manufacturer may cause an
to tampering by unauthorized personnel.
unsafe condition.
5. The use of accessory equipment not authorized by the manufacturer may cause an unsafe
6. Do not use this equipment for other than its intended purpose.
condition.
7. Servicing of this equipment should be performed by qualified service personnel.
6. Do not use this equipment for other than its intended purpose.
8. Test cycling: the Life Safety Code (NFPA 101) requires testing of emergency lighting units once a month for a
7. Servicing of this equipment should be performed by qualified service personnel.
minimum of 30 seconds, and once a year for a minimum of 90 minutes.
8. Test cycling: the Life Safety Code (NFPA 101) requires testing of emergency lighting units
once a month for a minimum of 30 seconds, and once a year for a minimum of 90 minutes.
SEE UNIT LABEL FOR ADDITIONAL MODEL SPECIFICATIONS
•SEE UNIT LABEL FOR ADDITIONAL MODEL SPECIFICATIONS
SAVE THESE INSTRUCTIONS FOR USE BY OWNER/OCCUPANT
•SAVE THESE INSTRUCTIONS FOR USE BY OWNER/OCCUPANT
WARNING – This product contains chemicals known to the State of California to cause cancer, birth
WARNING – This product contains chemicals known to the state of California to cause cancer, birth
defects and/or other reproductive harm. Thoroughly wash hands after installing, handling, cleaning, or
defects and/or other reproductive harm. Thoroughly wash hands after installing, handling, cleaning, or
otherwise touching this product.
otherwise touching this product.
93051469
93051470
Emergency Lighting Equipment For Use in Damp Locations
93050644
93051471
93051469
93051472 Damp location listed units are suitable for installation in:
Emergency Lighting Equipment For Use In Damp Locations
93051470 93050644
93052054
93051471
93051469 1. Interior locations subject to moderate degrees of moisture, such as some basements, some barns,
93054690
93051472
93051470
93055110
93051841 Damp location listed units are suitable for installation in:
93051471 some cold storage
93052054
93051472
1. Interior locations subject to moderate degrees of moisture, such as some basements, some barns,
93051841 warehouses, and the like.
93052054
some cold storage warehouses, and the like.
2. Partially protected locations under canopies, marquees, roofed open porches and the like.
2. Partially protected locations under canopies, marquees, roofed open porches and the like.
EVHC Series
Twin-Head LED Emergency Lighting Unit
Standard, Remote, and Spectron
Installation, Operation, and Service Instructions
Twin-Head LED Emergency Lighting Unit
Standard, Remote, and Spectron® Equipped Models
Installation, Operation, and Service Instructions
93051469
INSTRUCTIONS
INSTRUCTIONS
INSTALLER:
INSTALLER:
EVHC Series
EVHC Series
®
Equipped Models
93051469
93051469