Playback Connection; Setting The Tv To The Av-Channel; Setting The On-Screen Language - Toshiba SD-25VLSR Service Manual

Dvd video player & vhs video cassette recorder

Table of Contents

Playback connection

The exact arrangement you use to interconnect various video and audio components to the DVD/VCR is dependent

on the model and features of each component. Check the Owner's Manual provided with each component for the

location of SCART socket.

Connection to a Satellite Receiver

If a Satellite Receiver is used, we recommend the following configuration:

Satellite

Antenna

Satellite

Receiver

SCART-cable (not

supplied)

SCART-cable (not supplied)

To record from Satellite Receiver press AUX on the remote control of DVD/VCR. "L1" will appear on the front

display. Select the desired TV-program at Satellite Receiver.

Connection to a Decoder (for Premiere Programs)

SCART-cable (not supplied)

DVD/VCR

SCART-cable (not supplied)

Note: Make sure that AV - mode in SYSTEM SETUP - menu has been set

to DEC .

If you set to [AV], the output signal from the decoder will be seen on the TV

while the DVD/VCR is turned off.

Setting the TV to the AV-Channel

We recommend that television and DVD/VCR are being connected with a scart cable.

In this case, the setting of AV-channel is not necessary. Picture and sound of video cassette will be transmitted to

television through the scart cable automatically. Please read the next page.

In case of no scart cable connection,

you must set the television to the AV-

channel. Pay attention to the following

notice:

A built-in TV-broadcast in DVD/VCR can

do the video playback through the sup-

plied antenna cable. This broadcast is

sent on UHF, channel 60. To receive this

broadcast, you must tune your televi-

sion to channel 60 in UHF-band.(see

step 2)

In case a broadcast has already sent

to channel 60 in your area or you con-

nect a additional equipment (e.g. Sat-

ellite receiver) with a coaxial cable

(without a scart cable), you must tune

the sending channel in DVD/VCR (see

step 3). In your television store the both

equipment (the DVD/VCR and the sat-

ellite receiver) to 2 different program

positions.

Example: Your satellite receiver is sent

to channel 60. You tune the DVD/VCR

to channel 64 (see step 3).

(If your DVD/VCR is also sent to chan-

nel 60, the interference will occur.)

In your television store the channel 60

to e.g. program position 3 and store the

channel 64 to e.g. program position 4.

Note that the program position 4 must

be suitable for video-playback espe-

cially. Please see the owner's manual

for your television. If the playback pic-

ture is often distored, you must select

the other program position for DVD/

VCR.

TEST

Note:

If you receive one TV-program on channel 59, 60 or 61, the interference can be occurred to the built-in TV channel

in DVD/VCR. If you use a scart cable for the transmission of picture and sound, you can cut off the built-in TV-

program. Then the video playback through the supplied antenna cable is not possible any more. Press CHANNEL

repeatedly (at step 1) until OFF will appear.(OFF appears after 69 or before 23)

DVD/VCR

TV-unit

Cable TV-

Decoder

connection

RF-Output

SYSTEM SETUP

CLOCK SET

LANGUAGE/üáúIK

AV2

[DEC]

RF OUT

[K]

SELECT :

ENTER : ENTER

EXIT

Preparation

• Turn on the TV.

• Make sure the power of DVD/VCR has been turned off.

Press ON/STANDBY on the DVD/VCR and keep pressing

it until the display shows rF:. The number next to rF: is the

channel in UHF-band to which you must tune your TV-set.

VCR

Switch your television to the program position on which the

video playback is seen. Start the channel search of your

television until "TEST" appears. Store this tuning in televi-

sion like also the case of the reception for normal televi-

sion-channels you would store.

If you want to use your DVD/VCR,

switch your television to this program

position.

If there is interference in the picture (you see 2 programs

simultaneously or what is called Ghosts), change the send-

ing channel in DVD/VCR. To do this, go back to the step 1.

Use CHANNEL button on the DVD/VCR to change the

number next to the rF:. Then return to step 2 and tune the

television newly.

Press ON/STANDBY on the DVD/VCR to turn off the

DVD/VCR.

1,4

Component video outputs/inputs

PROGRESSIVE outputs/inputs

Some TVs or monitors are equipped with component video inputs that are capable of reproducing a progressively scanned

video signal. Connecting to these inputs allows you to view the highest quality pictures with less flicker.

INTERLACED outputs/inputs

Some TVs or monitors are equipped with component video inputs. Connecting to these inputs allows you to enjoy the highest

quality DVD picture playback.

Connecting to an audio system and TV equipped with component video inputs

DVD/VCR

Audio (L) Output

• Make the following setting

On-screen

display

Interlaced inputs

Progressive inputs

Notes:

• Actual labels for component video inputs may vary depending on the TV manufacturer. (ex. Y, R-Y, B-Y or Y, CB, CR)

• In some TVs or monitors, the colour levels of the playback picture may be reduced slightly or the tint may change. In such a

case, adjust the TV or monitor for optimum performance.

Note:

In connecting to a TV that are not capable of reproducing a progressively scanned video signal using the component

sockets, do not select "Progressive" in "Output" menu. If you do it, the component video outputs does not feed the

correct signals and you can not see any picture (see page 58).

Connect to an AV Amplifier with built-in digital surround

If you are using an Amplifier with a built-in digital surround as follows, you can enjoy the various audio systems such as Dolby

Digital and DTS by using the Coaxial Digital Output.

Use this connection to connect an:

• AV amplifier with built-in *Dolby Digital decoder

• AV amplifier with built-in *DTS decoder

SCART-Socket

(for TV-RGB/Composite)

Notes:

• The COAXIAL jack is useful only for DVD section.

• DTS audio will be output only from the COAXIAL output. To hear DTS audio, DTS-Decoder is necessary.

When playing DTS-encoded CDs, only noise will be heard from the speakers or analogue stereo outputs.

• Some DTS decoders which do not support DVD-DTS interface may not work properly with the unit.

Turn on your TV and select the AV-

Program position, on which you have

already set your DVD/VCR. (it will hap-

pen automatically by Scart-cable con-

nection). So you can follow up the all

setting on TV screen.

TEST

Notes:

• If the unit does not operate properly,

or No key operation (by the unit and/

or the remote control): Static elec-

tricity, etc., may affect the player's

operation. Disconnect the AC power

cord once, then connect it again.

• If no buttons are pressed for more than

60 seconds, the MENU screen will re-

turn to normal TV-operation automati-

cally.

Component video cable (not supplied)

Component (Y) Output

Component (P

) Output

Component (P

) Output

Stereo Amplifier

To Audio (L) Input

Audio (R) Output

To Audio (R) Input

AUDIO Cord (supplied)

See Output selection (P.58).

Component

Progressive

Coaxial digital cable (not supplied)

DVD/VCR

Coaxial digital Audio Output

SCART-cable (not supplied)

Setting the On-screen language

Preparation:

• Press the

button to turn on the DVD/VCR.

• Press VCR to select the VCR mode. (The VCR indicator will light.)

You can choose from two different languages (English or Rus-

sian) for the on-screen displays.

Press VCR MENU. Press

to select the "ìCTAHOBKA

CàCTEMõ" menu, then press

ENTER.

If you use the unit for the first

time and press VCR MENU, in-

stead of the main menu screen

on the right the "LANGUAGE"

set up menu screen in step 3

may appear.

Press

"LANGUAGE" option, then press

ENTER.

Press

desired language: English or

Russian (êìëëäàâ), then

press ENTER.

Press VCR MENU repeatedly until the TV picture appears on

the screen.

Playback connection

Component

video input

If the TV has the Component

input, connect the DVD video

player with the Component

lead. When using the

Component lead, do not

connect the yellow video lead.

AV Amplifier with

built-in various

decoder as above

To SCART

input

áÄèàëú èé íÄâåÖêì

ÄÇíé èéÇíéê

Çõäã

ìCTAHOBKA BM

ìCTAHOBKA KAHAãA

ìCTAHOBKA CàCTEMõ

BõÅêATú

BBOÑ

: ENTER

BõïOÑ : MENU

to select the

ìCTAHOBKA CàCTEMõ

HACTPOâKA óACOB

LANGUAGE/üáúIK

AV2

[AV]

RF OUT

[K]

BõÅêATú

BBOÑ

: ENTER

BõïOÑ

: MENU

to select the

LANGUAGE/ü3úIK

ENGLISH

PìCCKàâ

SELECT :

OK: ENTER

Table of Contents

Chapters

Table of Contents

Playback Connection; Setting The Tv To The Av-Channel; Setting The On-Screen Language - Toshiba SD-25VLSR Service Manual