Commercial Snowblower WARRANTY REGISTRATION AND POLICY Buhler Manufacturing products are warranted for a period of twelve (12) months from original date of purchase, by original purchaser, to be free from defects in material and workmanship under correct, normal agricultural use and proper applications.
Commercial Snowblower Always review operator’s manual before starting new machine. Do not let inexperienced operators or children run this equipment. Never service or clean unit while it is running. Do not remove shields. Stay clear of augers. Stay clear of discharge chute. Rocks can be picked up and thrown.
Page 4
Commercial Snowblower SNOWBLOWERS This manual is for both Commercial Hydraulic Snowblowers and Commercial PTO Drive Snowblowers. The hydraulic models come in 60”, 74” and 84” widths. The PTO drive model is only available in an 84” width. Hydraulic models come with four different motor series.
Commercial Snowblower 1. HYDRAULIC DRIVE: All snowblower hydraulic blocks are set at the factory for a 2800 - 3000 psi system. Refer to the section on the hydraulic control block if your system does not fall into this range. 2. ALL: Depth of the cut can be partially controlled by tilting the snowblower forward or backward.
Page 8
Commercial Snowblower OPERATING INSTRUCTIONS – cont’d. 10. ALL: Chain tension on auger chain should be set at 3/8” to 1/2” slack. 11. LUBRICATION: a) ALL: The gear teeth on the chute control should be periodically lubricated with gun grease. b) PTO DRIVE: PTO shaft universal joints and square shaft slide should be periodically lubricated with a grease gun.
Commercial Snowblower HYDRAULIC CONTROL BLOCK NON-STALLING-FAN FEATURE: The Hydraulic Snowblower has a unique modulating element that keeps the blower fan from stalling in an overloaded condition. This is accomplished by starving the hydraulic flow to the front auger motor (which then stops feeding the fan) and diverts all of the flow (and energy) to the main fan motor.
Commercial Snowblower 10bc 10ef 14bc DESCRIPTION Main Block Logic Element Element Seal Kit Control Valve Seal Kit No-Load Valve Seal Kit Chute Cont. Valves Seal Kit No-Load Press. Coil Chute Up Down Coil Chute Left Right Coil Harness Assembly Check Valve...
Commercial Snowblower SPOUT ASSEMBLY FOR ALL SNOWBLOWERS: Remove two of the grooved spout rollers to mount the discharge spout. Replace the two rollers to hold spout in place. Install the 2 ½” x 8” cylinder on the spout using the pins supplied.
Page 12
Commercial Snowblower ASSEMBLY INSTRUCTIONS – cont’d. Using tape or a bright colored marking pen, mark on the outer shields the position where the shaft is completely pushed together and the position where you have a 4” overlap. Watch these marks when moving the blower through all possible operating angles to see that the PTO shaft stays within this range.
Page 13
Commercial Snowblower ASSEMBLY INSTRUCTIONS – cont’d. 4. PTO SHIELD: All PTO snowblowers are supplied with a PTO shield (#18). To install, remove the two rear bolts at the top of the gearbox (#34). Bolt the PTO shield to the gearbox by the hinges using these same bolts.
Commercial Snowblower WHEN ORDERING PARTS Always give your dealer the Model and Serial Number of your machine to assist him in ordering and obtaining the correct parts. Use the exploded view and tabular listing of the area of interest to exactly identify the required part.
Commercial Snowblower 906348 Motor Washer 13/32'' hole x 2'' OD 906574 Bronze Bushing 7/8'' OD x 1'' HYDRAULIC COMMERCIAL SERIES SNOWBLOWER – 24” HOUSING...
Commercial Snowblower 2 ½” x 8” CYLINDER ASSEMBLY Item # Part # Description 24982 Tube Weldment 108655 Shaft 1.25 dia x 15.54 Lg 23156 2.50 Dia Headplate 13109 2.50 Dia Piston 13090 Piston Rod Clevis (Cast) 82330 2.50 OD x e Sect O-Ring 83330 2.50 OD x o Sect Backup Washer...