Advertisement
SERVICE STG
PARAMETER
Configure System
Learning System >
Driving Cycle
Parameter
Time delay open
Maintenance
Drive
Functions
Entrance System
Operation mode
Control Panel
Locking
SERVICE STG
PARAMETER
Configure System
Learning System >
Entrance System
Parameter
Control Panel
Maintenance
Locking
Functions
CAN-BUS
Operation mode
Input/Output
Miscellaneous
SERVICE STG
PARAMETER
Configure System
Learning System >
Entrance System
Parameter
Control Panel
Maintenance
Locking
Functions
CAN-BUS
Operation mode
Input/Output
Miscellaneous
SERVICE STG
SERVICE STG
PARAMETER
PARAMETER
Configure System
Configure System
Learning System >
Learning System >
Entrance System
Entrance System
Parameter
Parameter
Control Panel
Control Panel
Maintenance
Maintenance
Locking
Locking
Functions
Functions
CAN-BUS
CAN-BUS
Operation mode
Operation mode
Input/Output
Input/Output
Miscellaneous
Miscellaneous
SERVICE STG
PARAMETER
Configure System
Learning System >
Entrance System
Parameter
Control Panel
Maintenance
Locking
Functions
CAN-BUS
Operation mode
Input/Output
Miscellaneous
Responds to AUX00_IN, AUX01_IN or AUX04_IN set to "2SoK_NSK and the control wired appropriately.
LOCKING
>
>
>
Locking functions
>
>
Lock type
>
>
Start Delay
>
>
Closed VRR Error
>
Closing Force
>
>
>
>
>
>
>
>
>
>
INPUT/OUTPUT
>
STG
>
>
STG
>
>
FEM0
AUX0_IN
>
>
FEM1
>
AUX1_IN
>
Ext. Sw IN
AUX4_IN
>
Emerg. Open/Close
AUX0_OUT
EMERG, STOP Reset
ZLP
INPUT/OUTPUT
>
>
>
>
STG
>
>
>
>
>
>
FEM0
>
>
>
>
FEM1
>
>
Ext. Sw IN
>
>
Emerg. Open/Close
>
>
EMERG, STOP Reset
INPUT/OUTPUT
>
EMERG. OPEN/CLOSE
>
>
STG
>
>
FEM0
Function
>
>
FEM1
Speed (Flip Flow only)
>
>
Ext. Sw IN
Emerg. Open/Close
>
EMERG, STOP Reset
Closed VRR Error
Closing Force
Closed VRR Error
Closed VRR Error
2
0 Disabled
0 Disabled
0 Disabled
1 Enabled
1 Enabled
1 Enabled
0
0
0
CAN-BUS
FEM0
FEM1
FEM2
AKI1
S I1
AKI1
>
>
0
>
0
0
0
0
0
0
>
Ext. Sw IN
0 Ext. Sw IN
>
1 Inactive by 1 Way
>
and locked
>
0
5 Disabled
0
0
Enable to comply with ANSI/BHMA A156.10for Exterior
sensor to be active in Exit mode and the door is open.
>
>
0
>
0
0
0
0
Briefly increases
closing force to
relieve locking bolt.
0=low force
40=high force
0
During Start Delay,
door is powered in
closing direction to
relieve any binding
on electric lock.
Any Can-Bus module or
sensor connected is
0
automatically identified &
0
displayed with a "1".
0
Disconnected units are
0
displayed with "?" and must
0
be removed manually with
0
FPC902. Not available units
are displayed with a "0".
Configurable Input Terminals 4,6,and
18 on STG Control. Note: With
parameters identified as "Safety", a
closed contact is required for normal
door operation.
AUX0_OUT: Dry contacts on STG to
Terminals 8(NO), 9(COM), 10(NC)
Rated @ 1 Amp 30VDC.
ZLP1: Additional Circuit Board to
connect threshold Safety Beams.
Set ELS to be active. See S5100
Parameter Settings record sheet.
FUNCTION
0 Disabled
1 Emergency Open
2 Emerg. Close
Manual&RemSw
3 Emerg. Close
Locked
FEM0,FEM1
contain settings
for input/outputs
for Expansion
Modules.
Ext. Sw IN;
Five
options
listed.
Advertisement
