Page 1
THANK YOU We appreciate the trust and confidence you have placed in Hampton Bay through the purchase of this patio heater. We strive to continually create quality products designed to enhance your home. Visit us online to see our full line of products available for your home improvement...
Safety Information (continued) WARNING: ONLY use this appliance on a flat LEVEL non WARNING: In the event of an uncontrollable fire, flammable surface or ground. immediately disconnect the gas cylinder moving it away from fire and contact the fire services. DO NOT PUT YOURSELF AT RISK! WARNING: When positioning, ensure the unit is a minimum of 40 inches (1m) from flammable items or...
Warranty 2 YEAR LIMITED WARRANTY WHAT IS COVERED We warrant to the original consumer purchaser that all aspects of this product will be free of defects in material and workmanship for 2 years from the date of purchase. A replacement for any defective part will be supplied free of charge for installation by the consumer. This warranty shall be effective from the date of purchase as shown in the purchaser’s receipt.
PLANNING ASSEMBLY Before You Start, check the contents of the box and make sure you have all the parts and fittings listed. If not, contact Hampton Bay Customer Service at 1-855-HD-HAMPTON. When you are ready to start, make sure that you have the right tools at hand, plenty of space and a clean dry area for assembly.
Pre-Assembly (continued) PACKAGE CONTENTS Part Description Quantity Part Description Quantity Table Top Base Upper Support Pole Upper & Lower Cylinder Chamber Supports (A, B, C) Lantern And Hose Base Plate Upper Cylinder Chamber Wall Regulator Lower Cylinder Chamber Wall Reflector Handle Lower Support Pole Top Panel Side Panels...
Assembly Assembling the legs Attaching the cylinder chamber walls □ Attach the base plate (C) to the base (A) using the two □ Using 11 of the bolts (AA) and nuts (BB), attach the lower prefitted bolts. cylinder chamber wall (E) to the bottom of the cylinder chamber supports (B) and attach the upper cylinder □...
Page 9
Assembly (continued) Attaching the lower support pole Attaching the cylinder chamber door □ Attach the lower support pole (F) to the cylinder chamber □ Attach the upper cylinder chamber door panel (G) to the supports (B) using six bolts (CC) and nuts (BB). lower cylinder chamber door panel (H) using three bolts (AA) and nuts (BB).
Page 10
Assembly (continued) Attaching the upper support pole and Attaching the lantern table top □ Feed the hose down through the support pole (J) and secure the lantern (K) to the support pole (J) using four □ Slide the table top (I) down over the lower support bolts (CC), washers (DD) and spring washers (GG).
Page 11
Assembly (continued) Attaching the regulator and propane Fitting the reflector handle bottle □ Using the pre-fitted R-clip (1) and pin (2), secure the NOTE: THE CYLINDER MUST BE POSITIONED AS SHOWN IN reflector handle (M) to the bracket as shown. THE PATIO HEATER CYLINDER CHAMBER TO PROVIDE VAPOR WITHDRAWAL.
Page 12
Assembly (continued) Assembling the reflector Attaching the reflector to the lantern WARNING: While every precaution has been made in the manufacture of this product, care must be taken during assembly in case sharp edges are present. □ Fit the reflector to the lantern (K) using three bolts (FF) and washers (EE).
Operation □ The heater, when installed, must be electrically grounded in accordance with local codes or, in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.1. □ Certain materials or items, when stored under the heater, will be subjected to radiant heat and could be seriously damaged. □...
Operation (continued) □ Important - Make sure the gas bottle is placed level within the base. □ Should you need to change the gas bottle, confirm the gas supply is turned off at the regulator or bottle / cylinder valve, and there are no sources of ignition (cigarettes, open flame, sparks, etc.) near before proceeding.
Operation (continued) LEAK TESTING Your patio heater has been checked at all factory connections for leakage. To check the connection at the gas hose/regulator/cylinder: □ Ensure you are in a well ventilated area. □ Confirm all control knobs are in the off position. □...
□ It is a necessity to contact an authorized source for replacement of parts and/or servicing. □ This work must be carried out by a qualified gas technician. □ Spare parts may be obtained by contacting Hampton Bay Customer Service at 1-855-HD-HAMPTON. Care & Cleaning □...
Page 18
Questions, problems, missing parts? Before returning to the store, call Hampton Bay Customer Service 8 a.m.-7 p.m., EST, Monday-Friday, 9 a.m. - 6 p.m., EST, Saturday 1-855-HD-HAMPTON HAMPTONBAY.COM Retain this manual for future use.
Need help?
Do you have a question about the HDMIRAGECO PC and is the answer not in the manual?
Questions and answers