Table of Contents
Advertisement
Quick Links
Instructions - Parts
Graco InSite
Remote Reporting Field Installation Kit
For remote reporting of actual temperature, temperature setpoint, actual pressure,
pressure setpoint, cycles, and GPS location from a Reactor
Not approved for use in explosive atmospheres or hazardous locations.
Model 24T278
Important Safety Instructions
Read all warnings and instructions in this manual
and in your Reactor manual. Save all instructions.
™
332590A
®
proportioner.
EN
ti22093a
Advertisement
Table of Contents
Related Manuals for Graco InSite 24T278
Summary of Contents for Graco InSite 24T278
- Page 1 Instructions - Parts ™ Graco InSite 332590A Remote Reporting Field Installation Kit For remote reporting of actual temperature, temperature setpoint, actual pressure, ® pressure setpoint, cycles, and GPS location from a Reactor proportioner. Not approved for use in explosive atmospheres or hazardous locations.
-
Page 2: Table Of Contents
......13 255407 Graco Standard Warranty ....14 255408... -
Page 3: Warnings
NOTE: The plate is on the right side of the Electric NOTICE Reactor and on the left side of the Hydraulic Reactor. To prevent damage to the Graco InSite, do not expose to rain. To prevent electric shock, wait 5 minutes after turning... - Page 4 Installation NOTE: The difference between style 1 and style 2 DIN rails is the layout of the terminal blocks on the left hand side. To prevent electric shock, do not pinch wires when NOTE: In the following steps, ensure stripped wire ends installing control box in the following step.
- Page 5 Installation B, C . 1: Electric Reactor DIN Rail Style 1 B, C . 2: Electric Reactor DIN Rail Style 2 B, C . 3: Hydraulic Reactor DIN Rail Style 3 332590A...
- Page 6 Installation 12. On the left wall inside the Reactor cabinet, locate 15. Connect PUMP cable (P) to J12 on motor control and identify whether your system uses the tempera- board. ture control module or temperature control board. Models E-30 and E-XP2 See F .
- Page 7 Installation Install Cellular Module 19. Loosen left side acorn nuts (AN) holding Reactor display to frame until display can be lifted enough to NOTICE slide bracket between frame and display. See F . 7. To prevent cracking the plastic shell of the cellular NOTE: It is not necessary to completely remove the module (1), do not overtighten nuts (5) when install- acorn nuts on the electric Reactor.
- Page 8 Installation Update Software, If Needed e. Remove the software update token (9) from the Temperature Control Module. NOTE: If the Reactor has a temperature control module and was built before 2010, a software update is needed. Otherwise, installation is complete. 28.
-
Page 9: Operation
Operation Registering and Activating the Graco InSite To register and activate the Graco InSite, go to www.GracoInSite.com, click on “InSite Login”, then fol- low the instructions on the screen. Find and record the 15 digit serial number from the cel-... -
Page 10: Troubleshooting
Move system to a location with cel- tion. lular service to establish cellular connection. Cannot view data for my unit(s) on Graco InSite unit has not been acti- Activate unit. See Registering and website. vated. Activating the Graco InSite on page 9. - Page 11 Troubleshooting Problem Cause Solution Temperature data not displayed on 4-pin connector is not plugged into Ensure unit is properly installed. website. the correct terminal on the tempera- See Installation on page 3. ture control board or module. Reactor temperature measurement See Reactor repair manual.
-
Page 12: Parts
Parts Parts Part Description 24R926 MODULE, cellular and GPS 262922 CONTROL BOX . 2a ENCLOSURE, power supply . 2b BRACKET . 2c 127191 HARNESS, wire (not shown) . 2d NUTS, keps, hex head, 10-24, with lock washers . 2e SPACER, nylon . -
Page 13: Technical Data
Technical Data Technical Data Graco InSite Remote Reporting Field Installation Kit Metric Control Box Weight 2.3 lb 1.0 kg Cellular Module Weight 0.5 lb 0.2 kg Voltage into Control Box 100-240VAC, 50-60 Hz Operating Temperature -22 to 167°F -30 to 75°C Storage Temperature -40 to 185°F... -
Page 14: Graco Standard Warranty
With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective.