Related Manuals for Z GRILLS ZPG-7002E
Summary of Contents for Z GRILLS ZPG-7002E
- Page 1 Smoke Shut Down High Cycle Power www.zgrills.com WOOD PELLET GRILL ZPG - 7002E OWNER’S MANUAL 1-785-317-5170 EMAIL:support@zgrills.com WEBSITE:www.zgrills.com...
-
Page 2: Table Of Contents
CONTENTS WARNINGS COMPOENT LIST ASSEMBLY INSTRUCTIONS INITIAL FIRING INSTRUCTIONS SUBSEQUENT START-UP OPERATING TIPS MAINTENANCE & CLEANING TROUBLESHOOTING DIGTAL THERMOSTAT CONTROL WIRING DIAGRAM Z GRILLS SUPPORT -Y LIMITED WARRANTY... -
Page 3: Warnings
Do not try to smother the fire. Clean and maintain your grill after each time use. We suggest that use Z GRILLS BBQ WOOD PELLETS, which are specifically made to work in our grills. Do not use your grill on rainy days. -
Page 4: Compoent List
ASSEMBLY INSTRUCTIONS COMPONENT LIST Description Description ITEM ITEM Ⅰ Φ Φ (1/4-20*12mm) Φ Φ Hexagon Nut (1/4-20) Gasket（ Φ . *Φ 12 10 * . mm ） Bolt (5/32-32*5mm) (Φ13*Φ25*2mm) (Φ6.5*Φ15*1mm) Bolt (5/32-32*6 Hexagon Kep Nut (5/32-32) Spring Washer (Φ6.5*Φ10*1.2mm) Ⅱ... - Page 5 1.MOUNTING THE BODY FRAME TO THE CHAMBER: Lid Assembly: 1.)With the help of another person, put the Chamber on carboard, then attach 2 Left 1.)Using a screwdriver to remove the screws and gaskets that have been Legs(38) to Chamber(1) with1/4-20*12mm Bolt(46), Φ6.5*Φ10*1.2mm Spring Washer assembled in the Chamber.
- Page 6 2.Assembling of Hopper 4. Attaching Hopper Handle to Hopper Lid: Insert Hopper Assembly II(61) into Hopper Assembly I(3), align the holes as shown in Using 5/32-32*5mm S/S Bolt(54) through Φ . Φ 12 10 * . mm Gasket(53), and install FIG 5.
- Page 7 6. Attaching the Smokestack and Chimney Cap: 8.Attaching The Grease Drain Pan: Using 1/4-20×12mm Bolt(48) through the holes of Smokestack(15) and the hole of Attaching the Grease Drain Pan (6) over the Heat Baffle (5) as per direction of below Smoke Stack Gasket(16), Align the hole of Grill body, attaching Φ...
-
Page 8: Initial Firing Instructions
Please read this manual carefully and follow it step by step before starting your Z Grills for the first time and each time the grill runs out of pellets. 1.Remove the Porcelain Grills, Grease Drain Pan and Heat Baffle from the interior of the grill. -
Page 9: Subsequent Start-Up
5.If this step is not successful, see TROUBLESHOOTING or contact Z GRILLS Technical Support to help diagnose the problem before proceeding LEr(Low Temperature Alarm ) to the MANUAL LIGHTING INSTRCUTIONS below: Grill temp was below 150℉... -
Page 10: Operating Tips
Use Z Grills Cover to protect your grill is highly recommended. Use a high-quality car wax on the outside surfaces of the grill can protect your paint finish. -
Page 11: Troubleshooting
TROUBLESHOOTING cleaning brush to give the Porcelain-coated Grill Grates a quick brushing when you finish the barbecue. It takes only a minute and it will be ready the next time CAUTION: Make rill ompletely nplugged efore you want to use the grill. inspection, cleaning, maintenance or service work. -
Page 12: Digtal Thermostat Control Wiring Diagram
Please state your authorized dealer, Customer Service to place an order your name, phone number, address, Get your new parts Z Grills model number, serial number and part identification number from Contact with your the COMPONENT LIST. Z Grills dealer... -
Page 13: Z Grills Support
Purchaser's name, phone number, address, Z Grills model number, serial number and part identification number from the COMPONENT LIST Z Grills Inc guarantees a 3 years warranty of our products from the date of purchase Please describe your problem accurately so that we can help you figure out.