Table of Contents
Advertisement
With the remote control unit it's possible to perform operation
of...
• The primary monitor
• Monitors with a specified ID No.
• All primary/secondary monitors
It's necessary to specify which type of operation will be
performed in advance.
1. If using the remote control unit, press the MODE button
for approx 5 seconds.
If using the monitor buttons, hold both the MENU
button and
button at the same time on the primary.
REMOTE CONTROL MODE
MODE
EXPAND ITEM
ID No.
ID No. DISPLAY
Operate this monitor.
OK
2. Press the
or
button, select the mode, then perform
settings.
THIS MONITOR ONLY
Performs operation of only the primary using the remote
control unit.
[Example] If the volume is lowered, the volume of the primary
will lower.
Secondary
ID No.: 2
Secondary
ID No.: 3
Lower the volume.
SPECIFIED MONITOR
Performs operation of a monitor with a specified ID No. using
the remote control unit.
Press the
or
button to select ID No., then press the
or
button to select the ID No. of the monitor that you will
operate.
* When it receives signals from the remote control unit,
"Operating specified monitor." will be displayed on the
primary screen.
[Example] If ID No. is set to 3 and the volume is lowered, the
volume of the monitor for ID No.: 3 will lower.
Secondary
ID No.: 2
Secondary
ID No.: 3
VOLUME 10
Lower the volume.
When you would like to confirm the ID No. that is set to the
monitor, press the
or
button to select ID No. DISPLAY, then
press the ENTER button. The ID No. will be displayed on the
screen.
Remote Control Mode
THIS MONITOR ONLY
CANCEL
END:[RETURN]
Primary
ID No.: 1
VOLUME 10
Secondary
ID No.: 4
Primary
ID No.: 1
Secondary
ID No.: 4
ALL MONITORS
Performs operation of all primary/secondary monitors.
*
will be displayed on the menu of the primary.
ALL [EXPAND ITEM:OFF]
* When it receives signals from the remote control unit,
"Operating all monitors." will be displayed on the secondary
screen. (Excluding power and input mode selection operation)
* Settings may not be reflected depending on the state of the
connected monitors.
[Example] If the power for the primary is turned ON, the power
for all the monitors will be turned ON.
Secondary
ID No.: 2
Power ON
Secondary
ID No.: 3
Power ON
Turn the power ON.
Press the
or
button to select EXPAND ITEM, and press
the
or
button to select to perform this action or not.
OFF ...........For all monitors, only power, input mode
selection, and product information display
operations will be recognized.
ON .............For all monitors, all operations will be
recognized.
After returning to the normal screen with
procedure 3, when 5 minutes have passed from
the end of operation, it will automatically return
to OFF.
*
ALL [EXPAND ITEM:ON]
of the primary.
* Even when REMOTE CONTROL MODE is set
to ALL MONITORS, certain settings such as
LAN settings and ID No. settings will not be
reflected on the other monitors.
3. Press the
or
button to select OK, then press the
ENTER button and return to the normal screen.
4. Perform operation.
Caution
• When the remote control mode is set to ALL MONITORS
and EXPAND ITEM is set to ON, performing remote control
operations that change adjustment values will result in
the secondary adjustment values being the same as the
primary adjustment values.
Secondary
Primary
ID No.: 2
ID No.: 1
VOLUME 12
VOLUME 11
Secondary
Secondary
ID No.: 3
ID No.: 4
VOLUME 9
VOLUME 10
Lower the volume.
Be careful of this when adjusting individual displays.
TIPS
• You can copy the setting values of the primary to other
monitors with COPY SETTING VALUE. (See page 29.)
• The buttons on the monitor itself (primary) are also effective
in remote control mode.
Primary
ID No.: 1
Power ON
Secondary
ID No.: 4
Power ON
will be displayed on the menu
Secondary
Primary
ID No.: 2
ID No.: 1
VOLUME 10
VOLUME 10
Secondary
Secondary
ID No.: 3
ID No.: 4
VOLUME 10
VOLUME 10
23
E
Advertisement
Table of Contents
