Table of Contents
Advertisement
With the remote control unit it's possible to perform operation
of...
• The primary monitor
• Monitors with a specified ID No.
• All primary/secondary monitors
It's necessary to specify which type of operation will be
performed in advance.
1. If using the remote control unit, press
seconds.
If using the monitor buttons, hold both
the same time on the primary.
REMOTE CONTROL MODE
MODE
Operate this monitor.
OK
2. Press
or
, select the mode, then perform
settings.
THIS MONITOR ONLY
Performs operation of only the primary using the remote
control unit.
[Example] If the volume is lowered, the volume of the primary
will lower.
Secondary
ID No.: 2
Secondary
ID No.: 3
Press
SPECIFIED MONITOR
Performs operation of a monitor with a specified ID No. using
the remote control unit.
Press
or
to select ID No., then press
select the ID No. of the monitor that you will operate.
* When it receives signals from the remote control unit,
"Operating specified monitor." will be displayed on the
primary screen.
[Example] If ID No. is set to 3 and the volume is lowered, the
volume of the monitor for ID No.: 3 will lower.
Secondary
ID No.: 2
Secondary
ID No.: 3
VOLUME 10
Press
When you would like to confirm the ID No. that is set to the
monitor, press
or
press
. The ID No. will be displayed on the screen.
24
E
Remote Control Mode
MODE
for approx 5
and
THIS MONITOR ONLY
CANCEL
END···[RETURN]
Primary
ID No.: 1
VOLUME 10
Secondary
ID No.: 4
to lower the volume
Primary
ID No.: 1
Secondary
ID No.: 4
to lower the volume
to select ID No. DISPLAY, then
ALL MONITORS
Performs operation of all primary/secondary monitors.
ALL
*
will be displayed on the menu of the primary.
* When it receives signals from the remote control unit,
"Operating all monitors." will be displayed on the secondary
screen. (Excluding power and input mode selection operation)
* Settings may not be reflected depending on the state of the
connected monitors.
[Example] If the power for the primary is turned ON, the power
for all the monitors will be turned ON.
at
Press
or
to select to perform this action or not.
OFF ...........For all monitors, only power, input mode
ON .............For all monitors, all operations will be
3. Press
return to the normal screen.
4. Perform operation.
Caution
• When the remote control mode is set to ALL MONITORS
and EXPAND ITEM is set to ON, performing remote control
or
to
operations that change adjustment values will result in
the secondary adjustment values being the same as the
primary adjustment values.
Secondary
ID No.: 2
VOLUME 12
Secondary
ID No.: 3
VOLUME 9
Press
to lower the volume
Be careful of this when adjusting individual displays.
TIPS
• You can copy the setting values of the primary to other
monitors with COPY SETTING VALUE. (See page 30.)
• The buttons on the monitor itself (primary) are also effective
in remote control mode.
• When monitors connected in a daisy chain are in standby
mode/input signal waiting mode for LOW POWER,
operation cannot be performed for subsequent monitors.
Secondary
Primary
ID No.: 2
ID No.: 1
Power ON
Power ON
Secondary
Secondary
ID No.: 3
ID No.: 4
Power ON
Power ON
POWER
Press
to turn the power ON
to select EXPAND ITEM, and press
selection, and product information display
operations will be recognized.
recognized.
After returning to the normal screen with
procedure 3, when 5 minutes have passed from
the end of operation, it will automatically return
to OFF.
ALL [EXPAND ITEM]
will be displayed on the menu of
the primary.
* Even when REMOTE CONTROL MODE is set
to ALL MONITORS, certain settings such as
LAN settings and ID No. settings will not be
reflected on the other monitors.
or
to select OK, then press
Primary
Secondary
ID No.: 1
ID No.: 2
VOLUME 11
VOLUME 10
Secondary
Secondary
ID No.: 4
ID No.: 3
VOLUME 10
VOLUME 10
or
ENTER
and
Primary
ID No.: 1
VOLUME 10
Secondary
ID No.: 4
VOLUME 10
Advertisement
Table of Contents
