Hand Home Position Adjustment; To Adjust Home Positions; Using The Digital Compass; To Perform A Digital Compass Operation - Casio 5476 Operation Manual

Hide thumbs Also See for 5476:
Table of Contents

Advertisement

2. Press D to move the fl ashing in the sequence shown below to select the other settings.
City Code
DST
12/24-Hour Format
(page E-13)
(page E-14)
Illumination Duration
Button Operation Tone On/Off
(page E-46)
(page E-50)
3. When the timekeeping setting you want to change is fl ashing, use E and/or B to change it as
described below.
Screen
Change the city code
Toggle between daylight saving time (ON) and
standard time (OFF).
Toggle between 12-hour (12H) and 24-hour (24H)
timekeeping.
Reset the seconds to 00
(If the current seconds count is between 30 and 59,
one is added to the minute count).
Change the hour or minutes
Change the year, month, or day
E-16

Hand Home Position Adjustment

Strong magnetism or impact can cause the hands of the watch to go out of alignment.
Home position adjustment is not necessary when the analog time and digital time are the same time in
the Timekeeping Mode.

To adjust home positions

1. In the Timekeeping Mode, hold down A and keep it depressed for
about fi ve seconds until H.SET appears on the lower display.
When you release A after H.SET appears, the second hand will
move to 12 o'clock. This indicates the second hand home position
adjustment mode.
Though ADJ will appear in the lower display about two seconds
after you hold down A, do not release the button yet. Keep it
depressed until H.SET appears.
Use the D button to select a hand for adjustment. Each press of
D cycles in sequences from the second hand, to the hour and minute
hands, and then the mode dial hand. Selecting a hand causes it to
move to 12 o'clock and the content of the upper display changes
as shown in the table below.
Upper display
Selected hand
Flashing 00
Second hand
Flashing 0:00
Hour and minute hands
Flashing Sub
Mode dial hand
If the selected hand does not move exactly to 12 o'clock, perform step 2 below to adjust it.
E-18

Using the Digital Compass

You can use the Digital Compass Mode to determine the direction of north, and to check your bearing to a
destination.
For information about what you can do to improve digital compass reading accuracy, see "Calibrating
the Bearing Sensor" (page E-23) and "Digital Compass Precautions" (page E-30).

To perform a digital compass operation

1. Place the watch on a fl at surface. If you are wearing the watch, make sure that your wrist is horizontal
(in relation to the horizon).
2. Point the 12 o'clock position of the watch in the direction you want to check.
3. In any mode (except a setting mode), press C to perform a digital compass operation.
This will cause the mode dial hand to move to COMP.
COMP will appear in the lower display to indicate that a digital compass operation is in progress.
After about two seconds, the second hand will point in the direction of magnetic north, and the
display will show the direction or the bearing angle that 12 o'clock is pointed.
E-20
Digital Compass Readings
When you press C to start a digital compass operation, COMP will initially appear on the lower
display. About two seconds after you start a digital compass operation, an indicator will appear in the
lower display to indicate what direction the 12 o'clock position of the watch is pointed. The second
hand will point to magnetic north.
After the fi rst reading is obtained, the watch will continue to take digital compass readings automatically
each second for up to 20 seconds. After that, the digital compass operation will stop automatically.
The direction indicator and angle value will show - - - to indicate that the digital compass operation is
complete.
Auto light is disabled during the 20 seconds that digital compass readings are being taken.
The following table shows the meanings of each of the direction abbreviations that appear on the lower
display.
Direction
Meaning
Direction
Meaning
North-
N
North
NNE
northeast
East-
E
East
ESE
southeast
South-
S
South
SSW
southwest
West-
W
West
WNW
northwest
The margin of error for the angle value and the direction indicator is ±15 degrees while the watch is
horizontal (in relation to the horizon). If the indicated direction is northwest (NW) and 315 degrees, for
example, the actual direction can be anywhere from 300 to 330 degrees.
E-22
Operation Guide 5476
Seconds
Hour
Day
Month
To do this:
Do this:
See page E-13.
See page E-13.
Press E.
Press E.
Use E (+) and B (–).
Direction
Meaning
Direction
Meaning
NE
Northeast
ENE
northeast
SE
Southeast
SSE
southeast
SW
Southwest
WSW
southwest
NW
Northwest
NNW
northwest
4. After all of the settings are the way you want, press A to exit the setting screen.
Note
Minutes
For information about selecting a Home City and confi guring the DST setting, see "Confi guring
Home City Settings" (page E-13).
While the 12-hour format is selected for timekeeping, a P (PM) indicator will appear for times from
noon to 11:59 p.m. No indicator appears for times from midnight to 11:59 a.m. With 24-hour format,
Year
time is displayed from 0:00 to 23:59, without any P (PM) indicator.
The watch's built-in full automatic calendar makes allowances for different month lengths and leap
years. Once you set the date, there should be no reason to change it except after you have the
watch's battery replaced.
The day of the week changes automatically when the date changes.
Refer to the pages shown below for more information on Timekeeping Mode settings.
- Button operation tone on/off: "To enable or disable the button operation tone" (page E-50)
- Illumination duration setting: "To change the illumination duration" (page E-46)
The watch will return to regular timekeeping automatically if you do not perform any operation for
about two or three minutes. Any changes you have made to settings up to that point will be saved.
2. Use E (+) and B (–) to adjust the position of the currently selected hand.
Holding down either button will cause the hand to move at high speed. Once started, high-speed
hand movement will continue even if you release the button. To stop high-speed hand movement,
press any button.
The second hand and mode dial hand will automatically stop high-speed movement after they
complete one revolution. The minute hand will stop automatically after 12 revolutions.
3. Press A to exit home position correction and return to regular timekeeping.
Note
After performing home position adjustment, enter the Timekeeping Mode and check to make sure that the
analog hands and the upper display indicate the same time. If they do not, perform home position
adjustment again.
Bearing Angle to Objective
Bearing to Objective:
Northwest
N: North
E: East
W: West
S: South
See "Digital Compass Readings" (page E-22) for information about how direction readings are
indicated by the watch.
Note
If there is an angle value in the lower display, it means that the bearing memory record (page E-27) is
displayed. If this happens, press E to exit the bearing memory record.
4. To return to the mode you were in immediately before entering the Digital Compass Mode, press D.
To enter the Timekeeping Mode, hold down D for at least two seconds.
Note that performing a digital compass operation while the watch is not horizontal (in relation to the
horizon) can result in large error.
You can calibrate the bearing sensor if you suspect the direction reading is incorrect.
Any ongoing digital compass operation is paused temporarily while the watch is performing an alert
operation (daily alarm, Hourly Time Signal, countdown timer alarm) or while illumination is turned on (by
pressing B). The digital compass operation resumes for its remaining duration after the operation that
caused it to pause is fi nished.
See "Digital Compass Precautions" (page E-30) for important information about taking direction readings.
The direction indicated by the Digital Compass is magnetic north.
You can use Magnetic Declination Correction to confi gure the watch to indicate true north, if you want.
For details, see "Magnetic Declination Correction" below, "To perform magnetic declination correction"
(page E-26), and "Magnetic North and True North" (page E-30).
Calibrating the Bearing Sensor
You should calibrate the bearing sensor whenever you feel that the direction readings being produced by
East-
the watch are off. You can use any one of two different bearing sensor calibration methods: bidirectional
calibration or magnetic declination correction.
South-
Bidirectional Calibration
Bidirectional calibration calibrates the bearing sensor in relation to magnetic north. Use bidirectional
West-
calibration when you want to take readings within an area exposed to magnetic force. This type of
calibration should be used if the watch becomes magnetized for any reason.
North-
Important!
To ensure correct direction readings by the digital compass, be sure to perform bidirectional calibration
before using it. The digital compass may produce incorrect direction readings if you do not perform
bidirectional calibration.
Objective
Bearing Angle Meaning
North
315°
E-17
E-19
E-21
E-23

Advertisement

Table of Contents
loading

Table of Contents