Advertisement
Operation Guide 5098/5099/5101
C (+1 minute) and B (–1 minute) to change the
4.
Use
<Modules 5099 and 5101>
current time setting.
Holding down either button for about two seconds
and then releasing it starts high-speed hand
movement in the applicable direction.
Pressing C and B at the same time will start high-
speed hand movement, which will continue until the
hands complete a 24-hour rotation.
To stop high-speed hand movement, press any
button.
Check the v 24-hour Hand to make sure that the time
is set properly (1:00 a.m. = 1 o'clock,
<Module 5098>
1:00 p.m. = 13 o'clock).
E-30
Using the Minute Counter
The minute counter measures elapsed time.
<Module 5098>
<Modules 5099 and 5101>
E-32
Hand Home Position Adjustment
If the time setting of your watch is not correct even though time calibration signal
reception is being performed normally, use the procedure in this section to check the
home positions of the hands and make adjustments as required.
Note that you do not need to perform the following operation if your watch is showing
the correct time.
Important!
It can take up to 14 minutes for the hands to move to their home positions for hand
home position adjustment. It also can take up to 14 minutes for the hand to return to
their normal positions following hand home position adjustment.
When performing the following procedure, it is recommended that after you move to
a home position, you press B to move the setting back one step. Next, press C to
return it to the home position. This helps to ensure better home position adjustment
accuracy.
E-34
If the current home positions are within ±15 minutes 00 seconds
C (+1 second) and B (–1 second) to adjust the
2.
Use
hand positions so they point to 12 o'clock.
Holding down either button for about two seconds and
then releasing it starts high-speed hand movement in
the applicable direction.
To stop high-speed hand movement, press any
button.
After adjusting the home positions, go to step 4.
E-36
A. This will cause the n Minute Hand (elapsed time) to move to its home
4.
Press
position (0).
If the n Minute Hand (elapsed time) is at the correct home position, advance to
step 6.
<Modules 5099 and 5101>
E-38
Hand Functions
b Ornament
n Minute Hand (elapsed time)
<Module 5098>
5.
After the setting is the way you want, press
This will exit the setting mode and the x Second Hand will resume regular
timekeeping.
For best timekeeping accuracy, press A on a time signal from the TV or radio.
The watch will exit the setting mode automatically if you do not perform any
button operation for about two or three minutes.
To perform an elapsed time operation
B
B
B
Start
Stop
(Restart)
Note
Check the current position of the n Minute Hand (elapsed time). If it is pointed at 5,
for example, it means that fi ve minutes have elapsed.
The minute counter can indicate elapsed time up to 20 minutes.
The b Ornament moves with each second, making one revolution per minute
(60 seconds).
While the minute counter hands are stopped (not moving), press C to reset the
n Minute Hand (elapsed time) to 0.
1.
In the regular timekeeping, hold down
seconds until the c Minute Hand and x Second Hand
move to 12 o'clock.
The x Second Hand goes through the sequence
described below.
Last signal reception result
Keep A depressed until the x Second
setting
Hand starts to move counterclockwise. You can
release A at this time.
The c Minute Hand and x Second Hand are in their
correct home positions if they are pointed precisely
at 12 o'clock. If the hands are in the correct home
positions, advance to step 4.
If the current home positions are greater than ±15 minutes 00 seconds
2. After performing step 1, hold down C and B at the
<Modules 5099 and 5101>
same time until the z Hour Hand, c Minute Hand,
x Second Hand, and v 24-hour Hand all move to 12
o'clock.
C (+1 second) and B (–1 second) to adjust the
3.
Use
hand positions so they point to 12 o'clock.
Holding down either button for about two seconds
and then releasing it starts high-speed hand
movement in the applicable direction.
To stop high-speed hand movement, press any
button.
The v 24-hour Hand is synchronized with the
z Hour Hand and c Minute Hand, so separate
<Module 5098>
adjustment is not required.
After adjusting the home positions, go to step 4.
C (+) and B (–) to adjust the n Minute Hand (elapsed time) so it is at its
5.
Use
home position (0).
Holding down either button for about two seconds and then releasing it starts
high-speed hand movement in the applicable direction.
To stop high-speed hand movement, press any button.
After adjusting the home position, go to step 6.
A to exit home position correction and return to regular timekeeping.
6.
Press
A.
E-31
B
C
(Stop)
Reset
E-33
A for about 10
RC
Current location
E-35
E-37
E-39
Advertisement
