Related Manuals for Bartington Mag613
Summary of Contents for Bartington Mag613
- Page 1 INNOVATION IN MAGNETICS OM2442/2 Operation Manual for Mag613 Eight-Channel Three-Axis Magnetometer Array www.bartington.com...
-
Page 2: Table Of Contents
1. Legal Notices 1.3. Warranty and Terms & Conditions 2. How to Use this Manual 2.1. Symbols Glossary 3. Safe Use 4. Introduction to the Mag613 4.1. Vector Measurements and Conventions 5. Installing the Mag613 5.1. Siting the Magnetometer 5.2. Cable Recommendations 5.3. - Page 3 BARTINGTON INSTRUMENTS 10. Contacts Notes Page 3 of 13 OM2442 iss 2...
-
Page 4: Legal Notices
Goods and Services, which also describe the terms of warranty. They are available at www. bartington.com. Bartington Instruments reserves the right to change any part of the design of these products without prior notice. 2. How to Use this Manual This document describes the installation, function, testing, operation and maintenance of the Mag613 eight channel three-axis magnetometer array. -
Page 5: Safe Use
Consult Bartington Instruments for advice. 4. Introduction to the Mag613 The Mag613 three-axis, eight-head fluxgate is designed to be particularly flexible in use. The main interface cable to the electronics module will not have been fitted with a connector. This allows the user to fit their preferred type, perhaps after the cable has been fitted through a bulkhead or other restricted space. -
Page 6: Installing The Mag613
BARTINGTON INSTRUMENTS 5. Installing the Mag613 5.1. Siting the Magnetometer Note: In whatever situation the Mag613 is to be installed, it is important to avoid or compensate for local magnetic effects. In general: • The magnetometer should be sited several metres from any magnetic base rock to avoid compromising measurements. -
Page 7: Mounting Recommendations
4. Switch on the power supply. 5. For the output: a. Connect a voltmeter to the Mag613 output, i.e. across the analogue output signal and analogue ground. b. Select sensor head and channel by setting the digital address lines correctly (refer brochure DS1854 for address tables). -
Page 8: Using The Mag613
BARTINGTON INSTRUMENTS 6. Using the Mag613 6.1. Magnetic Hysteresis Note: Do not subject your magnetometer to magnetic fields greater than their stated measuring range for extended periods as this could alter the DC offset. If this occurs, the offset will exhibit drift as it returns to its original offset specification. -
Page 9: Troubleshooting
BARTINGTON INSTRUMENTS 7. Troubleshooting Your Mag613 is unlikely to suffer any defects in normal use and it is not user serviceable. Note: Attempting to open any part of the instrument, for any reason, will invalidate your warranty. If you are experiencing problems with your Mag613, which cannot be corrected by following the instructions in the table below, contact the Bartington Instruments Helpdesk. -
Page 10: Care And Maintenance
8.2. Calibration Periodic calibration of the Mag613 is not required. If a fault is suspected, the sensor should be returned to Bartington Instruments for inspection and repair or replacement. 8.3. Storage... -
Page 11: End Of Life Disposal
Electrical and Electronic Equipment (RoHS) and WEEE Regulations current at the time of printing. 10. Contacts Details of how to contact Bartington Instruments Ltd. for aftersales support, technical queries, etc. can be found on the Bartington Instruments website at www.bartington.com. Page 11 of 13... - Page 12 BARTINGTON INSTRUMENTS Notes Page 12 of 13 OM2442 iss 2...
- Page 13 ®The copyright of this document is the property of Bartington Instruments Ltd. Bartington is a registered trademark of Bartington Instruments Limited in the following countries: Australia, Brazil, Canada, China, European Union, India, Israel, Japan, Mexico, New Zealand, Norway, Russia, Singapore, South Korea, Switzerland, Turkey, United Kingdom, United States of America and Vietnam.