Crestron CLW-DIM1 User Manual

Introduction

Features and Functions

The CLW-DIM1 (-DIM1) is a stand-alone wall box
dimmer that can also act as a Cresnet
®
to a Crestron control processor. The CLW-DIM1 has
two preset lighting levels that can be adjusted (refer to
note below). The CLW-DIM1 also includes two isolated,
non-polarized Cresnet wires (plus a ground wire) for
connecting to the Cresnet network over a twisted pair
wire with shield.
NOTE: The two preset levels are noted as Preset 1-High
and Preset 1- Low. "Preset 1-High" is usually used for
turning lights on to full brightness while preset "Preset 1-
Low" is usually used for turning the lights off. Although
"Preset 1-High" and "Preset 1-Low" are usually used for
"On" and "Off" respectively, the light level for each
preset can be customized by the user. Refer to
"Operation" on page 6 for more information on
customizing light levels.
The CLW-DIM1 features a three-position mode selection
switch. Refer to "Operation" on page 6 for more
information. In the absence of Cresnet communications,
the dimmer can still be used to control lighting.
The CLW-DIMS1 (-DIMS1) is similar to the -DIM1 with
the added capability of working with a slave unit
(CLW-SLVD1) in a multi-dimmer / single circuit
application.
The CLW-SLVD1 (-SLVD1) is a slave unit that when
used in conjunction with the -DIMS1 acts as an additional
dimmer control point in a multi-dimmer / single circuit
application. It does not connect to a Cresnet system and
cannot be used without a -DIMS1. The -SLVD1 does not
have a mode selection switch and is not programmable. It
emulates the operation of the -DIMS1 to which it is
connected unless the mode selection switch of the master
is set to "OFF".
These dimmers are available in white, almond, and black.
White units are designated by part numbers ending in
"W". Almond units are designated by part numbers
ending in "A". Black units are designated by part numbers
ending in "B". Each dimmer can be covered with a
decorative faceplate (not supplied).
Crestron Electronics, Inc.
15 Volvo Drive Rockleigh, NJ 07647
Tel: 888.CRESTRON
Fax: 201.767.7576
www.crestron.com
CLW-DIM1, DIMS1, & SLVD1(W/A/B)
®
device that reports

Specifications

Following are specifications for the -DIM1, -DIMS1, and
-SLVD1.
CLW-DIM1, CLW-DIMS1, & CLS-SLVD1 Specifications
SPECIFICATION
Power Requirements
Default Net ID
Switch Type
Load Type
2-Series Control System
1,2
Update File
3
Load Ratings
Incandescent/Tungsten
Halogen
4
Magnetic Low Voltage
Operating Temperature
and Humidity
Dimensions and Weight
1. The latest software versions can be obtained from the Crestron
website. Refer to the NOTE following these footnotes.
2. Crestron 2-Series control systems include the AV2 and PRO2.
Consult the latest Crestron Product Catalog for a complete list of
2-Series control systems.
3. Refer to Derating Charts for Multigang Installations on page 4.
4. VA ratings are for input power to the transformer. If you do not
know the input power requirement of the transformer, use the
bulb's wattage rating to determine proper rating.
NOTE: Crestron software and any files on the website
are for Authorized Crestron dealers and Crestron
Authorized Independent Programmers (CAIP) only. New
users may be required to register to obtain access to
certain areas of the site (including the FTP site).
Installation Guide – DOC. 6250A
DETAILS
Line Power, 120 VAC, 60 Hz
-DIM1: 80
-DIMS1: 81
Dimmer
Incandescent, Tungsten-Halogen,
Magnetic Low Voltage
Version 3.117 or later
-DIM1: 1000W
-DIMS1: 1000W
-SLVD1: N/A
-DIM1: 1000VA/750W
-DIMS1: 1000VA/750W
-SLVD1: N/A
32°F to 104°F (0°C to 40°C)
10 to 90% Relative Humidity
(Non-Condensing)
-DIM1 and -DIMS1:
Height: 4.13 in (10.48 cm)
Width: 2.38 in (6.03 cm)
Depth: 1.91 in (4.85 cm)
Weight: 4.9 oz (0.67 kg)
-SLVD1:
Height: 4.13 in (10.48 cm)
Width: 1.75 in (4.45 cm)
Depth: 1.91 in (4.85 cm)
Weight: 3.6 oz (0.50 kg)
2009754
07.06
Specifications subject to
change without notice.