Table of Contents
Advertisement
20 Descaling
To ensure that your appliance continues to operate cor-
rectly, it must be descaled regularly.
How frequently you need to run the descaling pro-
gramme will depend on the water hardness and how
many times you have used the steam function. The ap-
pliance indicates when only another five or fewer
steam-assisted operations are possible. If you do not
carry out the descaling, you can no longer set any op-
eration with steam.
Descaling comprises several steps and takes approx.
70–95 minutes:
¡ Descaling (approx. 55–70 minutes)
¡ First rinse cycle (approx. 9–12 minutes)
¡ Second rinse cycle (approx. 9–12 minutes)
For reasons of hygiene, the descaling programme must
be run in full.
If descaling is interrupted, you can no longer set any
operation. To ensure that the appliance is ready for op-
eration again, carry out two rinse cycles.
20.1 Preparing descaling
ATTENTION!
The length of time for which the descaler is left to work
is based on the recommended, liquid descaler. Other
descalers may damage the appliance.
Only use the liquid descaler recommended by us
▶
for the descaling programme.
If descaling solution comes into contact with the control
panel or other delicate surfaces, it will damage them.
Remove descaling solution immediately with water.
▶
Mix the descaling solution:
1.
200 ml liquid descaler
‒
400 ml water
‒
Open the control panel.
2.
21 Drying
To prevent residual moisture, dry the cooking compart-
ment following operation.
ATTENTION!
If there is water on the cooking compartment floor
when operating the appliance at temperatures above
120 °C, this will damage the enamel.
Do not use the appliance if there is water on the
▶
cooking compartment floor.
Wipe away any water on the cooking compartment
▶
floor before operation.
21.1 Drying the cooking compartment
You can dry the cooking compartment by hand or use
the "Drying" function.
Allow the appliance to cool down.
1.
Remove dirt from the cooking compartment.
2.
Wipe away the water in the cooking compartment.
3.
Dry the cooking compartment.
4.
Leave the cooking compartment to dry with the
‒
appliance door open for 1 hour.
Remove the water tank and pour the descaling solu-
3.
tion into it.
Once the descaling solution has been poured into
4.
the water tank, slide the tank back in.
Close the control panel.
5.
20.2 Setting the descaling
Requirement: → "Preparing descaling", Page 27
Press
.
1.
Press "Cleaning".
2.
3.
Press "Descaling".
a The duration appears in the display. The duration
cannot be changed.
Press
to start.
4.
a The descaling programme starts and the duration
counts down.
a Once the first part of the descaling programme has
finished, an audible signal sounds. The appliance
prompts you to rinse twice.
To rinse the appliance, for each rinse cycle:
5.
Open the control panel and remove the water
‒
tank.
Thoroughly rinse the water tank and fill it with
‒
fresh water.
Slide in the water tank and close the control
‒
panel.
Use
to start rinsing.
‒
a A signal sounds when each rinse cycle has ended.
Once the second rinsing cycle is complete:
6.
Empty and dry the water tank.
‒
→ "Emptying the water tank", Page 18
Press
to switch the appliance off.
‒
a Descaling is complete and the appliance is ready
for use.
To use the "Drying" function, set "Drying".
‒
→ "Setting the drying process", Page 27
Setting the drying process
Requirement: → "Drying the cooking compartment",
Page 27
Press
.
1.
Press "Cleaning".
2.
Press "Drying".
3.
a The duration appears in the display. The duration
cannot be changed.
Press
to start.
4.
a The drying process starts and the duration counts
down.
a Once the drying process has ended, an audible sig-
nal sounds and the display shows the cooking time
as zero.
Press
to switch the appliance off.
5.
To dry the cooking compartment completely, leave
6.
the appliance door open for 1 to 2 minutes.
Descaling en
27
Advertisement
Table of Contents
