Advertisement
Available languages
Available languages
7.2.UNINSTALLING THE ISOFIX SYSTEM
To free the Top Tether, press the button and pull the tether strap in the opposite direction(the indicator will change from green to red color), in order to take off
the top tether. To free the ISOFIX anchoring, press backwards the ISOFIX System unlock buttons (the indicator will change from green to red color), in order to
free the seat from the vehicle ISOFIX anchoring system.
VIII. INSTALLING Group 1 (9 to 18kg) Install Forward Facing
Ensure the seat is ready to install in forward facing (Group 1) , pull the backrest reclining handle to adjust to angle to position 1, 2 or 3, then release the handle.
It is necessary swivel the seat 180° to place the seat in the direction of travel. Release the backrest rotating handle when the seat is in the desired position.
Locate the ISOFIX arms in the base of the seat.
Place the child safety seat in the back seat of the vehicle facing in the direction of travel.
Hold the child seat with both hands and insert the two ISOFIX arms firmly into the vehicle's ISOFIX anchoring points until they fasten with a click on both sides.
The red button will change to green on both sides .
Shake the seat to check that it is correctly anchored to the vehicle's ISOFIX points.
Pull out the Top Tether and press the tether strap release button to extend the strap until ii is long enough to connect it to the Top Tether anchorage point in the
vehicle. If the Top Tether is lightened favorably and correctly, the button will change to green.
Make sure the 5-point harness of safety seat has been correctly installed.
Open the buckle, put the shoulder harness to the sides, then put the child into the safety seat. Please check if shoulder harness height is equal to your child's
shoulder height, press the adjusting device and pull the shoulder harness to be loose, then press the headrest handle to adjust the shoulder harness to the
suitable position.
Slide the two tongues together into the buckle. The buckle will not work well till you hear "click". Adjust the child restraint belt to make sure the lap belt is well
restrained the child's pelvis. Then tighten the shoulder straps by pulling the adjustable strap at the front of the bottom cushion.
If you want to release your child from the safety seat, press the adjusting device at the front of the bottom, at the same time pull the shoulder straps. Then press
the red button on the buckle, place the shoulder straps at the side and let your child out.
The insertion guides facilitate the installation of the safety seat with the aid of the ISOFIX securing points and prevents damage to the upholstery. When not in
use they should be removed and stored in a safe place. In vehicles with a reclining back the insertion guides should be removed before the seat is reclined.
Problems that may arise are generally the result of accumulation of dirt or foreign bodies in the insertion guides and the clasps. To solve this type of problem
simply clean the part in question.
Note: Use backrest rotating handle to swivel the seat 180° for forward facing installation, backrest hanger and L-backrest hanger are hooked each other.
UNINSTALLING THE ISOFIX SYSTEM
To free the Top Tether, press the button and pull the tether strap in the opposite direction(the indicator will change from green to red color), in order to take off
the top tether. To free the ISOFIX anchoring, press backwards the ISOFIX System unlock buttons (the indicator will change from green to red color), in order to free
the seat from the vehicle ISOFIX anchoring system.
IX. INSTALLATION Group 2/3 (15-36kg) INSTALL REARWARD FACING
Ensure that the child seat's 5-point harness and buckle is removed correctly.
Ensure the seat is ready to install in forward facing (Group 2/3), pull the backrest reclining handle to adjust to angle to position 1 , 2 or 3, then release the handle.
It is necessary swivel the seat 180° to place the seat in the direction of travel. Release the backrest rotating handle when the seat is in the desired position.
Before installing the safety seat, place your child in the seat and adjust the headrest to the correct height. Place the child safety seat in the back seat of the vehicle
facing in the direction of travel. Hold the child seat with both hands and insert the two ISOFIX arms firmly into the vehicle's ISOFIX anchoring points until they
fasten with a click on both sides. The red button will change to green on both sides. Shake the seat to check that it is correctly anchored to the vehicle's ISOFIX
points. Place your child in the safety seat.
Pass the vehicle seat belt through the bottom of the armrest, ensure the lap belt is stretched as low as possible over the child's hips, buckle the vehicle seat belt
until hear a click. Place the diagonal belt through red belt guide hook and must pass the middle between child's shoulder and neck.
The insertion guides facilitate the installation of the safety seat with the aid of the ISOFIX securing points and prevents damage to the upholstery. When not in
use they should be removed and stored in a safe place. In vehicles with a reclining back the insertion guides should be removed before the seat is reclined.
Problems that may arise are generally the result of accumulation of dirt or foreign bodies in the insertion guides and the clasps. To solve this type of problem
simply clean the part in question.
Note: Use backrest rotating handle to swivel the seat 180° for forward facing installation, backrest hanger and L-backrest hanger are hooked each other.
UNINSTALLING THE ISOFIX SYSTEM. To free the ISOFIX anchoring, press backwards the ISOFIX System unlock buttons (the indicator will change from green to red
color), in order to free the seat from the vehicle ISOFIX anchoring system.
X. REMOVE THE FABRIC COVER
Please be sure to use only original seat covers, as the seat cover is important to the proper functioning of the system. Replacement seat covers are available from
your retailer and or at branches. The child seat must not be used without the seat cover.
The cover can be removed and washed with a mild detergent using the washing machine's cycle for delicate items (30 C). Please observe the instructions on the
washing label of the cover. The colours of the cover may fade if washed at more than 300C. Do not spin, and never tumble dry in an electric clothes dryer (the
fabric may separate from the padding). The plastic parts can be cleaned using soapy water. Do not use harsh cleaning agents (such as solvents). The harness can
be removed and washed in lukewarm soapy water Caution! Never remove the buckle tongues from the straps.
XI. ASSEMBLY
ENGLISH
Advertisement
