Advertisement
Available languages
Available languages
3.4. Wash out the harness buckle so that it functions properly once again.
Loosen the 5-point harness of the child seat as much as possible by press the button of the crotch belt. Turn the baby safety car seat to back, unzip the seat cover.
Loosening the shoulder belt in order to access the metal link and connector at the back of the child seat, remove the belt from connector,then remove the
shoulder belt from metal link.
3.5. Then from the front of the child seat, pull out shoulder belt through the slots. Pull below both, the shoulder pads and the belts to the front through he slots.
(front side of the child seat). Remove the shoulder pads from the shoulder belts and put them in the storage bag. Roll the shoulder belts separately on both side
and place them into the fabric cover from the slot of fabric.
3.6. Grasp the metal plate from underneath and turn it into a vertical position. Push upwards and slide the metal plate through the slot. Remove the harness
buckle with the crotch pad and store it in the storage bag.
3.7. CLEANING THE HARNESS BUCKLE: Open the harness buckle (press the red button). Grasp the metal plate from underneath and turn it into a vertical position.
Slide the metal plate through the slot. Remove the harness buckle. Soak the harness buckle in warm water with washing-up liquid for at least an hour. Then
rinse and dry it thoroughly.
IV. ADJUST THE ANGLE OF CHILD SAFETY CAR SEAT
There are 3 levels adjustment in the child safety car seat. Before fixing a child in the child restraint system the seat must be set on the recline position for
rear-facing use.
To achieve that,use the recline handle located in front of the child restraint system between the sitting part and the base to adjust the desired position.
4.1. Use backrest reclining handle to adjust the postion 1,2 and 3 when forward facing installation.
4.2. Adjust the reclining angle to position 3 first, then use backrest rotating handle to swivel the seat 180° for rearward facing installation.
4.3. Total has three level positions: first level, second level, third level
V. ADJUST THE LENGTH OF HARNESS
In order to protect your child much better, fix him/her in the child restraint system and lock the buckle, you should tighten the harness so they are snug and flat
against the child's body,they should never be twisted or loose. To tighter the harness, pull the shoulder belt upwards to remove the slack from the lap sections of
the harness.at the same time to pull the adjuster crotch belt coming from the lock by your another hand. To lengthen the harness,press the button on lock
between the child's two leg.then pull the two shoulder belt simultaneously in your direction, please note while you are doing this hold the harness not the
harness cover.
CAUTION! Check that the harness straps are not twisted and that they have been correctly inserted in the belt slots on the cover.
VI. ADJUSTING THE HEADREST IN AN INSTALLATION WITH A 5 POINT HARNESS. GROUP O+/ 1.
A correctly adjusted harness ensures that the diagonal seat belt section is positioned.and gives your child the optimal protection. The harness must be adjusted
to that there is a space two fingers wide between the harness and your child's body. A Correctly adjusted headrest ensures optimal protection for your child in the
safety seat:shoulder belts are at the same level as your child's shoulders. Pull the headrest handle, the shoulder straps will be moved together.select correct
height and fix them in the correct position for the child by releasing the headrest handle.
ADJUSTING THE HEADREST IN AN INSTALLATION THAT USES THE VEHICLE SAFETY BELT. GROUPS 2/ 3.
A correctly adjusted headrest ensures that the diagonal seat belt section is optimally positioned, and gives your child the optimal protection. The headrest must
be adjusted so that a space equivalent to two fingers remains between the headrest and the child's shoulders.
Pull the headrest handle to adjust headrest to the correct height, then release the headrest handle.Place the safety seat on the car seat.put the child in the seat
and check the height. Repeat the process until the correct height is achieved.
VII. INSTALLATION Group 0+/1 (birth to 18kg) INSTALL REARWARD FACING
WARNING: DON'T USE FORWARD FACING BEFORE THE CHILD'S WEIGHT EXCEEDS 9 KG.
7.1. Check the safety seat is ready to be installed rearward facing(Group 0+/1 ), pull the backrest reclining handle to recline the seat fully, adjust the angle of
recline to position 3, then release the handle. It is necessary swivel the seat 180° to place the seat in the opposite direction of travel . Release the backrest rotating
handle when the seat is in the desired position. Locate the ISOFIX arms in the base of the seat. Place the seat in the back seat of the vehicle in the opposite
direction of travel.
Hold the safety seat with both hands and insert the two ISOFIX arms firmly into the vehicle's ISOFIX anchoring points until they fasten with a click on both sides.
The red button will change to green on both sides. Shake the seat to check that it is correctly anchored to the vehicle's ISOFIX points. Pull out the Top Tether and
press the tether strap release button to extend the strap until it is long enough to connect it to the Top Tether anchorage point in the vehicle. If the Top Tether is
tightened favorably and correctly, the button will change to green. Make sure the 5-point harness of safety seat has been correctly installed. Open the buckle,
put the shoulder harness to the sides, then put the child into the safety seat. Please check if shoulder harness height is equal to your child's shoulder height, press
the adjusting device and pull the shoulder harness to be loose, then press the headrest handle to adjust the shoulder harness to the suitable position.
Slide the two tongues together into the buckle. The buckle will not work well till you hear "click". Adjust the child restraint belt to make sure the lap belt is well
restrained the child's pelvis. Then tighten the shoulder straps by pulling the adjustable strap at the front of the bottom cushion.
If you want to release your child from the safety seat, press the adjusting device at the front of the bottom, at the same time pull the shoulder straps. Then press
the red button on the buckle, place the shoulder straps at the side and let your child out. The insertion guides facilitate the installation of the safety seat with the
aid of the ISOFIX securing points and prevents damage to the upholstery. When not in use they should be removed and stored in a safe place. Problems that may
arise are generally the result of accumulation of dirt or foreign bodies in the insertion guides and the clasps. To solve this type of problem simply clean the part in
question.
ENGLISH
Advertisement
