Related Manuals for Power-flo PFSWCPC75
Summary of Contents for Power-flo PFSWCPC75
- Page 1 OWNER’S MANUAL Series: PFSWCPC75 3/4 HP • 1750 RPM • 60 Hz Submersible Sewage Pump Power-Flo Pumps & Systems • 877-24PUMPS • www.powerflopumps.com ISP No: PFSWC75 - 8/1/15...
-
Page 2: General Safety Information
20 Amp - for 115V or 10 Amp for 230V, fuse or circuit breaker. ® Power-Flo is a registered trademark of Power-Flo Technologies Inc. Alteration Rights Reserved. 3/15, 8/15 Power-Flo Pumps & Systems • 877-24PUMPS • www.powerflopumps.com... -
Page 3: Specifications
EXAMPLE: PFSPCPC3330501T10 - Power-Flo Pumps - Sump Pump - Cast Iron Motor Housing - Plastic Impeller - Cast Iron Suction Plate - 1/3HP - 30” Shut Off Head - 50GPM Max Flow - 115 Volt - Tethered Float - 10’... - Page 4 PFSWCPC75 Series Submersible Sewage Pumps Performance & Dimensions Models: PFSWCPC75201451F10 PFSWCPC75201452F10 ® Power-Flo Pumps & Systems • 877-24PUMPS • www.powerflopumps.com...
- Page 5 EXAMPLE: PFSPCPC3330501T10 - Power-Flo Pumps - Sump Pump - Cast Iron Motor Housing - Plastic Impeller - Cast Iron Suction Plate - 1/3HP - 30” Shut Off Head - 50GPM Max Flow - 115 Volt - Tethered Float - 10’...
- Page 6 PFSWCPC75 Series Submersible Sewage Pumps Performance & Dimensions Models: PFSWCPC75201451T10 PFSWCPC75201452T10 ® Power-Flo Pumps & Systems • 877-24PUMPS • www.powerflopumps.com...
-
Page 7: Pre-Installation
This pump operates automatically. Ball bearings on motor shafts never need lubrication. TOOLS REQUIRED MATERIALS REQUIRED (NOT INCLUDED) Minimum Sump basin: 18 in. diameter, 30 in. depth Power-Flo Pumps & Systems • 877-24PUMPS • www.powerflopumps.com... -
Page 8: Installation
MANUAL - Plug the pump power cord plug into a 115V for 115 V (see Figure 1) or 230V for 230V (see Figure 2) GFCI power outlet directly for manual operation. Pump will start operating once it is pluged into the GFCI outlet and water will drain out. When water is drained out, you must unplug the pump. Power-Flo Pumps & Systems • 877-24PUMPS • www.powerflopumps.com... -
Page 9: Operation
If an electrical failure in the motor is suspected, have it serviced by a competent repairman. Pump is permanently lubricated. No oiling or greasing is required. Power-Flo Pumps & Systems • 877-24PUMPS • www.powerflopumps.com... - Page 10 Use a flathead screwdriver to hold the shaft, then turn the impeller counterclockwise to release the impeller. • Remove debris from around the shaft and on/under the impeller. • Reassemble the pump. Power-Flo Pumps & Systems • 877-24PUMPS • www.powerflopumps.com...
-
Page 11: Troubleshooting
2. Remove obstruction NOTE: Power-Flo Pumps & Systems assumes no responsibility for damage or injury due to disassembly in the field. Disassembly of the pumps or supplied accessories other than at Power-Flo Pumps & Systems or its authorized service centers, automatically voids warranty. -
Page 12: Year Warranty
Some states do not allow the exclusion or limitation of incidental or con sequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state. Power-Flo Pumps & Systems • 877-24PUMPS • www.powerflopumps.com...
Need help?
Do you have a question about the PFSWCPC75 and is the answer not in the manual?
Questions and answers