Eachine 1S Cinefun 75mm 1080P/ 4K Cinewhoop Manual

Features
The lightest 4K Cinewhoop in the World
Powerful and smoothly
Caddx Loris 4K Camera & DVR ready
Runcam Split3-lite 1080P Camera & DVR ready
Betaflight OSD support ,easy to get RSSI, Voltage ,current from your goggles
Camera Angle adjustable
VTX power switchable 25mw~200mw
Specifications
Brand Name: Eachine
Item Name: 1S Cinefun 75mm 1080P/ 4K Cinewhoop
Wheelbase: 75mm
Size: 97mm*97mm*51mm
Weight: 39g(without battery)
Weight:54.5g(with Original 1s 650mah Lipo battery )
Package includes
Item Name
75mm Frame
Option1: CrazybeeX FR V2.2 built-in SPI Frsky receiver
Option2: CrazybeeX FS V2.2 built-in SPI Flysky receiver
Option3: CrazybeeX PNP V2.2 with external TBS Crossfire Nano RX
NC1102 KV19000 motors
HQPROP 1.6x1.6x4 propeller(4cw+4ccw)
Option1:Runcam Split3-lite
Option2:Caddx Loris
Built-in 5.8G 40ch 25mw-200mw VTX
1s 650mah Lipo battery
Propeller disassemble tool
Screwdriver
Flight controller connection diagram
Disconnect the soldering
pad and then you can use
external vtx
BAT+
BUZ-
GND
+5V
TX1
M2
+5V
BOOT M1
LED_STRIP
TX2
IR1
RX2
RX1
M4
M3
GND
GND
BAT+ BIND
M2
TX1
M1
+5V
BOOT
LED_STRIP
IR1
TX2
M4
RX2
GND
M3
GND
RX1
BAT+
BIND
Binding procedure
1. Betaflight 3.5.7 version(Original firmware out of box) binding procedure: Press and hold the
bind button then powering the Cinefun , the Red LED at the bottom of the flight controller
will blinking fast , this indicate the receiver is in bind mode .
Betaflight firmware later than 4.0.1(include)binding procedure: Powering the Cinefun first,
then Press the bind button for 1 second ,the red Led at the bottom of the flight controller will
blinking fast, this indicate the receiver is in bind mode.
2. Another simple way to bind with the Flysky transmitter is : plug the usb and move to the CLI
Command , then type bind code "bind_rx_spi"(for betaflight 4.0.1~4.0.6) or type bind code
"bind_rx"(for betaflight 4.1.X), the receiver will getting into bind mode, and then make your
Flysky transmitter to bind mode, the LED at the bottom of the flight controller will getting to
be solid if bind successfully. (Betaflight 3.5.7 firmware not support these bind code)
Qty
1
1
4
1
1
1
4
1
1
Video in _
GND
Video out _
+5V
Camera
+5V out
+5V
GND
GND
IR1
RX1
BIND
TX1
BOOT
TX2
LED_STRIP
RX2
4K version
1080P version 1080P version
Eachine Cinefun 75MM 1080P/4K FPV Cinewhoop Flysky version
Receiver configuration
Please set Receiver mode to be SPI RX Support from the Configuration tab of the Betaflight
Configurator, then select A7105_Flysky_2A Provider for AFHDS-2A Protocol Radio transmitter
or Select A7105_Flysky Provider for AFHDS Protocol Radio transmitter, don't enable Serial RX
since the Crazybee F4 lite Flight controller is integrated SPI BUS Receiver
Arm/Disarm the Motor
1. The Default Arm/Disarm switch for Cinefun
Betaflight Configurator.
2. Set Arm/Disarm switch for your Flysky Radio: Move to the Aux.channels interface, Set "SWA"
or "SWB" or "SWC" switch etc. for Ch5 to ARM/DISARM the motor.
3 The default channel map for Cinefun Flysky version is AETR1234, please make sure your .
transmitter is matched , otherwise it will can't be armed. Toggle the AUX1 Switch ,the Green LED
on the flight controller will getting to be solid, this indicates the Cinefun was armed . And also you
can found "Armed" displayed on your FPV Goggles or the FPV Monitor. Please make sure keep the
Cinefun level before arming .Be careful and enjoy your flight now!
Toggle the AUX1 Switch, the Green LED on Toggle the AUX1 Switch, the Green LED on
the Flight controller will getting to be solid the Flight controller will getting to be solid
is AUX1(Channel 5),and you can also customize it with