Advertisement
Quick Links
Operation Manual
Tile Cutter
61285
Illustration similar, may vary depending on model
Read and follow the operating instructions and safety information before using for the first time.
Technical changes reserved!
Due to further developments, illustrations, functioning steps and technical data can differ insignific -
antly.
Updating the documentation
If you have suggestions for improvement or have found any irregularities, please contact us.
Advertisement
Related Manuals for WilTec 61285
Summary of Contents for WilTec 61285
- Page 1 Operation Manual Tile Cutter 61285 Illustration similar, may vary depending on model Read and follow the operating instructions and safety information before using for the first time. Technical changes reserved! Due to further developments, illustrations, functioning steps and technical data can differ insignific - antly.
- Page 2 All rights reserved. The WilTec Wildanger Technik GmbH cannot be held accountable for any possible mistakes in this operating manual, nor in the diagrams and figures shown.
- Page 3 Never remove the splitting wedge. The tile cutter is only designed for short-term operation. After 15 min, the machine needs to be switched off for 15 min. © by WilTec Wildanger Technik GmbH Item 61285 Page 3 http://www.WilTec.de http://www.aoyue.eu 2021-1...
- Page 4 This value can change during use as it is dependent on the environment the machine is used in. Protect yourself and others adequately against noise on the basis of this value. © by WilTec Wildanger Technik GmbH Item 61285 Page 4 http://www.WilTec.de...
- Page 5 Guide rail Protective cover for the cut- ting wheel Handle Star grip screw to adjust the angle Star grip screw for safety dur- ing transport 12 Frame © by WilTec Wildanger Technik GmbH Item 61285 Page 5 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 6 5. Fill the basin with water until the cooling water pump is fully submersed. Be careful when filling the basin with water. Make sure you do not touch any electrical equipment with it! © by WilTec Wildanger Technik GmbH Item 61285 Page 6 http://www.WilTec.de...
- Page 7 Always wait until the cooling water has reached the cutting wheel (2)! Move the machine head (29) slowly and smoothly through the tile (9) via the handle. After cutting, turn the tile cutter off. © by WilTec Wildanger Technik GmbH Item 61285 Page 7 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 8 (34). Careful! Left-hand thread! Thus place the key (31) onto the motor shaft and apply a counter- pressure. © by WilTec Wildanger Technik GmbH Item 61285 Page 8 http://www.WilTec.de http://www.aoyue.eu...
- Page 9 Certain cleaning detergents or solutions can damage machine parts made of plastic. These include e. g. petrol, cleaners including chlorine, and household cleaners. Al- ways avoid the use of such chemical cleaners. © by WilTec Wildanger Technik GmbH Item 61285 Page 9 http://www.WilTec.de http://www.aoyue.eu...
-
Page 10: Troubleshooting
Work table dirty Clean the machine. Motor is overheating. Motor overloaded Reduce the engine load. Allow the engine to cool down before continuing to work. © by WilTec Wildanger Technik GmbH Item 61285 Page 10 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de... - Page 11 All WilTec electric devices that fall under the WEEE regulations are labelled with the crossed-out wheeled waste bin logo. This logo indicates that this electric equipment must not be disposed with the domestic waste.