Related Manuals for Ozito SCMS-2125U
Summary of Contents for Ozito SCMS-2125U
- Page 1 SCMS-2125U Original operating instructions Drag, crosscut and miter saw Art.-Nr.: 43.008.16 I.-Nr.: 11039 Anl_SCMS_2125U_SPK7.indb 1 Anl_SCMS_2125U_SPK7.indb 1 02.12.2019 11:24:43 02.12.2019 11:24:43...
- Page 2 14 13 13 14 - 2 - Anl_SCMS_2125U_SPK7.indb 2 Anl_SCMS_2125U_SPK7.indb 2 02.12.2019 11:24:44 02.12.2019 11:24:44...
- Page 3 - 3 - Anl_SCMS_2125U_SPK7.indb 3 Anl_SCMS_2125U_SPK7.indb 3 02.12.2019 11:24:48 02.12.2019 11:24:48...
- Page 4 b 17 9 11 - 4 - Anl_SCMS_2125U_SPK7.indb 4 Anl_SCMS_2125U_SPK7.indb 4 02.12.2019 11:24:52 02.12.2019 11:24:52...
- Page 5 - 5 - Anl_SCMS_2125U_SPK7.indb 5 Anl_SCMS_2125U_SPK7.indb 5 02.12.2019 11:24:56 02.12.2019 11:24:56...
- Page 6 - 6 - Anl_SCMS_2125U_SPK7.indb 6 Anl_SCMS_2125U_SPK7.indb 6 02.12.2019 11:25:01 02.12.2019 11:25:01...
- Page 7 - 7 - Anl_SCMS_2125U_SPK7.indb 7 Anl_SCMS_2125U_SPK7.indb 7 02.12.2019 11:25:08 02.12.2019 11:25:08...
- Page 8 Danger! Read the operating instructions to reduce the risk of inquiry Caution! Wear ear-muff s. The impact of noise can cause damage to hearing. Caution! Wear a breathing mask. Dust which is injurious to health can be generated when working on wood and other materials.
-
Page 9: Safety Regulations
Danger! General safety information for power tools When using the equipment, a few safety pre- cautions must be observed to avoid injuries and Warning! damage. Please read the complete operating Read all the safety information, instructions, instructions and safety regulations with due care. illustrations and technical data provided on Keep this manual in a safe place, so that the in- or with this power tool. - Page 10 e) If you use an electric power tool out- h) Do not allow yourself to be lulled into a doors, use only extension cables that are false sense of security and do not ignore suitable for outdoor use. The use of an the safety regulations covering electric extension cable which is suitable for outdoor power tools, even if you are familiar with...
- Page 11 h) Keep the handles and grip surfaces dry, e) Never cross your hand over the intended clean and free from oil and grease. If the cutting line, either in front of or behind handles and grip surfaces are slippery, it will the saw blade.
- Page 12 Where workpieces are wider or longer eff ect of the saw could cause the saw head to than the table top, make sure that you be pulled down with a jerk, leading to a risk of provide appropriate support for the work- injury.
-
Page 13: Layout And Items Supplied
workbench or a table. Use the holes in the Caution! Take extra care when making double machine‘s base frame to secure the machine. miter cuts. • Bolt the base frame to a workbench or a table. To rectify faults or remove jammed pieces •... -
Page 14: Proper Use
• 27. Knurled screw for cutting depth limiter Hex key 5mm • 28. Stop for cutting depth limiter Hex key 6mm • 29. Adjustment screw for stop 45° to the left Original operating instructions • 30. Adjustment screw for stop 45° to the right Safety instructions 31. -
Page 15: Technical Data
• Catapulting of faulty carbide tips from the saw Operation blade. sound pressure level ......96 dB(A) • Damage to hearing if ear-muffs are not used uncertainty ........3 dB(A) as necessary. sound power level ......109 dB(A) • Harmful emissions of wood dust when used uncertainty ........ -
Page 16: Before Starting The Equipment
5. Before starting the equipment dibly clicks into position. • To release the saw from its position at the bottom, pull the retaining pin (25) out of the Before you connect the equipment to the mains motor mounting while pressing down lightly supply make sure that the data on the rating plate on the machine head (4). -
Page 17: Operation
blade (7) and the turntable (17). stop rail and push the adjustable stop rail • Adjust the adjustment screw (26) until the outwards. • angle between the blade (7) and the turntable The adjustable stop rail (34) must be fixed far (17) equals 90°. - Page 18 handle (1) to move the machine head (4) 6.4 Miter cut 0°- 45° and turntable 0°- 45° (Fig. steadily and with light pressure downwards 1-3, 14) until the saw blade (7) has completely cut The crosscut saw can be used to make miter cuts through the workpiece.
-
Page 19: Replacing The Power Cable
• again by approx. 5 turns. The flange bolt (31) Carry the equipment by the fixed saw table is now accessible for changing the saw blade. (18). • • Press the saw shaft lock (5) with one hand To set up the equipment again, proceed as while positioning the hexagon key 6mm (41) described in section 5.2, 5.3. -
Page 20: Disposal And Recycling
8.2 Carbon brushes In case of excessive sparking, have the carbon brushes checked only by a qualifi ed electrician. Important! The carbon brushes should not be re- placed by anyone but a qualifi ed electrician. 8.3 Maintenance There are no parts inside the equipment which require additional maintenance. - Page 21 For EU countries only Never place any electric power tools in your household refuse. To comply with European Directive 2012/19/EC concerning old electric and electronic equipment and its implementation in national laws, old electric power tools have to be separated from other waste and disposed of in an environment-friendly fashion, e.g.
-
Page 22: Service Information
Service information We have competent service partners in all countries named on the guarantee certifi cate whose contact details can also be found on the guarantee certifi cate. These partners will help you with all service re- quests such as repairs, spare and wearing part orders or the purchase of consumables. Please note that the following parts of this product are subject to normal or natural wear and that the following parts are therefore also required for use as consumables. -
Page 23: Warranty Certificate
Warranty certifi cate Dear Customer, All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the unlikely event that your device develops a fault, please contact our service department at the address shown on this guarantee card. - Page 24 EÚ a noriem pre výrobok Lýsir uppfyllingu EU-reglna og annarra staðla vöru a cikkekhez az EU-irányvonal és Normák szerint a következő konformitást jelenti ki Drag, crosscut and miter saw SCMS-2125U (Ozito) 2014/29/EU 2006/42/EC Annex IV 2005/32/EC_2009/125/EC Notifi ed Body: 2014/35/EU Reg.
- Page 25 - 25 - Anl_SCMS_2125U_SPK7.indb 25 Anl_SCMS_2125U_SPK7.indb 25 02.12.2019 11:25:15 02.12.2019 11:25:15...
- Page 26 - 26 - Anl_SCMS_2125U_SPK7.indb 26 Anl_SCMS_2125U_SPK7.indb 26 02.12.2019 11:25:15 02.12.2019 11:25:15...
- Page 27 - 27 - Anl_SCMS_2125U_SPK7.indb 27 Anl_SCMS_2125U_SPK7.indb 27 02.12.2019 11:25:15 02.12.2019 11:25:15...
- Page 28 EH 12/2019 (01) Anl_SCMS_2125U_SPK7.indb 28 Anl_SCMS_2125U_SPK7.indb 28 02.12.2019 11:25:15 02.12.2019 11:25:15...
Need help?
Do you have a question about the SCMS-2125U and is the answer not in the manual?
Questions and answers