Terminal Data For The Power Cables - ABB ACH580-01 Quick Installation And Start-Up Manual

ACH580-
Nominal ratings
01-...
Input Output
current current
I I
1 2
A A
144A-6 144 144
192A-6 192 192
242A-6 242 242
271A-6 271 271
1) Typical motor power with no overload capacity (nominal use). The kilowatt ratings apply to most IEC 4-pole motors. The
horsepower ratings apply to most NEMA 4-pole motors.
2) For IEC installations, ABB recommends aR fuses. See hardware manual for guidelines in selecting between aR and gG
fuses, and for additional fuse alternatives.
3)The recommended branch protection fuses must be used to maintain the IEC/EN/UL 61800-5-1 and CSA C22.2 No. 274
certifications. Refer to note 5 for circuit breaker protection.
4) IEC 61439-1: The drive is suitable for use on a circuit capable of delivering not more than 65 kA when protected by the
fuses given in this table.
5) UL 61800-5-1, CSA C22.2 No. 274: The drive is suitable for use on a circuit capable of delivering not more than 100 kA
symmetrical amperes (rms) at 600 V maximum when protected by the ABB recommended fuses.
Alternate Fuses, MMPs and Circuit Breakers for ABB Drives
6) Refer to
and circuit breakers that can be used as branch circuit protection.
7) Class J, CC, and CF fuses are also allowed at the same nominal current and voltage ratings.
8) IEC Installations: The cable sizing is based on max. 9 cables laid on a cable ladder side by side, three ladder type trays one
on top of the other, ambient temperature 30 °C, PVC insulation, surface temperature 70 °C (EN 60204-1 and IEC 60364-5-
52/2001). For other conditions, size the cables according to local safety regulations, appropriate input voltage and the load
current of the drive.
9) NEC Installations: The cable sizing is based on NEC Table 310-15 for copper wires, 75 °C (167 °F) wire insulation at 40 °C
(104 °F) ambient temperature. Not more than three current-carrying conductors in raceway or cable or earth (directly
buried). For other conditions, size the cables according to local safety regulations, appropriate input voltage and the load
current of the drive.

Terminal data for the power cables

Frame T1/U, T2/V, T3/W, L1, L2, L3, R-, R+/UDC+
size Min. wire size (solid/
stranded)
2
mm AWG
R1 0.2/0.2 24
R2 0.5/0.5 20
R3 0.5/0.5 20
R4 0.5/0.5 20
R5 6 10
R6 25
R7 95 3/0
R8 2×50 2×1/0
R9 2×95 2×3/0
1) In 400/480/575 V drives, cable lug or cable clamp is used for grounding.
Notes:
•
The minimum specified wire size does not necessarily have sufficient current carrying capacity at maximum load.
•
The maximum number of conductors per terminal is 1 except where indicated.
Motor gG fuse
1)
power (IEC 60269)
P
n
ABB type
kW hp
110 150 -
150 200 -
180 250 -
180 250 -
Max. wire size (solid/
stranded)
2
mm AWG
6/4 10
16/16 6
35/35 2
50 1
70 2/0
4 150 300 MCM
240 500 MCM
2×150 2×300 MCM
2×240 2×500 MCM
3)
Fuses
uR/aR UL class
2)4) 5)6)7)
fuse T
(DIN 43620)
Bussmann type
- JJS-250
- JJS-300
- JJS-400
- JJS-400
(3AXD50000645015
Tightening torque Max. wire size (solid/
2
N·m lbf·ft mm
1.0 0.7 16/16
1.5 1.1 16/16
3.5 2.6 35/35
4.0 3.0 35/35
5.6 4.1 35/35
1)
30 22.1 180
1)
40 29.5 180
40 29.5 2×180
70 51.6 2×180
Typical power cable sizes,
Cu
2 8) 9)
mm AWG
- 4/0
- 300 MCM
- 500 MCM
- 2x250
MCM
[English]) for additional UL fuses
PE
Tightening torque
stranded)
AWG N·m
6 1.5
6 1.5
2 1.5
2 1.5
2 -
1) 1)
350 MCM 9.8
1) 1)
350 MCM 9.8
1) 1) 1)
2×350 MCM 9.8
1) 1) 1)
2×350 MCM 9.8
14
Frame
size
R8
R9
R9
R9
lbf·ft
1.1
1.1
1.1
1.1
1.6
1)
7.2
1)
7.2
1)
7.2
1)
7.2