Vitek VT-3505 SR Manual Instruction page 4

ENGLISH
sures and information about danger that can be
caused by improper usage of the unit.
THE UNIT IS INTENDED FOR HOUSEHOLD USAGE
ONLY
Instruction manual
Installation of batteries
• Open the battery compartment lid (14) and insert
a CR2032 3V battery (not supplied), following the
polarity.
• Close the battery compartment lid (14).
Attention!
Battery leakage can cause injuries or damage of the
unit. To prevent unit damages, follow the recommenda-
tions specified below:
• insert the battery properly;
• take the battery out if you are not going to use the
unit for a long time;
• do not recharge or dismantle the battery, do not ex-
pose it to high temperature;
• change the battery in proper time.
Note:
The unit is intended to be powered by mains; battery
supply is a backup power source. Battery allows to save
settings of current time in case of AC supply voltage
interruption.
Take the battery out if you are not going to use the unit
for a long time.
Connecting the unit to the mains
Before connecting the unit to the mains, make sure that
your home mains voltage corresponds to unit operating
voltage.
Insert the power plug into the mains socket.
Current time and date setting
In the current time mode press and hold the button (11)
«MEM/M+» for more than 2 second to switch to current
time and date setting mode.
• The year digits will start flashing on the display. Use
the buttons (2) ◄◄ and (6) ►► for setting the year.
• Press the button (11) «MEM/M+». The month digits
will start flashing on the display. Use the buttons (2)
◄◄ and (6) ►► for setting the month.
• Press the button (11) «MEM/M+». The day digits
will start flashing on the display. Use the buttons (2)
◄◄and (6) for setting the day.
• Press the button (11) «MEM/M+». Time format sym-
bols will start flashing on the display: 24 hours or 12
hours. Use the buttons (2) ◄◄ and (6) ►► to se-
lect the time format.
• Press the button (11) «MEM/M+». The hour digits
will start flashing on the display.
• Use the buttons (2) ◄◄ and (6) ►► to select the
necessary hour.
• Press the button (11) «MEM/M+». The minute digits
will start flashing on the display. Use the buttons (2)
◄◄ and (6) ►► for setting the minutes.
VT-3505_IM.indd 4
Note: If buttons (2) ◄◄ and (6) ►► are not pressed
within 2 seconds, the unit will be switched to the current
time mode.
Date displaying
In the current time mode press the button (2) ◄◄ to
view the date; to view the year press the button (6) ►►.
The unit will be switched to the current time mode in 5
seconds.
Setting a clock to summer time
Press and hold the button (2) ►► for more that 3
seconds to switch the clock to summer time and back.
Setting temperature measurement units (C/F)
Press and hold the button (6) ◄◄ for more than 3 sec-
onds to select temperature measurement units (C/F).
Listening to the radio
1. To switch the radio on press the button (12)
Use the buttons (2) ◄◄ and (6) ►► for tuning to the
desired radio station.
Note: For the best radio stations reception in the FM-
band it is recommended to unwind the FM-antenna
cable and place it optimally.
Manual tuning: consequently press the buttons (2)
◄◄ and (6) ►► to select the desired radio station with
step 0.1 MHz in FM mode.
Auto tuning: press and hold the button (2) ◄◄ or (6)
►► for more than 2 seconds. The tuner shall begin
scanning and automatically stops after finding the clos-
est strong signal from radio station.
2. After you stop listening press the button (12)
Radio stations programming
You can set up and save 10 radio stations in FM band.
• Tune to the station you want to program.
• Press and hold the button (11) «MEM/M+» until a
flashing symbol of «Р01» appears.
• Consequently press the buttons (2) ◄◄ or (6) ►►
to select the number of programming cell.
• Press the button (11) «MEM/M+» again to save the
settings.
• Repeat steps 1–4 for all radio stations that you wish
to save in the clock radio memory.
• To select the preliminary programmed radio stations
press the button (11) consequently in radio mode.
Antenna (17)
Select the antenna (17) position for quality reception
of radio signal.
Volume level adjusting
Use buttons (8) "-" and (9) "+" to set up the desired
volume level.
Alarm time setting (AL.1 and AL.2)
In the current time mode press and hold the button (1) for
more than 2 seconds to switch to alarm time setting mode.
4
.
again.
17.12.2013 12:20:20