ABLE OF ONTENT BEFORE YOU BEGIN... 3 ... 3 HAT IS INCLUDED ... 3 NPACKING NSTRUCTIONS AC P ... 3 OWER ... 3 AFETY NSTRUCTIONS INTRODUCTION ... 4 ... 4 EATURES ... 4 OREWORD ... 5 OMPONENTS VERVIEW INSTALLATION... 6 ...
EFORE EGIN What is included 30ft roll of blue or red COLORflex™ 2 pieces of the following items; Power cord/converter, End cap, Splice connector 15 Channel mounting clips Unpacking Instructions Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that all parts are present, and have been received in good condition.
One such item to draw special attention to is the PVC glue. CHAUVET does not provide PVC glue with the accessories enclosed. This item is continuously illustrated in all pictures and is an integral component for maintaining water-tight connections.
Components Overview MCP-3 MCP-2 CF-NEON(x) User Manual LEDCF-POWER 1. Power cord and plug with AC/DC Recommended tools for installation and repairs converter Use male connector pin (MCP-2) LEDCF-SPLICE 1. Male connector pin (MCP-3) 2. Heat shrink tube LEDCF-CAP 1. End cap LEDCF-CLIP 1.
NSTALLATION The COLORflex™ LED Neon is a versatile and user friendly linear lighting device; it can be cut and bent and formed in the field and easily installed on flat surfaces of varied materials, such as wood, plastic, steel, or on walls to form all kinds of pattern according to your design. Please follow the following pre-installation guidelines;...
Appendix 90° Installation Continuous 90° run. 90° run using the L connector. 180° Installation Other installation illustrations Convex Installation Concave Installation Slotted Installation Capping off run CF-NEON(x) User Manual 2004-09-20/15:32...
EPAIR NSTRUCTIONS STEPS Wear anti-static strap (Part A) or a similar device and connect it to earthed metal equipment. Insert another end of needle like connector (Part C) into LED Neon to locate the problematic point. If the problem section lights up then the faulty point has been located.
Page 9
Unplug the power source. Use cutter (Part D) and pincer (Part E) to open up the PVC and fix the faulty parts inside. Re-solder the components (Part F & G). Plug in the power source to re-confirm the faulty part is fixed. CF-NEON(x) User Manual Appendix 2004-09-20/15:32...
Page 10
Put back all of the parts into the LED Neon-Flex. Use heater (Part B) to soften the PVC. Use flat & clean materials to press on the softened PVC to make the opening stick back. Use cutter (Part D) to cut off the excessive PVC.
Package must be clearly labeled with a Return Merchandise Authorization Number (RA #). Products returned without an RA # will be refused. Call CHAUVET and request RA # prior to shipping the fixture. Be prepared to provide the model number, serial number and a brief description of the cause for the return.
CF-NEONR30 – Red ... 1.44W per foot CF-NEONB30 – Blue ... 2.00W per foot CUTTING UNITS CF-NEONR30 – Red ... 2.5 feet (76 cm) CF-NEONB30 – Blue ... 1.5 feet (45.7 cm) ORDERING INFORMATION CF-NEONR30... COLORflex™ LED Neon Red CF-NEONB30...COLORflex™ LED Neon Blue ACCESSORIES LEDCF-POWER ...Power cord with AC/DC converter...
If this product is not covered under the terms of this warranty, CHAUVET will advise you of the costs to carry out any repairs necessary and the unit will be shipped to you on receipt of payment for the work including the return freight charges.
Need help?
Do you have a question about the CF-NEONB30 and is the answer not in the manual?
Questions and answers