CT3EQ COLOR ™ TUBE Snapshot 3.0 EQ ONTROLLER Use on Dimmer Outdoor Sound-Activated Master/Slave Autoswitching Power Supply External Power Supply Replaceable Fuse User-Serviceable User Manual (Optional)
Make sure the power cord is never crimped or damaged. · Never disconnect the power cord by pulling or tugging on the cord. · Avoid direct eye exposure to the light source while it is on. Page 4 of 22 COLORtube™ 3.0 EQ User Manual Rev. 3...
Built-in sound activated programs via DMX (36 different color combinations) Addi t i o na l Fe at ur e s · Controls up to 225 tubes · Addresses each tube automatically COLORtube™ 3.0 EQ User Manual Rev. 3 Page 5 of 22...
Product Overview (CT3EQ Controller) Microphone DMX LED indicator MODE ENTER button button DOWN button button Power Switch DMX Out Sound DMX In Sensitivity Signal Output DC Power to Tubes Input Page 6 of 22 COLORtube™ 3.0 EQ User Manual Rev. 3...
Product Overview (COLORtube™ 3.0 EQ) Front Side Back Side Signal In Power Out Power In Signal Out Power Indicator DIP Switches Sound Sensitivity Microphone COLORtube™ 3.0 EQ User Manual Rev. 3 Page 7 of 22...
Always connect the fixture to a circuit with a suitable electrical ground. Fixture Linking (COLORtube™ 3.0 EQ) The COLORtube™ 3.0 EQ has both signal and power linking. Please see the diagram below for a description on how to link these fixtures.
Mounting Orientation The COLORtube™ 3.0 EQ may be mounted in any safe position. Rigging Mount the fixture securely. This may be done with a screw, nut and bolt, or a hanging clamp. The hole in each bracket is 13 mm in size. When rigging consider routine maintenance and DIP switch access. Please see the following steps for installation.
Maximum recommended number of fixtures on a serial data link: 32 Data Cabling To link fixtures together you must obtain data cables. You can purchase CHAUVET-certified DMX cables directly from a dealer/distributor or construct your own cable. If you choose to create your own cable please use data-grade cables that can carry a high quality signal and are less prone to electromagnetic interference.
3-Pin to 5-Pin Conversion Chart If you use a controller with a 5-pin DMX output connector, you will need to use a 5-pin to 3-pin adapter. CHAUVET Model No: DMX5M, or DMX5F. The chart below details a proper cable conversion:...
In addition, you should note the starting address selected for future reference. The COLORtube™ 3.0 EQ fixture uses six DMX channels. If this is your first time using DMX, we recommend reading the “DMX Primer” section in the “Appendix”.
Automatically detect the quantity of tubes FIND TUBES connected in the series For best results, first power on all of the tubes at the same time (simultaneously), and then power on the controller. COLORtube™ 3.0 EQ User Manual Rev. 3 Page 13 of 22...
Run Speed Mode 22~34 000~255 000~005 No Strobe 174~249 See Chart Below Run Speed 006~255 Strobe Sound Sound 250~255 Activity Color No Function No Function See Chart Below Change Page 14 of 22 COLORtube™ 3.0 EQ User Manual Rev. 3...
Back: B Active: RB 105~111 SYNC CROSS 238~244 Back: B Active: W 112~118 CYCLE COLORS 245~251 Back: W Active: R 119~125 AUTO MOTION 252~255 Back: W Active: G 126~132 COLORtube™ 3.0 EQ User Manual Rev. 3 Page 15 of 22...
· Install an optically coupled DMX splitter after unit #32. · Keep DMX cables separated from power cables or · Interference from AC wires black lights. If you still have a problem after trying the above solutions, please contact CHAUVET Technical Support. Contact Us World Headquarters United Kingdom &...
XLR male to female connectors. The shield connection is pin 1, while pin 2 is Data Negative (S-) and pin 3 is Data positive (S+). CHAUVET carries 3-pin XLR DMX compliant cables, DMX-10 (33’), DMX-4.5 (15’) and DMX-1.5 (5’) General Maintenance To maintain optimum performance and minimize wear, fixtures should be cleaned frequently.
Package must be clearly labeled with a Return Merchandize Authorization Number (RMA #). Products returned without the RMA # will be refused. Call CHAUVET and request an RMA # prior to shipping the fixture. Be prepared to provide the model number, serial number and a brief description of the cause for the return.