Checking For Gas Leaks; Prior To Use; Lighting The Burners - Campingaz ADELAIDE PLANCHA TTL Operation And Maintenance

- Use two wrenches to tighten the flexible hose on
the gas end piece:
a number 14 wrench to immobilize the
device input connection,
an adjustable wrench to tighten the flexible
hose nut.
- check for leaks following the instructions in paragraph f).
Check that the flexible hose stretches out normally
without twisting or pulling and does not come into contact
with the hot sides of the barbecue. It should be replaced
when the expiry date on the hose is passed or whenever
it is damaged or develops surface cracks.
Belgium, Luxembourg, United Kingdom, Ireland,
Portugal, Spain, Italy, Croatia, Greece, Netherlands,
Czech Republic, Slovakia, Hungary, Slovenia, Norway,
Sweden, Denmark, Finland,
Romania, Poland, Switzerland, Estonia:
The barbecue is equipped with a circular connector. It
should be used with flexible hose that is suitable for use with
butane and propane gas. Hose length should not exceed
1.20 metre. It should be replaced if it is damaged or
cracked, when required by national regulations or at the
end of the part lifecycle. Do not pull or pierce the hose.
Keep away from any parts of the barbecue that get hot.
Check that the flexible hose stretches out normally,
without twisting or pulling.
Germany, Austria:
The barbecue should be used with flexible tubing that is
suitable for use with butane and propane gas. Hose
length should not exceed 1.50 metre. It should be
replaced if it is damaged or cracked, when required by
national regulations or at the end of the part lifecycle. Do
not pull or pierce the tubing. Keep away from any parts of
the barbecue that get hot. Check that the flexible hose
stretches out normally, without twisting or pulling.
Flexible tubing connection: to connect the tubing to the
connector on the barbecue, tighten the nut on the tubing
firmly but without excess force using the two wrenches
provided:
no. 14 wrench to tighten the connector
no. 17 wrench to tighten the nut on the tubing
f) CHECKING FOR GAS LEAKS
1) Work outside, away from all sources of ignition. Do not
smoke.
2) Make sure the control knobs are in the "off" ( )
position.
3) Connect the flexible tubing to the connector and
barbecue as described in part e).
4) Fit the regulator onto the gas cylinder in accordance
5) Use a gas leak solution to test for leaks. Important:
6) Apply the solution to the connections cylinder/regulator/
7) Bubbles in the gas leak solution indicate that there are
8) The leak can be stopped by tightening any hose
9) Close the valve on the gas cylinder.
Important:
Check for leaks at least once per year and each time the
gas cylinder is replaced.
Bulgaria, Turkey,
g) PRIOR TO USE
Never use the barbecue until the instructions have been
read carefully and understood. Also, make certain that:
- there are no leaks
- the venturi tubes are not blocked (example: spider
- the hose does not touch any components which may get
- that the hood has been removed (depending on model)
- This device has a large number of vents to optimize the
h) LIGHTING THE BURNERS
Read steps 1 to 5 before beginning with step 1.
1 - Make sure that the control knobs are in the "OFF"
2 - Open the gas cylinder valve.
3 - Push down on one of the
4 - When the first burner has
5 - If the device still does not light, place the control knob
Important:
If the burner fails to light after the second attempt, turn the
control knob to the "off" position ( ) and check that the
burner outlets and the venturi tube are not blocked.
13
with its instructions.
never use a naked flame to check for gas leaks.
hose/apparatus (the control knobs should remain
closed: off position ( )). Open the gas cylinder valve.
gas leaks.
connection or replacing any faulty component. The
barbecue must not be used until the leak is stopped.
webs)
hot.
device use. Be sure that these vents are not blocked.
position ( ).
control knobs and turn it to
the "HI" position ( ). You
will hear a "click": a spark is
produced that triggers
lighting of the burner. If the
burner does not light, turn
the knob to the "OFF" ( )
position and repeat the two
steps.
been lighted, repeat the operation for the second
burner.
in the "OFF" ( ) position and wait 5 minutes before
starting the operation again.
GB