Chicco ALYSIA Manual page 16

booklet refer to a specific version of the stroller. Some of the
components and functions described here may vary depend-
ing on the model purchased.
ASSEMBLING THE STROLLER
1. Press button A and then press button B (Fig 1); at the same time
extend the structure until you hear the locking click (fig. 1A-1B).
2. Insert the front wheel in the dedicated hole until you hear
the locking click (fig. 2). Repeat the same operation for the
second front wheel.
3. To assemble the rear wheels insert the wheel pin in the rear
leg tube (fig. 3). Repeat the same operation for the other
wheel.
To remove the front and rear wheels press the release mecha-
nisms in figures 3A-3B.
WARNING: Before using the stroller, make sure that the wheels
are firmly attached to the structure by pulling gently outwards.
WARNING: When opening the stroller, ensure that your child
and any other children are at a safe distance. Make sure that
during these operations the moving parts of the stroller do not
come into contact with your child.
CARRY-ALL BASKET
4. To attach the basket to the stroller, wrap and close the velcro
on the front tube (Fig. 4) then wrap the fabric straps in the
appropriate spaces on the front legs and fasten them with
the buttons (Fig. 4A-4B).
To fasten the rear section, wrap and close the velcro in the slot
located on the rear tube of the stroller (Fig. 4C).
FITTING/REMOVING THE SEAT LINING
The lining must be fitted with the seat disengaged from the
stroller.
5. Before you start fitting the lining, insert the legrest tube into
its fabric slot (Fig. 5).
6. Place the fabric on the seat frame and, on the back, close
the horizontal zipper wrapping the tube (Fig. 6-6A). Before
closing the zip on the rear tube, make sure that the waist
strap is always inserted into the two vertical fabric slots and
runs through the two side slots (Fig. 6B). Then pass the crotch
strap through the slot (Fig. 6C).
WARNING: Pull the crotch strap upwards to make sure it is
properly secured.
7. Cover the backrest by wrapping it with the fabric and closing
the zipper on the back (Fig. 7).
8. Attach the seat fabric to the frame with the two respective
buttons positioned on the sides (Fig. 8).
9. Insert the legrest tube in the dedicated slots until they click
into place (Fig. 9).
10. Place the cushion on the seat by passing the crotch strap
through the slot (Fig. 10) and fastening it to the fabric un-
derneath with the two buttons (Fig. 10A).
The seat could already be used in this configuration; however,
there is also a reducer cushion for the backrest.
11. To fit the reducer cushion, pass the belts through the upper
slots (Fig. 11) and the waist belt through the side slots (Fig.
11A); fasten the rear part with the snap buttons (Fig. 11B).
To remove the lining, follow the same steps in the reverse order.
WARNING: After removal of the safety harness (e.g. for wash-
ing), ensure that the harness is reassembled correctly using the
anchorage points. The harness must be re adjusted. To ensure
that the harness is adjusted correctly, fitting your child and
securely closed, pull firmly on the end of the harness (on the
underside of the seat).
COMFORT KIT
The Comfort Kit comprises 2 shoulder straps and crotch strap.
12. Insert the shoulder pads on the straps and insert the buckle
in the padded crotch strap (Fig. 12-12A).
STROLLER SAFETY HARNESS
13. The stroller comes with a five-point safety harness which
consists in two shoulder straps, a waist strap and a crotch
strap with a buckle.
WARNING: when using with children aged 0 to 6 months, you
may have to shorten the length of the straps to adjust them to
your baby; in this case, use the shoulder straps, passing them
first through the two horizontal adjustment holes and then
pass the waist strap through the two vertical adjustment holes
(Fig. 13-13A) in the same way.
WARNING: the use is the same both in winter configuration
(with reducer cushion) and in the summer version (without re-
ducer cushion).
14. Make sure the shoulder straps are at a suitable height for
your child. if they are not, adjust their height and repeat the
same operation for the waist strap as well (fig. 14).
15. Fasten the straps by passing the waist clip (A) through the
buckle on the shoulder strap (B), and secure in the crotch
strap buckle (C) (Fig. 15).
To release the waist strap, remove the prongs from the buckle
by pressing on the ends.
WARNING: To ensure the safety of your child, you must use
the crotch strap, waist belt and safety harness at the same time.
WARNING: After removal of the safety harness (e.g. for wash-
ing), ensure that the harness is reassembled correctly using the
anchorage points. The harness must be re adjusted.
BUMPER BAR
16. The seat features a bumper bar. To attach the bar, insert it
in the slots near the joint (Fig. 16) and check that the bar
is firmly in place by pulling it towards you. To pull out the
bumper bar, press the two buttons at the extremities (Fig.
16A) and pull it out. You can release one side of the bumper
bar to easily seat your child. The bumper bar can be used
both forward facing and parent facing.
WARNING: Always fasten your child with the safety harnesses.
The BUMPER bar IS NOT a device for containing your child.
WARNING: Never use the bumper bar to lift the stroller up
with your child sitting in it.
FITTING THE SEAT ON THE STROLLER
17. To attach the stroller seat, insert it in the relevant metal
fasteners until you hear the click which confirms that it has
been fastened (Fig. 17). To make it easier to attach the seat
to the stroller there are guide slots showing you the correct
alignment of the seat with the metal fasteners (fig. 17A). The
seat can be attached both forward facing (fig. 17B) and par-
ent facing (fig. 17C).
WARNING: Before using, make sure that the seat is properly
locked on by pulling it upwards.
WARNING: If it is not properly fastened, remove it using the
release buttons and repeat the step. Otherwise contact the
Chicco customer service.
18. To release the seat, use the buttons on the joints of the seat.
Press the small button A and, at the same time, push down
the central button B (Fig. 18-18A); once this step is done, lift
the seat for complete release (Fig. 18B).
WARNING: The child must never be sitting in the seat when
fastening/unfastening it.
ADJUSTING THE BACKREST
19. Press the button on the back of the stroller backrest to re-
cline it to the desired position (Fig. 19). Release the button
and the backrest will click into the closest lock position.
16