Moxa Technologies NPort 5200-P Series Quick Installation Manual

NPort 5200-P Series
Quick Installation Guide
Second Edition, July 2006
1. Overview
Welcome to the programmable NPort 5200-P series, a compact
palm-sized data communication device that allows you to control RS-232
(NPort 5210-P) or RS-232/422/485 (NPort 5230-P) serial devices over a
TCP/IP-based Ethernet.
2. Package Checklist
Before installing the NPort 5210-P/5230-P, verify that the package
contains the following items:
NPort 5210-P/5230-P
1 NPort 5210-P/5230-P 2-port Serial Device Server
Optional Accessories
DK-35A DIN-Rail Mounting Kit (35 mm)
CBL-RJ45M9-150 RJ45 (8-pin) to DB9 (M) cable, 150 cm
CBL-RJ45F9-150 RJ45 (8-pin) to DB9 (F) cable, 150 cm
CBL-RJ45M25-150 RJ45 (8-pin) to DB25 (M) cable, 150 cm
CBL-RJ45F25-150 RJ45 (8-pin) to DB25 (F) cable, 150 cm
DIN-Rail Power Supply and Adaptor
NPort 5210-P-ST/5230-P-ST
1 NPort 5210-P/5230-P 2-port Serial Device Server
Documentation & Software CD
NPort 5210-P/5230-P Series Quick Installation Guide
Switching power adapter
Power Jack to Terminal Block Cable
Power Cord
Product Warranty
Turbo C Linense Card
RJ45 to RJ45 Ethernet cross-over cable
CBL-RJ45M9-150 x 2 (NPort 5210-P-ST Only)
Notify your sales representative if any of the above items is missing or
damaged.
— 1 —
3. Hardware Introduction
As shown in the following figures, NPort 5210-P has two 8-pin RJ45
ports, both for the RS-232 interface, NPort 5230-P has one 10-terminal
terminal block, with 5 pins used for one RS-232 port, and 5 pins used for
one RS-422/485 port.
NPort 5210-P
RJ45 10/100 Mbps
Ethernet port
V- V+
12-48V
Ready
Link
P1
P2
Port 1
RS-232
RJ45 (8-pin) serial ports
Reset Button—Press the Reset button continuously for 5 sec to load
factory defaults: Use a pointed object, such as a straightened paper clip or
toothpick, to press the reset button. This will cause the Ready LED to
blink on and off. The factory defaults will be loaded once the Ready LED
stops blinking (after about 5 seconds). At this point, you should release
the reset button.
P/N:1802052003000
NPort 5230-P
Terminal Block
Reset button
Power input
V- V+
RESET 10/100M RESET 10/100M
Ethernet 12-48V Ethernet
DIN-Rail
screw hole Ready
Link
P1
P2
5230-P
5210-P
Industrial RS-232/422/485 Device Server
Industrial RS-232 Device Server
Wallmount
P1 RS-232 P2 RS-485/422
screw hole
Port 2
RS-232
RS-232 & RS-422/485
Terminal Block
— 2 —
LED Indicators—The top panels of NPort 5210-P/5230-P have four
LED indicators, as described in the following table.
LED Name LED Color
red
Ready
green
off
orange
green
Link
off
orange
5210
green
P1, P2
off
4. Hardware Installation Procedure
STEP 1: After removing NPort 5210-P/5230-P from the box, the first
thing you should do is connect the power adaptor. Connect the 12-30
VDC power line with NPort 5210-P/5230-P's terminal block, or connect
the DIN-Rail power supply with NPort 5210-P/5230-P's terminal block.
STEP 2: Connect NPort 5210-P/5230-P to a network. Use a standard
straight-through Ethernet cable to connect to a Hub or Switch. When
setting up or testing NPort 5210-P/5230-P, you might find it convenient
to connect directly to your computer's Ethernet port. In this case, use a
cross-over Ethernet cable.
STEP 3: Connect NPort 5210-P/5230-P's serial port to a serial device.
STEP 4: Placement Options
In addition to placing
NPort 5210-P/5230-P
on a desktop or other
horizontal surface, you
may also make use of
the DIN-Rail or Wall
Mount options, as
illustrated here.
LED Function
Steady on: Power is on and NPort 5200-P
series is booting up.
Blinking: Indicates an IP conflict, or
DHCP or BOOTP server did
not respond properly.
Steady on: Power is on and NPort 5200-P
series is functioning normally.
Blinking: The device server has been
located by Administrator's
Location function
Power is off, or power error condition
exists.
10 Mbps Ethernet connection.
100 Mbps Ethernet connection.
Ethernet cable is disconnected, or has a
short.
Serial port is receiving data.
Serial port is transmitting data.
No data is being transmitted or received
through the serial port.
Wall Mount DIN-Rail
V- V+ RESET 10/100M
12-30V Ethernet
Ready
Link
P1
P2
5210-P
5210
Industrial RS-232 Device Server
Port 1 Port 2
RS-232 RS-232
— 3 —