Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for OMT STAND.MOVE M1.0
Summary of Contents for OMT STAND.MOVE M1.0
- Page 1 STAND.MOVE M1.0 Operating element for the STAND.CONTROL C1 + C2...
-
Page 2: Table Of Contents
Installation ..........................12 Unpacking ........................12 Installation ........................12 Commissioning ........................14 Commissioning the controller, general ................14 Commissioning the STAND.MOVE M1.0 ............... 14 Operation ..........................15 Height-adjustment......................15 Set and delete shelf and container stop ................. 15 Disassembly/Maintenance ...................... 17 Maintenance ........................ -
Page 3: Preface
The operating element must be installed in accordance with these instructions. Any changes to the desk base or any improper usage can have an effect on the safety, functionality and service life. These operating instructions have been written for the STAND.MOVE M1.0. Oelschläger Metalltechnik GmbH STAND: 17.06.2019... -
Page 4: Explanation Of Terms And Index Of Abbreviations
2 Explanation of terms and index of abbreviations Abb./Term Meaning Oelschläger Metalltechnik GmbH Controler Table controller STAND.CONTROL C1 or C2 Reset position Lowermost mechanical end position of the table Minimal position Lowermost software end position of the table STAND: 17.06.2019 9910_Operation-Manual_STANDMOVE_M1-0_Rev1v0_EN Seite 4 von 23... -
Page 5: Safety
Knowledge of the following is a precondition for commissioning and installation of the operating element STAND.MOVE M1.0 in combination with the table controller STAND.CONTROL C1 or C2: Mechanical and electrical basic knowledge (a corresponding training) Reading the operating instructions Symbols used in the instructions Stands for an immediate, threatening danger. -
Page 6: Safety Instructions
These operating instructions contain safety instructions that inform you about potential hazards and thus facilitate safe operation of the STAND.MOVE M1.0, in combination with the table controller STAND.CONTORL C1 and C2. Please be sure you comply with these safety instructions! This section provides you with general safety information that does not refer to any specific work step. -
Page 7: Safety Instructions Für Resellers
Warning: Make sure that no unauthorised persons (small children, persons under the influence of medication, etc.) handle your product or the STAND.MOVE M1.0 Repairs Attention: In the interest of preventing mal-functions, only authorised service person- nel are permitted to make any repairs. - Page 8 Attention: If the handswitch is opened, there is a risk of subsequent malfunctions. In case of a technical defect on the STAND.MOVE M1.0, please contact an authorised customer service representative. Section 11 contains solutions for the most common errors. STAND: 17.06.2019...
-
Page 9: Warranty
STAND.MOVE M1.0 must not be incorrectly handled or used and no changes are permitted to be made to the handswitch; otherwise, the warranty expires. Please see our General Terms and Conditions of Business for more information. -
Page 10: Overview
5 Overview Figure 1: Depiction of the operating element STAND.MOVE M1.0 RJ45-socket Button Up Button Down STAND: 17.06.2019 9910_Operation-Manual_STANDMOVE_M1-0_Rev1v0_EN Seite 10 von 23... -
Page 11: Scope Of Supply
6 Scope of supply Note: The operating element STAND.MOVE M1.0 may only be used with the table controller STAND.CONTROL C1 or C2. Delivery scope The delivery scope contains: STAND.MOVE M1.0 Other accessories required for operation can be obtained from OMT. -
Page 12: Installation
Installation Install the table controller STAND.CONTROL C1 or C2 in accordance with the relevant manual. Install the operating element STAND.MOVE M1.0 on the front table edge on the underside of the table-top (see Figure 2). You will need the following material and tools for the installation:... - Page 13 1. Position the operating element at the desired place on the table-top. 2. Mark the location of the drill holes with a pencil. 3. If required, pre-drill the marked locations for the screws using a drill. 4. Fasten the STAND.MOVE M1.0 with the two screws. STAND: 17.06.2019 9910_Operation-Manual_STANDMOVE_M1-0_Rev1v0_EN...
-
Page 14: Commissioning
Note: Before commissioning, the controller and the handswitch must be electrically deenergised. Commissioning the controller, general STAND.MOVE M1.0 is employed as an operating element for the STAND.CONTROL C1 or C2 control- ler. Please follow the operating manual of the corresponding STAND.CONTROL for the commissioning. Commissioning the STAND.MOVE M1.0 If you are using a STAND.CONTROL C1, connect the hand switch to one of the RJ45 sockets (D1 or... -
Page 15: Operation
9 Operation Figure 3: Hand switch STAND.MOVE M1.0 Oelschläger Metalltechnik GmbH offers its customers various variants of the STAND.MOVE M1.0. All our hand switch models are available with and without the logo printed on them. The functions described can be used with all variants of the STAND.MOVE M1.0 model. - Page 16 Note: With the additional stops, the safety of the table system can be increased, in that the possible movement path is restricted. Container- and shelf stops are safety positions that cannot be run over during normal operation, so that collisions with known, permanently present hindrances can be prevented. The container stop limits the movement height downwards (minimum height) and can be used if there are limiting factors below the table, for example, a Rollcontainer.
-
Page 17: Disassembly/Maintenance
Therefore, only agents with a pH value of 6-8 may be used. The Handswitch STAND.MOVE M1.0 can be wiped from the outside with a soft cloth. Coarse soiling may only be removed with a soft, damp cloth. Ensure that no moisture penetrates into the housing. -
Page 18: Easy To Rectify Faults
11 Easy to rectify faults Warning: Before troubleshooting, especially on faulty cables, the controller must be isolated from the network. If a fault cannot be rectified as described, isolate the product from the voltage supply, wait for at least 3 minutes and try again. -
Page 19: Technical Data
12 Technical data The technical data of the STAND.MOVE M1.0 dimensions (L x B x H) 60 x 50.86 x 21 mm 2.36 x 1.97 x 0.83” cable length Standard length: 1.5 m Special lengths available on request weight 0.04 kg (with standard cable length) Environment conditions during transport and -25 °C to +70 °C at 5 % to 90 % relative atmos-... - Page 20 STAND: 17.06.2019 9910_Operation-Manual_STANDMOVE_M1-0_Rev1v0_EN Seite 20 von 23...
-
Page 21: Tests And Certificates
13 Tests and certificates The drive system is tested according to the following standards: Electromagnetic compatibility (EMV-Directive 2014/30/EU): EN 61000-6-2:2005 Electromagnetic Compatibility (EMC) EN 61000-6-3:2007+A1 Electromagnetic Compatibility (EMC) EN 61000-3-2:2014 Electromagnetic Compatibility (EMC) EN 61000-3-3:2013 Electromagnetic Compatibility (EMC) Electrical safety (low voltage directive 2014/35/EU): EN 62233:2008 Safety of persons in electromagnetic fields EN 60335-1:2012+A13... -
Page 22: Disposal
14 Disposal The FREE.STAND table-top support frame in which the STAND.MOVE 1.1 is fitted is an electrical and electronics device that must be disposed of separately from household waste, in accordance with the applicable WEEE-directive 2012/19/EU. Figure 4: Identification markings for products in accordance with WEEE Directive 2012/19/EU Dispose of the product and all other materials and parts in an environment-friendly manner, in accord- ance with the applicable national regulations in your country. -
Page 23: Additional Information
9 for generating the end user documentation for the height-adjustable table, in which the STAND.MOVE M1.0 was integrated, for 10 years from delivery, free of charge. This licence does not include any logo, design or page layout elements of Oelschläger Metalltechnik GmbH. The cus- tomer may make all the necessary changes to the text and graphics to match them to the purpose of the end-user documentation.