Subscribe to Our Youtube Channel
Related Manuals for ersa i-CON 1V
Summary of Contents for ersa i-CON 1V
- Page 1 Ersa i-CON 1V & i-CON 1VC Soldering station Quick guide Ersa GmbH Leonhard-Karl-Str. 24 Phone +49 9342/800-0 97877 Wertheim/Germany Fax +49 9342/800-127 www.ersa.com service.tools@kurtzersa.de...
-
Page 2: Table Of Contents
7. i-Tool ........................11 7.1 How to change a hot soldering tip ..................11 7.2 How to change a cold soldering tip ..................11 8. Warranty ....................... 12 3BA00253-01 2021-05-17 Rev. 1 Ersa i-CON 1V & i-CON 1VC • •... -
Page 3: Introduction
This quick guide is intended to provide you with quick reference options when working with i-CON 1V / 1VC. The i-CON 1VC soldering station model is optionally available with a serial PC interface. Control signals for activating the Easy Arm 1 and Easy Arm 2 solder fume extractors or the IRHP 100A heating plate are also available at this interface. -
Page 4: Start-Up
■ If the soldering station is equipped with an additional interface on the back of the device, connect it there: Ersa solder fume extractor and preheating plate IRHP 100. ■ Place the soldering station and the relevant holder on a heat- resistant, conductive ESD work surface with a connected earthing plug, as described under ESD-hazardous components. -
Page 5: Functional Description
(press) function, thereby becoming effective for the station. All setting steps and measured values are shown in plain text in a clear display window, the “dis- play”. 3BA00253-01 2021-05-17 Rev. 1 Ersa i-CON 1V & i-CON 1VC • •... -
Page 6: Language Selection
Setting the temperature ■ To set the desired soldering tip temperature, turn the i-OP. ■ Press the i-OP to apply the setting. 3BA00253-01 2021-05-17 Rev. 1 Ersa i-CON 1V & i-CON 1VC • •... -
Page 7: Soldering
■ Perform some soldering trials. If you are not satisfied with the result, you can adapt the parameters to your requirements. As to this, read the following sections 3BA00253-01 2021-05-17 Rev. 1 Ersa i-CON 1V & i-CON 1VC • •... -
Page 8: Operation Modes
Working mode After switching on the station, the switch-on dialog ap- pears for approx. 2 seconds. This shows the station name ① and software version ② of the i-CON 1V. The station will then automatically switch to working mode. Parameter mode The parameter mode for the soldering tool is activated by pressing and holding the i-OP for approx. -
Page 9: Contrast
Activate the cursor by pressing the i-OP; pressing it again will switch the cursor back off. When the cursor is activated, the value of the parameter can be changed accordingly by turning the i-OP. 3BA00253-01 2021-05-17 Rev. 1 Ersa i-CON 1V & i-CON 1VC • •... -
Page 10: Troubleshooting
• Is the soldering tool properly connected to the supply unit? Error messages The i-CON 1V carries out fault diagnoses independently. The result of a diagnosis is output as an error code: In this case, the triangular pictogram appears in the display ①... -
Page 11: I-Tool
How to change a hot soldering tip ① ② ③ 72°F 40°C ④ ⑤ ⑥ How to change a cold soldering tip 72°F 40°C ① ② ③ ④ ⑤ ⑥ 3BA00253-01 2021-05-17 Rev. 1 Ersa i-CON 1V & i-CON 1VC • •... -
Page 12: Warranty
Ersa drew up this instruction manual with utter care. However, no guarantee can be granted for its contents, completeness and the quality of the information provided there- in. - Page 13 3BA00253-01 2021-05-17 Rev. 1 Ersa i-CON 1V & i-CON 1VC • •...
- Page 14 Electronics Production Equipment Production plants/ subsidiaries Local agents Other presence America China Ersa GmbH Ersa North America Ersa Shanghai Leonhard-Karl-Str. 24 Pilgrim Road Plymouth, Room 720, 97877 Wertheim/Germany WI 53073 USA Tian Xiang Building. Tel. +49 9342/800-0 Tel. 800-363-3772 No. 1068 Mao Tai Rd.
Need help?
Do you have a question about the i-CON 1V and is the answer not in the manual?
Questions and answers