Advertisement
Declaration of Conformity
CE Conformity Statement
Radio products with the CE alert marking comply with the
R&TTE Directive (1999/5/EC) issued by the Commission of the
European Community. Compliance with this directive implies
conformity to the following European Norms (in brackets are
the equivalent international standards).
• EN 60950-1 (IEC60950-1) - Product Safety
• EN 300 328 Technical requirement for radio equipment
• ET S301 489 General EMC requirements for radio
equipment
Products that contain the radio transmitter are labeled with
CE alert marking and may also carry the CE logo.
FCC Compliance Statement
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
To assure continued compliance, any changes or modifications
not expressly approved by the party responsible for
compliance could void the user's authority to operate this
equipment. (Example: use only shielded interface cables when
connecting to computer or peripheral devices).
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions:
1)
This device may not cause harmful interference, and
2)
This device must accept any interference received,
including interference that may cause undesired
operation.
15.21
Any changes or modifications not expressly approved by the
party responsible for compliance could void the authority to
operate equipment.
This device and its antenna must not be co-located or
operating in conjunction with any other antenna or
transmitter.
End-users and installers must be provided with antenna
installation instructions and transmitter operating conditions
for satisfying RF exposure compliance.
For product available in the USA/Canada market, only
channel 1~11 can be operated. Selection of other channels is
not possible.
FCC Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure
limits set forth for an uncontrolled environment for body-
worn configuration in direct contact to the phantom.
This device complies with FCC radiation exposure limits set
forth for an uncontrolled environment.
This equipment complies with FCC radiation exposure limits
set forth for an uncontrolled environment. End user must
follow the specific operating instructions for satisfying RF
exposure compliance. This transmitter must not be co-
located or operating in conjunction with any other antenna or
transmitter.
The portable device is designed to meet the requirements for
exposure to radio waves established by the Federal
Communications
Commission (USA). These requirements set a SAR limit of 1.6
W/kg
averaged over one gram of tissue. The highest SAR value
reported under
this standard during product certification for use when
properly worn on the body
The grantee is responsible for ensuring that the EUT meets
Section 15.407(g) requirements.
IC warning statement
This device complies with Industry Canada's licence-exempt
RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and (2) This
device must accept any interference, including interference
that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada
applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes : (1)
l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur
de l'appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d'en compromettre
le fonctionnement.
This radio transmitter has been approved by Industry Canada
to operate with the
antenna types listed below with the maximum permissible
gain and required
antenna impedance are strictly prohibited for use with this
device.
Le present emetteur radio a ete approuve par Industrie
Canada pour fonctionner
avec les types d'antenne enumeres ci-dessous et ayant un
gain admissible maximal
et l'impedance requise pour chaque type d'antenne. Les types
d'antenne non inclus
dans cette liste, ou dont le gain est superieur au gain maximal
indique, sont
strictement interdits pour l'exploitation de l'emetteur.
(i)the device for operation in the band 5150–5250 MHz is only
for indoor use to reduce the potential for harmful
interference to co-channel mobile satellite systems; (For
devices installed in vehicles point i. is not required.)
Users should also be advised that high-power radars are
allocated as primary users (i.e. priority users) of the bands
5250-5350 MHz and 5650-5850 MHz and that these radars
Advertisement
